Search Documents

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By L. J. Lorig

Much of the present knowledge about caving behavior of rock masses has been obtained from empirical observations. Additional notions about caving have been developed through inferences derived from two-dimensional finite element analyses. These analyses have indicated that a combination of one low-angle set of fractures and one nearly vertical set of fractures is the optimum fracturing configuration for ease of cavability of an orebody. This paper presents the results of two- and three-dimensional distinct element analyses which draw different conclusions than those reported from finite element studies. The distinct element method is selected far analysis of cavability because this method treats the rock mass as an assemblage of rock blocks which may interact individually, The results of the analyses are compared to a documented case history which involved a groundfall of 80,000 tons of ore in a 160-foot high pillar. The mechanics associated with these results are-explained in terms of simple static stability analysis of wedges. The propensity for orebody caving is primarily a function of the number of joint sets or potential "release" surfaces in the orebody. This mechanism is influenced by the bounding weak discontinuities, and intact strength of rock material.

Jan 1, 1989

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By Trevor Rangasamy

Technically based guidelines for managing rock related risks associated with strip mines in South African collieries are currently vague and are to a large extent based on experience and trial and error. To date, no mine specific or universal design charts exist within the South African industry. Quantification is done on a reactive basis i.e. following reported instabilities. The conditions under which, proactive tools to manage instabilities would be practically applicable are: The design of simple easy to use charts. Designing the charts for a target audience that is primarily production management. Well organized, logical set-up of the charts that will allow for easy future refinements. Allowing for variations in rock and soil properties within the charts that would account for colliery specific and region specific variability. The factors selected for in depth investigation that were deemed to have either individually or in combination, a primary influence on the stability of strip mines are (in no order of priority): Appropriate batter angles for ?soft? materials. Surcharge loading (spoils, dumps, topographical highs) on the highwall side. Influence of the thickness of stratification on stability. Influence of moisture content on stability. Influence of the changes to the coal seam dip angle on stability. Influence of persistent ?strip long axis? parallel faults/joints on stability. Spoil stability for variations in material type. This paper provides details of the work undertaken, using principally numerical modelling techniques, to produce design charts that will allow for proactive management of rock-related instabilities on strip mines.

Jan 1, 2008

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By Haile Manteqi

In longwall coal mines, estimation of roof strata condition, sequence of loading, and supporting requirements are of a high degree of importance, and they are directly related to production and safety. Also, a prediction of the initial caving distance is rather complicated to calculate, because there are many parameters that effect caving process?roof and floor strata conditions, thickness of immediate roof, depth of cover, excavation geometry, and magnitude, and direction of principal stresses. This paper presents the results of 3D numerical modeling of the initial caving mechanism using the finite difference code FLAC3D at the E1 longwall panel of the Parvade 1 underground mine located in the Tabas area in the central part of Iran. The initial caving distance obtained was 10.4 m. Also, the results of numerical modeling have been compared to the analytical methods, such as Peng?s method. The results show good agreement with each other.

Jan 1, 2012

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By J. K. Whyatt

The paper presents an approach to design a multi level room and pillar layout in a 40m thick seam overlain by a major aquifer. The design was required to maximise extraction with due consideration of the general stability of the workings, the potential water hazards, and spontaneous combustion risks due to air leakage between horizons. The approach utilised was a combination of empirical pillar sizing for water hazard control with numerical modelling to assess potential interactions between horizons. The numerical modelling allowed the size of interleaves, and the appropriate staggers to be optimised in terms of stress distribution. The stress distribution allows both the general stability of the openings and more importantly the permeability changes around the openings to be determined. The permeability of coal is sensitive to stress, and an empirical stress to permeability relationship, and theoretical permeability to flow leakage relationship has been applied to interpreting the relative spontaneous combustion risk associated with each of the proposed layouts. The final proposed design is a compromise between maximum exploitation of reserves and consideration of water hazards and of spontaneous combustion risk. Further more detailed design will be required as more comprehensive data on the geotechnical properties of the coal and overburden become available.

Jan 1, 1996

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By Morgan M. Sears

In recent years, one large mine collapse and numerous smaller bump events have resulted in a renewed interest in coal bump research. With numerical modeling, the Energy Release Rate (ERR) calculation quantifies the ?release? of the gravitational potential energy of the rock mass into the environment as mining progresses. This release of energy can occur passively in the form of heat and sound or dynamically in the form of pillar bumps or rock bursts. From the initial application of a calculated energy release rate in the deep hard-rock mines of South Africa, the ERR was found to have a significant correlation with the risk or potential of damaging coal bumps or rock bursts. In this research, an ERR calculation is incorporated into the modern LaModel program to facilitate the analysis for potential coal bumps. Initially the ERR calculations in LaModel are verified using a case study of cut sequences originally modeled using the MULSIM/NL program. Then, the ERR calculations are applied to a bump-prone mine in Southern Appalachia were a number of different pillar recovery cut sequences were used in order to minimize the risk of bumps.

Jan 1, 2009

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By P. M. Lin

A subsidence monitoring program over a longwall panel was established (1) to explore the impacts of dynamic subsidence on the ground surface and structures and (2) to correlate the movements between the structures and their corresponding points on the ground. The program consisted of a transverse line survey and a series of survey points around the structures on the ground surface and their corresponding survey points on the exterior walls of the structures. The vertical displacement of each point can be expressed as: where Si is subsidence at i point; Sif is the final subsidence at i point; F is face location in terms of distance from the i point and SD is seam depth. The development of subsidence can be divided into five stages. Damage to the structures starts at the beginning of the second stage, The maximum damage developed in the middle of the third stage. The relationship of the vertical displacement between ground surface and structures can be expressed as: G = aH + b where G is ground displacement, H is structures displacement, and a and b are constants. The relationship is linear. However, the strain is non-linear and more complicated because of the interaction of the ground surface and structure.

Jan 1, 1989