Search Documents

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Kurt Westerlund

Three years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm3/0h at Boliden Rönnskär Sweden on a TBRC smelting galena (PbS). Operating experience from the Kivset flash WHB 11.900 nm3/h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3/h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Baicheng Liu, Houfa Shen, Wensheng Li

"In order to understand the formation of macrosegregation in steel ingots, a mixture model has been developed which accounts for coupled mass, momentum, species, and energy transport to describe the sedimentation of free equiaxed grains during solidification. In this model, the mushy zone is divided into the slurry and porous regimes according to a solid packing fraction. Settling velocity of equiaxed grains in the slurry regime is given by an explicit expression. The solidification of a binary steel ingot (Fe-0.36wt.%C) with a two-dimensional geometry is numerically simulated. It is demonstrated that the predicted macrosegregation patterns agree to some extent with classical experimental results. Further refinement of this model is still necessary for realistically simulating steel ingot solidification.IntroductionModeling macrosegregation in steel ingots is still a challenging study, mainly due to the length scale of the products and the complexity of global multiphase transport phenomena coupled with microscopic solidification kinetics [l]. The thermal-solutal convection and the motion of equiaxed grains are the two main mechanisms responsible for macrosegregation. But there are few models that deal with the motion of equiaxed grains, which is confirmed as the main phenomenon that explains the negative macrosegregation along the centerline of large steel ingots [2]. A model which takes into account melt convection and grain sedimentation was first proposed by Beckermann and co-workers ([3], and references therein). More recently, similar multiphase solidification models with advanced nature have been presented by Wu and Ludwig [1,4] and Combeau and co-workers [5,6]. It is known that the application of these sophisticated models to steel ingot casting is at its beginning.In this paper, a solidification model based on continuum mixture approach, using much less sophisticated relations to obtain the settling velocity of free equiaxed grains, has been proposed in order to predict the macrosegregation in steel ingots. The model is applied to simulate the solidification of a binary steel ingot with a two-dimensional geometry, and preliminary modeling results are presented."

Jan 1, 2011

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By Donato Firrao, Giorgio Scavino, Paolo Matteis

"The fatigue behavior of two high-strength sheet steels used to produce car bodies, a dual-phase steel and a TWIP one, both with ultimate tensile strength close to 1 GPa, is investigated.Unnotched tensile specimens are fatigue tested at room temperature with constant load amplitude and zero load ratio, in order to determine their 1 million cycles fatigue limit, both in the asfabricated sheet condition and after the resistance spot welding of one small homologous sheet square onto the calibrated length of the tensile specimen. Moreover, pre-cracked compact tension specimens are tested with load ratio 0.1 to determine the Paris fatigue crack growth curve.The fatigue results are completed with crystallographic, microstructural, tensile, and fractographic examinations, and the influence of the microstructure and of the welding processes is discussed.IntroductionCar bodies are increasingly made with high-strength weldable steels, in order to reduce vehicles' weight (to save fuel and reduce air pollution) and to improve the vehicle occupant safety in case of car crash. The main mechanical requirements of these steels in service are fracture strength and energy absorption, relevant for crashes, as well as fatigue endurance, relevant for ordinary car usage. [1]Steel sheets for car-body applications are usually made by continuous casting, hot rolling, cold rolling, continuous annealing (or other continuous heat treatment), and protective coating (in some cases). The sheets are then cold formed (deep drawn) to produce car body parts. Finally, the car bodies are built by assembling several deep-drawn parts, often consisting of different steels, usually through the Resistance Spot Welding (RSW) process, whereby two or three overlapping sheets are welded by local Joule-effect heating [2].Dual-Phase (DP) steels are widely used, low alloy steels with a microstructure consisting of ferrite and martensite, obtained from a final heat treatment which consists of heating at an intercritical temperature and then quenching. [3,4]"

Jan 1, 2012

By Jean Igor Margem., Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Sergio Neves Monteiro, Artur Camposo Pereira, Rômulo Leite Loiola

"The fibers extracted from the stem of the bamboo plant have been investigated as possible reinforcement composites due to their relatively high tensile strength. Although previous works have already been conducted about the mechanical properties, up to now a dimensional characterization of the distribution and the effect of diameter on the elastic modulus of bamboo fiber of the specimen dendrocalmus giganteus has not been performed. The aim of the present work was to statistically characterize the distribution of the diameter of a lot of bamboo fibers of that specimen. Based on this characterization, diameter intervals were set and the dependence of the Elastic Modulus (E) of theses fibers with a corresponding diameter was analyzed by the Weibull Method. The results indicated an inverse dependence, in which the highest Elastic Modulus were obtained for the thinnest fibers. Moreover, it was found that a mathematical hyperbolic relationship fit well this inverse correlation between the Elastic Modulus and the bamboo fibers diameters.IntroductionBamboo is a well known grass-type plant with a hard and stiff stem or culm that can reach, in some species, more than 10 cm in cross section diameter and stand several meters height. Owing to its low density, approximately 0.9 g/cm3, bamboo culms have been used in house construction from scaffoldings to panels. As an abundant natural resource in tropical and temperate regions, specially in Asia and South America, bamboo is also a substitute for wood and plastics in furniture and lightweight parts of automobile [1,2]. The cylindrical shape of the culm is, however, a limitation for its direct use in engineering systems. Consequently, research works have been conducted on bamboo fibers stripped off from the culm as reinforcement of polymer composites. [1-12]. According to Shin et al [3] bamboo fiber-epoxy laminates can be made into specific sizes and shapes, preserving the natural microstructural properties. These fiber composites overcome the limitation of the culm's cylindrical macrostructure. As a further advantage, Shin et al [3] indicated that cracking and bioerosion caused by insect pests is prevented."

Jan 1, 2013

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By Jinrong Zhang

Fresh cyanide solution was treated by near UV light with the assistance of photocatalysts. Cyanide was oxidized mainly to cyanate. Photochemical behavior of the anatase and rutile forms of TiO2 was compared. It is found that anatase has a much higher activity than that of rutile. Bubbling of oxygen in the reactor showed no appreciable increase in cyanide oxidation, implying that the reaction is surface controlling. A very interesting finding in this study is that a natural mineral, ilmenite, can replace chemical titanium dioxide as the photocatalyst. Ilmenite without any treatment did not catalyze the oxidation of cyanide. But, after being roasted at high temperature with oxygen, the oxidation was enhanced dramatically. The mechanisms of photooxidation of cyanide and the roasting of ilmenite are proposed.

Jan 1, 1991

By José Roberto de Oliveira

In a smelting reduction process the reduction reaction occurs predominantly in the liquid state. The main reduction agent is the carbon from the carbon saturated iron bath. The aim of the present work was to determine the velocity equation and the rate constant of the reduction rate of MnO content in a Mn0-SiO2-Fe0 slag by iron saturated carbon and the carbon dissolution rate in a Fe-Mn bath. The manganese content in the iron bath was in the range of 5 to 15 wt.%. It was observed that the rates of carbon dissolution in all Fe-Mn baths are faster than the rates of MnO reduction by the carbon saturated liquid iron.

Jan 1, 1999

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Mark Khinkis, Huajun Yuan, Mark Zak, Yaroslav Chudnovsky, Aleksandr Kozlov

"An afterburner for green petroleum coke calcination in electrothermal fluidized bed was designed, fabricated, installed, and tested on a pilot fluidized bed calcination furnace. The experimental set-up comprised a combustion chamber, in which fine particles and volatiles of the furnace off-gas were fully combusted, and a cooler equipped to calculate the related heat recovery and losses. Off-gas composition was analyzed to evaluate the combustion process. The energy balance confirmed the potential to recover a large part of the heat value of volatiles and fme particles from the GPC. Potential future applications of the results are discussed.IntroductionGreen petroleum coke (GPC) is an oil refining byproduct that can be used directly as solid fuel or as feedstock for the production of calcined petroleum coke [1-2]. GPC contains a high amount of volatiles and sulfur. With coke calcination, the GPC is heated to remove the volatiles and sulfur in the calciner off-gas to produce purified calcined coke, which is used in the production of graphite, electrodes, metal carburizers, and other carbon products. Currently, more than 80% of calcined coke is produced in rotary kilns or rotary hearth furnaces. These technologies provide partial heat utilization of the calcined coke to increase efficiency of the calcination process, but they also share some operating disadvantages [3]. On the other hand, coke calcination in an electrothermal fluidized bed opens up a number of potential benefits for the production enhancement while reducing the capital and operating costs.The increased usage of heavy crude oil in recent years has resulted higher sulfur content in green coke produced from oil refinery process, which requires a significant increase in the calcinations temperature and residence time [ 4]. The calorific value of the process off-gas is quite substantial and can be effectively utilized for combined heat and power (CHP) production to complement the energy demand. Waste heat recovered from the product cooling could also contribute to the overall economics of the calcination process. Preliminary estimates indicated the decrease in energy consumption by 35-50% as well as a proportional decrease in greenhouse gas emissions. So, efficiency improvement of the coke calcinations systems is attracting close attention of the researchers and engineers throughout the world."

Jan 1, 2014

By R. Boussaa, Y. Fautrelle, K. Zaidat, O. Budenkova, B. Saadi, X-D. Wang, L. Hachani, H. Ben Hadid

"Comparison of experimental data obtained in a benchmark experiment of solidification of a Sn-3%wt.Pb ingot and numerical results of two-dimensional and three-dimensional simulations of the process is presented. The benchmark experiment consisted in solidifying a rectangular ingot of Sn-3%wt.Pb alloy using two heat exchangers. Conditions of solidification were thoroughly controlled due to six thermocouples embedded into each heat exchanger. Due to another array of thermocouples the evolution of the temperature field at a lateral wall of the crucible was registered during the whole experiment. A treatment of the temperature data provided an estimation of the velocity field in the experiment. Post-mortem analyses of the sample provided the pattern of macrostructure of the sample and qualitative segregations pattern. 2D and 3D numerical solidification models are developed to give the distribution of the solute in a solidified sample.IntroductionConvection, either natural or forced, plays a very important role during the solidification. Its intensity and flow pattern affect heat and mass transfer and, consequently, macrostructure and segregation in a solidified ingot [1-4]. The effect of buoyancy convection during solidification has been studied in many laboratory-scale experiments [5-6]. Due to these experiments a general comprehension of formation of various defects in the ingot has been achieved. However, mentioned studies were not consistent since alloys, solidification conditions and configurations were every time chosen arbitrary. That is why the role of each parameter characterizing solidification process remains unclear. Moreover, the question of reproducibility of defects under the same solidification conditions still exists. In addition, most of the experiments suffer from the insufficient knowledge of control parameters that makes difficult their use for validation of models for solidification. These parameters serve as boundary conditions for numerical modeling and their incomplete description leads unavoidably to the errors in simulations. This situation motivated us to develop a setup for benchmark solidification experiments and to perform a set of the solidification experiments which we reported in [7]. Here we presented a comparison between results obtained in a benchmark experiment of solidification of Sn-3%wtPb ingot and its numerical modeling, which was performed in two-dimensional and three-dimensional configurations."

Jan 1, 2012

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Y. Iguchi, T. Narushima, T. Shiozawa, M. Maruyama, R. Arashi

"In situ observation system for thermal oxidation using Raman spectroscopy' was constructed, and oxide films formed on liquid pure Al and Al-Mg alloys (Mg contents = 1 and 4 mass%) were analyzed at room temperature to 1273 K in dry oxygen. In situ Raman spectra of the surface of a liquid Al-:-4mass%Mg indicated the formation of MgO • AlP3 (spinel) as oxidation products, while a -AlP3 and MgO • Alz03 (spinel) were observed on a liquid Al-1mass%Mg alloy. It was suggested that the formation of MgO film affected oxidation behavior of these alloys.IntroductionLiquid aluminum alloys are cast to ingots mainly by the continuous casting process. It is well-.known that surface cracks could be caused by oxide films formed on the surface of melt during continuous casting and defects due to the film. With regard to oxidation behavior of liquid aluminum alloys, many investigations l -s have been carried out from the view point of formation of ceramic metal composites(CMC) which are expected as cutting tools and structural materials 1.2. It is very important for reasonable continuous casting and CMC formation processes to elucidate oxidation behavior of melts.Oxidation behavior of materials generally depends on compositions and properties of oxide films formed on the surface. If in situ observations of oxide films are available during oxidation, evaluation of oxide films and interpretation of oxidation mechanism could be expected. Laser Raman spectroscopy is one of the most appropriate techniques for in situ observation of oxide films under various atmosphere at high temperatures. The authors have discussed the effects of atmospheres and sample compositions on oxide film formation mechanism on Fe-Si alloy6 and SiC-B4C composite7 on basis of an in situ observation by Raman spectroscopy. In spite of many previous studies, systematic and clear explanations have never been gotten on oxidation behavior of liquid aluminum alloys. And no in situ observation has been made except for transmission electron microscopy(TEM) and X-ray diffraction(XRD)."

Jan 1, 1996

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012

By Michael S. Moats, Alexander Derrick

"The Winand Diagram was developed and has been used for decades to illustrate the interaction between polarization, mass transport and inhibition on the resulting structure of a metal electrodeposit. Recently, Adcock et al. criticized the Winand Diagram and developed their own structural diagram based on nucleation and plating overpotentials. Their work was based on zinc electrodeposition using a galvanostatic staircase method. This work explores the nucleation and plating overpotentials for copper electrodeposition using conditions typical for primary electrowinning and the galvanostatic staircase experimental technique. Additionally, the effects of organic additives and plating substrate on these overpotentials are reported.IntroductionThe control of electrodeposited structures is critically important to modem electrometallurgy operations to insure proper quality and efficient energy use. Electrodeposition of base metals for primary recovery (e.g. electrowinning or electrorefining), while similar to plating for decorative or device manufacturing, differs in the need to produce deposits that cover large areas and grow to significant thickness. Thus, controlling nucleation and particularly growth of electrodeposits is critically important for base metal electrometallurgical operations.The control of nucleation and growth on an industrial scale is most influenced by five parameters - current density, temperature, metal concentration, electrolyte agitation and additives. The effects of these parameters on electrodeposition are interrelated. To describe their effects on the type ofelectrodeposits generated and provide practitioners with a useful tool, Winand developed what is known as the Winand Diagram [1-2]. An adapted version of the Winand Diagram is shown in Figure 1.Winand characterized electrodeposits using Fischer's classification [3] and plotted the various deposit types versus inhibition on a vertical axis and the ratio of current density to bulk metal concentration on the horizontal axis. Inhibition intensity is a complex parameter and is still not well understood even though Fischer introduced the term in 1960 [4]. Often, inhibition intensity is simplified to equal the concentration of organic additive at the deposit surface and is related to the inverse of the exchange current density of the metal being deposited. The ratio of current density to bulk metal concentration is used to represent the ratio of crystallization overvoltage to mass transport of the depositing ion. As such i/iL could also be along the horizontal axis, where iL is the limiting current density of the electrodeposition reaction."

Jan 1, 2012

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By Chang Wei, Zhigan Deng, Yizhao WANG, Cunxiong Li, Gang Fan, Xingbin Li

During the process of hematite precipitation, the transformation of Na jarosite convert into hematite has been studied in a batch reactor at different temperatures, ranging from 170°C to 200°C with 3h of the retention time in the presence of 30g/L Fe ( ) and 4g/L Na+. The composition of precipitation was seriously depended on the temperature, at 170°C hematite and sodium jarosite are the reaction products of iron precipitate, with an increasing in reaction temperature the sodium, sulfur content in precipitated decreased and sulfur mainly exist in forms of SO4 2-, and when temperature over 200°C hematite was the only phase in product. An increasing temperature was not only beneficial to iron precipitation, also conducive to jarosite conversion to form high quality hematite precipitate.

Jan 1, 2016

By K. Asokan, K. Subramanian

"Electrowinning of copper by monopolar cells require common anode and cathode busbar and crossbars to connect each electrode to the respective common busbar. On the other hand, the bipolar configuration warrants the end electrodes only to be connected to busbars; there is substantial reduction in copper requirement. In the present work, an electrowinning cell with bipolar electrodes and end electrodes, each having an area of 1000 cm2 was designed and operated. The bipolar electrode is made of mixed metal oxide coated titanium mesh welded to plain titanium sheet. Coated titanium mesh acts as anode and the plain titanium sheet acts as cathode. Environmentally unacceptable lead anode and the recurring loss of lead are done away with. Closer spacing of the electrodes, paves way for the application of higher current density leading to mass transfer enhancement. Performance of bipolar copper electrowinning cell is reported.1. IntroductionThe normally adopted practice in electrowinning of copper is the conventional monopolar configuration. In this practice, the individual electrodes act either as anode or cathode. Hence there is a need to connect every one of the electrodes to the common anode or cathode busbar and crossbars running across the top of the cell are necessary. The common busbar carries very high current which is divided among the individual crossbars and hence has to be thicker in relation to the current load of the cell. The drawback of the need to use common busbars of thicker cross section and the need to have crossbars are obviated in the bipolar configuration."

Jan 1, 2009

By Hiroshi Maeta, Takao Kino, Hirota Osono, Kikuo Matsusaka, Azusa Shida

"Prior to refine an ultra-high purity material, it is necessary to estimate the surface cleanness of a base material. In this report, the cleaning method of a surface for refining of an ultra-high purity aluminum has been studied. Aluminum sample of 99.999% purity was p9lished mechanically and electrically and washed with various solvents. Surface composition and a depth profile near the surface were examined. Based on the experimental results, surface structure of an ultra-high purity aluminum was discussed.IntroductionRecently, studies on high purity metals have become of interest, and we have reported .various properties of an ultra- high purity aluminum1- 2)In order to purify a metal, it is necessary to clean a work area and to make vacuous as possible. So, we are studying the purification of aluminum by an ultra-high vacuum refining system and a zone refining system set up in a clean room with cleanliness class of 1000.Now, in order to avoid a mixing of impurities into the refining metal, a surface cleanness of a base metal is very important factor. The purity of the base aluminum used our work is 99.999%, but the surface state of the base aluminum is not clear. Aims in this work .are to investigate the surface state and to obtain the cleaning method of the base aluminum.Experimental procedureSamples used in this work were 99.9% (3N), 99.99%(4N) and 99.999% (SN) aluminum produced industrially and 99.9999% (6N) aluminum purified by us."

Jan 1, 2000