Search Documents

By Yuhua Pan

Generic mathematical models have been developed for simulating heat transfer in two types of slag resistance heating electric furnaces for sulphide smelting: i) six-electrode-in-line rectangular furnaces and ii) three-electrode circular furnaces. The models are based on three-dimensional steady-state heat transfer of conduction, convection and radiation. Solidification of liquid slag into solid slag by water-cooling units, for use as freeze lining of furnace walls, is also considered in the models. The developed models are capable of providing predictions with reasonable accuracy for electric furnaces on 1) temperatures in slag, matte, cooling water, freeze lining and other solid regions as well as temperatures at various fluid/solid interfaces, 2) freeze lining thickness, 3) furnace smelting rate and 4) furnace heat loss rate. These computer models are built into executable application programs that are very efficient, with execution time less than one second, and can be easily portable to most computing platforms. This paper describes, as an example, the modelling results on heat transfer in six-electrode furnaces. The major modelling results show that in six-electrode furnaces uniform electric power inputs to the electrodes likely lead to low temperature regions close to slag and matte tapping ends of the furnaces, and the power input and the formation of air gaps between freeze lining and cooling units have significant influences on the thickness of freeze lining maintained by the cooling units.

Jan 1, 2006

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

By Mamoru Kuwahara, Tomohito Taki, Masamichi Sano

"Theoretical basis and experimental results on ultrasonic separation of dispersed inclusions from molten metal are outlined. Transitional formation of an ultrasonic standing ·wave field in a liquid bath is numerically predicted based .on the wave equations. Numerical solution of the equation of motion of a fine particle in a standing wave field indicates that the inertia term can be neglected during conventional ultrasonic separation of fine particles: Analytical solutions for the position at which particles are coagulated the minimum power for separation, and the ultrasonic separation time are derived to incorporate such key process parameters as the density difference and the acoustic energy density exerted. Cold model experiments have been carried out to observe ·transitional coagulation of polystyrene particles in an aqueous sugar solution with the incidence of standing ultrasonic plane wave. Experimental results agree well with the theoretical predictions.IntroductionDespite of recent progress of fundamental and applied researches in metallurgical systems, advanced materials· with less inclusions and better properties may demand more innovative processing in a: molten state. It may be realized by applying electromagnetic and/or ultrasonic external fields to the systems. The present authors1)·2) have been proposing : new methods of ultrasonic processing of materials based on such phenomena as acoustic streaming, acoustic radiation pressure on dispersed phase in a standing wave field, and the cavitation in liquid associated with use of high-intensity ultrasound and so on. Taking account of common physical natures between ultrasound and sound wave, we call such · a processing assisted by acoustic wave as ""sonoprocessing"". This report ·deals with some theoretical and technological aspects on the ultrasonic separation of fine particles from liquid, which could become an important operation to produce clean materials. Fundamental theory and ·supporting experimental results will be given below to give an insight into the liquid metal sonoprocessing."

Jan 1, 2000

By Fatbardha Osmani, Skender Osmani

"A system analysis of the resource and environment management (water, energy etc) starts from its definition. Unfortunately, there is not a unique semantics of the mentioned concept. On these circumstances, in this paper the following issues are presented: 1.A short view on the existing concepts of management. 2.A new definition on the concept of management. It is considered as a complex and rational activity on human and natural resources ,environment etc, which starts from a analysis of infrastructure ,technology , etc, mission , alternatives , project etc. and ends to an optimal output. Basing on this definition, the management has two principal components: strategy and policy. The strategy is referred as a blue print program (the same definition as in Game Theory), which contains all the contingency alternatives. , while the policy is referred as a strategy applied into practice. The strategy is the first , while the policy is the second one. The best alternative of a policy is the project, Each strategy has one and only one project. The mentioned definition erases the differences between concept of policy and politics. Each strategy has its alternatives ,the next has its sub strategy and so on, i.e. whatever are going to be the strategy, there are a hierarchy composed by sub strategies up to the simplest strategies applied by a single individual (human beings or robots). The strategy objectives are necessary and sufficient conditions for its realization i.e . the strategy is an optimal activity, in which all resources are integrated and processed . Several strategies could be joined into one( for example the surface water strategies of the Balkan countries) . In this view, the strategy could be globalized into optimal way basing on different criteria’s as social, economic, environmental, their risks and effectiveness etc. etc An example from the water management illustrates the mentioned concepts."

Jan 1, 2008

By D. Nozadze

A new method of isothermal electro-contact diffusion welding of layered composites under pressure is offered. The scheme is developed and laboratory installation is created on which preproduction models of the layered composite of steel and aluminum is produced. A new method of electro-contact hot deformation is proposed for realization of diffusion welding by pressure of stratified blanks providing high-temperature isothermal process. In this case a rolling process or composite pressing is meshed with simultaneous electric current transmission in deformation center. Considering that a resistance of transient layer far exceeds the resistances of composite components, the heat release takes place intensively just in this layer. As the surfaces are approached over a distance of inter-atomic forces, the energy of boundary atoms easily reaches the energy threshold of capture with a formation of qualitatively new metallic bond. Proposed method, providing isothermal process in deformation center, excludes a necessity of previous preparation and prevention of surfaces. In this case strength of layer connection may approximate or exceed strength limit of cladding layer.

Jan 1, 2006

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983

By Terence Makanyire, Animesh Jha

The dissolution and chemical properties of vanadium, zirconium, and niobium in rutile lattice are analyzed by comparing the octahedral site preference energies, with respect to Ti4+ ion in the solvent phase. The oxides are often present in rutile lattice and interfere in achieving the quality of pigment grade TiO2 due to favourable Gibbs energy for dissolution in the solvent rutile matrix. Binary mixtures of V2O5 { TiO2; Nb2O5 { TiO2 and ZrO2 { TiO2 with compositions of 80, 85, 90, 95 and 97 wt% TiO2 were made, pelletized and sintered at 1100 °C for 24 hours. The solidsolution mixtures were then cooled and leached in 2M NaOH for 3 hours at 60 °C. Phase and lattice parameter characterizations, and microstructural and compositional analyses were then carried out using X-ray diraction and SEM/EDX, respectively. The leachates were analysed by Atomic Absorption Spectroscopy (AAS), using which the solute dissolution model for oxides were investigated.

Jan 1, 2014

By Min Chen, Nan Wang, Zhen Tian, Yingying Shen

"The enrichment behavior of phosphorus in CaO-SiO2-FeOx-P2O5 slag was studied by making an investigation on the distribution of phosphorous content in slag and 2CaO·SiO2 phase. The research results showed that the existing 2CaO·SiO2 solid particles in slag were the sites for the phosphorous enrichment. The enrichment process of phosphorus in CaO-SiO2-FeOx-P2O5 slag can be recognized as: mass transfer of phosphorus from bulk slag toward the surface of 2CaO·SiO2 particle, superficial dissolution reaction of phosphorus to 2CaO·SiO2 and diffusion of phosphorus through the product layer of 2CaO·SiO2-3CaO·P2O5 solid solution to the inner of 2CaO·SiO2 particle. Compared to the 2CaO·SiO2 particles with larger size (500µm to 1000µm), the completion time of enrichment was shorter for the particles with smaller size (less than 50µm).IntroductionDuring ironmaking and steelmaking, significant amounts of slag are produced. Contrast to the high utilization of ironmaking slag, the treatment of steelmaking slag is more difficult and challengeable, and therefore, an alternative approach is to recycle the steelmaking slag inside the ironmaking and steelmaking process itself. The main limitation to the reuse of steelmaking slag inside the process is that the refining process may be aggravated caused by the phosphorous accumulation if it is used in the blast furnace burden [1]. At the same time, the phosphorous content of steelmaking slag (approximately 1%~5% P2O5) is too low for it to be used as raw material for fertilizer [2, 3]. Moreover, owing to the diminishing supply of global iron ores with low phosphorous content, the control of phosphorus in iron and steelmaking processes has become an increasing problem, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. Therefore, a valuable approach is quite appreciated in which the steelmaking slag is recycled within the ironmaking and steelmaking process and at the same time, the high phosphorus-containing phases in the steelmaking slag, suitable for use as fertilizer can be separated and recycled effectively [4]."

Jan 1, 2011

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By Marie-Aline Van Ende, In-ho Jung

A thermodynamic database for the oxyfluoride system CaO-MgO-Al2O3-SiO2-Na2O-K2O-Li2OMnO- FeO-F has been developed based on the critical evaluation and optimization of all available experimental thermodynamic and phase diagram data. The developed database can be used for phase diagram and equilibrium solidification calculations for multicomponent systems and for understanding the solidification behavior of mold fluxes. Based on this thermodynamic database, a simple kinetic model was developed to simulate the interactions between the mold flux and molten steel using effective equilibrium reaction volumes combined with the thermodynamic database.

Jan 1, 2014

By Haydar Güneş

In this study, a hydrometallurgical process was evaluated for the recovery of Nd from a Nd-Fe-B magnet. Each leaching test was performed at the solid (weight) to liquid (volume) ratio of 1:50 and was mixed at 400 rpm at ambient temperature. The effects of 3 different acids (HCl, HNO3, and H2SO4) on the extraction of Nd were investigated and H2SO4 was found to be more effective than other acid solutions. Under the optimal conditions, pregnant leach solution was produced with H2SO4 for subsequent Nd precipitation testing. Each precipitation test was carried out using 100 mL of feed solution mixed at 600 rpm at 25°C. NaOH and H2C2O4 were used for Nd precipitation. The highest Nd was precipitated as Nd2(C2O4)3, 10H2O with C2H2O4 at 20 min.

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Natural fibers are gaining attention as a class of low cost, biodegradable and renewable materials that also exhibit some interesting properties for specific applications. In particular, the incorporation of some natural fibers in polymeric matrix composites is nowadays providing opportunity of manufacturing a variety of industrial items, for instance automobile interior components. Among these fibers, ramie (Boehmeria nivea) is one of the least investigated and only recently was studied as polymeric composite reinforcement. Therefore, the objective of this work was to evaluate the possibility of ramie waste reinforced polyester composites to replace conventional building materials, such as plywood, plastic boards and gypsum panels in terms of a cost-benefit analysis.IntroductionThere is a growing concern over the environmental questions that are presently affecting our society in a global sale such as climate changes and generalized pollution. Among the solutions for these questions, the replacement of energy intensive materials, especially those long term degradable such as the synthetic fibers, is already being considered [1]. As a consequence, the past decades have witnessed an increase in research devoted to new biodegradable materials obtained from natural resources mainly the biomass. Important examples are the renewable natural fibers as well as composites incorporated with them [2,3]. In addition to their friendly status with respect to the environment, well know natural fibers like jute, sisal, wood, coir, hemp and flax are relatively low cost and recyclable. In recent works [4,5], the use of these cultivated and abundant lignocellulosic fibers was investigated as the reinforcement phase in polymeric composites.Other less know lignocellulosic fibers have also been recently investigated [6,7]. These are fibers that likewise show a potential of incorporation into the polymeric matrix of composite materials. Most of these less know fibers are typical of tropical regions and, in principle, their application in industrialized composites would represent job opportunities for developing countries in Africa, South Asia and Latin America."

Jan 1, 2008

By Yasumasa Hattori

An extensive study including fluid dynamic calculations, cold model tests, pilot plant tests as well as measurements in a commercial flash furnace was carried out in order to develop a new Sumitomo flash smelting concentrate burner. The pressure measurements in the commercial burner indicated that the premixing of the concentrate and reaction air in a burner was insufficient. Pilot plant tests showed that enhancement of the premixing of the concentrate and reaction air is very effective for improving the burner performance. Using the additional pressure drop of the reaction air as an indicator of the premixing, a new type Sumitomo premixed concentrate burner was developed.

Jan 1, 2003

By J. Boitano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Cbdelco..Chile. A discussion on design conditions for a Mure Sulphuric Acid Plant using Teniente Converter.gases.is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited .gas handling capacity for operation under Mure process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente converters installed in 1987-1989 Improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By Ledjane Barreto, Tulio Flávio Accioly de Lima e Moura, Wilson Acchar, Antonio Carlos Silva da Costal

"Clays are common ingredients in pharmaceutical products both as exclplents and active substances. Clay minerals are naturally cationic exchangers and they may undergo ion exchange with basic drugs in solution. Smectites, and montmorillonite have been studied due their high cation exchange capacity as compared to other silicates. Recently a patented study reports the use of attapulgite as the encapsulating agents both for the protecting the active substance and modulating release into the body. Some clays such as kaolinite, smectites, talc, etc are also used as dermatological protectors. Sepiolite and smectites have the ability to form complexes with organic compounds with absorb ultra-violet radiation, enabling them to be used in sun screens with protection factors. The objective of this work is to characterize the attapulgite in order to study the potential use of this clay material in the human health.IntroductionSince the begimling of time, nature has served humanity as a source of various raw materials. Among these, clays such as kaolinite and ilitte are common ingredients in the tile production. Recently, special clay materials have been investigated in order to identifY new potential uses of these class of materials. Clay materials are natural raw material and have excellent properties such as low toxicity, good biocompatibility, making them a good material to be used in biological applications. Attapulgite (paligorskite) and sepiolite is so called special clays. These special clay materials are very sin1ilar and have a great potential to be used in some technological areas due their special catalytic, sorptive and colloidal-rheological properties [1-8]. Recently some works have reported the use of these special clays materials for many applications such as drug delivery, wound dressing, oil absorbent, pesticides, fertilizers [9-12]. Brazil has a significant reserve of attapulgite located in Piaui state, making the study of the potential of this mineral in special areas, very attractive. Attapulgite is classified a fibrous alluminous silicate material and shows the presence of micro pores and channels, fine particle size and high surface area making this material a good candidate alternative material to be used in many industrial applications [6,8,9,11,12]. The objective of this work is to characterize the physical and microstructure of attapulgite."

Jan 1, 2012

By G. Hanko, A. Lebleu, M. Sibony, J. Lecadet

The New Jersey distillation process is today the most important pyrometallurgical method for the production of zinc of very high purity. The flexibility of the pyrometallurgical zinc production process, especially its ability for recycling, makes it competitive, although it is energy intensive. A deeper knowledge of the New Jersey process is necessary to further increase its technical performance by ensuring its global safety. A project, integrated in the European research program EUREKA, has been started in order to define the process chemistry of distillation. Experimental measurements have been carried out with a column at the laboratory scale, and the results, linked with industrial measurements, support the development of a model based on material and thermal balances. The first conclusions indicate that the key parameters for process optimization are the column geometry and the distribution of the thermal losses.

Jan 1, 2000

By Shinya Hodoshima

A catalysis pair of tetralin dehydrogenation / naphthalene hydrogenation has been proposed in the present paper as a liquid organic hydride for operating stationary fuel cells. Catalytic naphthalene hydrogenation, having been commercialized since the 1940s, proceeds to generate decalin via tetralin as an intermediate. The storage capacities of tetralin (3.0 wt%, 28.2 kg-H2 / m3) are lower than decalin (7.3 wt%, 64.8 kg-H2 / m3) but both tetralin dehydrogenation and naphthalene hydrogenation are much faster than the decalin / naphthalene pair. Moreover, existing infrastructures such as gas stations, chemical tankers and tank lorries are available for storage, transportation and supply of hydrogen. With respect to the stationary fuel cells with large space for hydrogen storage, tetralin as a hydrogen carrier is superior to decalin in terms of fast hydrogen supply or power density. Rapid hydrogen supply from tetralin under mild conditions was only accomplished with the carbon-supported metal catalysts in the ?superheated liquid-film states? under reactive distillation conditions. In contrast to the ordinary suspended states, the catalyst layers superheated in the liquid-film state gave high catalytic performances at around 250OC. As a consequence, both serious coke formation over the catalyst surface and excessive consumption of exergy were prevented simultaneously.

Jan 1, 2006

By Tobias Pröll, Bernhard Kronberger, Joachim Rohovec, Werner Hölt, Hermann Hofbauer

"As this is only a first draft, more precise explanations as well as detailed schemes, figures and plots will be included in the final draft. The description og the 100 kW test rig will also be mor detailed as construction is ongoing and will be finished during the summer. Furthermore simulations are to be finished shortly; so details on combustibles and gas concentrations will also be included in the final draft.AbstractOxyFuel combustion is a key technology for the efficient separation of CO2 from fuel combus¬tion (especially coal). Since coal plays a minor role in the Austrian energy mix the application of OxyFuel towards other fuels (biomass, waste fuels) is interesting to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alter¬native fuels is also interesting from a strategic point of view in order to generate knowledge for operation of capture ready cofiring and waste/sludge-incineration plants. OxyFuel uses a synthetic mixture of 02 and recycled exhaust gas where the 02 content may vary. This supplementary degree of freedom allows improved operation especially for low calorific fuels. Heavy fuel oil addition for low calorific combustibles can be omitted when using OxyFuel combustion. Application of alternative fuels (wood, waste wood, municipal waste, sewage sludge) in a 100-kW CFB plant is investigated in combination with process simulation.IntroductionOxyFuel combustion is discussed as one of the key technologies for the efficient separation of CO2 from combustion of fossil fuels (especially coal). Since coal plays only a minor role as primary energy source in Austria, the broadening of the scope towards OxyFuel of other fuels like biomass or waste fuels is necessary to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alternative fuels besides the large coal-oriented projects is interesting also from the strategic point of view. The presented project aims at the generation of knowledge in order to design and operate capture ready cofiring and waste/sludge incineration plants."

Jan 1, 2008