Search Documents

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By Denise Müller, Axel Preusse

"Due to multilateral underground use, mining subsidence is discussed more and more with regard to issues other than mining, such as post-mining topics, storage, or geothermal use. These discussions and the influence of the energy policy is why the situation in Germany is described as a transition from active to abandoned mining. Many PhD theses have been written within the last 20 years—every single one with a different topic but all with the same issue—the effects and challenges of mining subsidence.These challenges start with the research regarding geological and hydrogeological conditions, which is the basis for calculations like the angle of draw or predictions of subsidence due to water table drawdown. Furthermore, the research investigates issues like risk-management and financial planning. One of these issues is post-mining calculations; others include potential hazards of storage or the use of geothermal energy.This paper outlines an overview of German mining and the consequences due to subsidence. It deals with an overview of the circumstances related to hard coal mining, lignite mining, the use of geothermal energy, gas, and opportunities regarding underground storage. Basically, it describes the essential steps of processing mining subsidence, starting with monitoring to forecast and up to safety measures.With a glance back to the applied research of the prior two decades, we compare given forecasts with experiences already gained.Even though mining decreases, ground control does not.INTRODUCTIONAfter the Second World War, an economic recovery started in Germany, during which the mining industry provided an advantage. Areas like the Ruhr District or Saarland were characterized by hard coal mining. In addition, there was lignite mining in the Rhenish mining area and the middle German coal district. In the Lausitz area, there were gravel and sand companies for the construction industry and many other medium-sized mining companies. Especially in the Ruhr District and in Saarland, where large coal fields were built, mining played a major role. The number of mines increased, and the negative effects on the terrain got bigger. While minor open pits or quarries have influences on the landscape only, large open pits and underground mining lead to significant ground movements. This results in a larger importance of mining subsidence engineering. Calculations of subsidence and forecasts have been developed and refined within the last several years. Due to the fact that the mining areas were and still are densely populated, the forecasts are getting more and more precise."

Jan 1, 2018

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By C. J. H. Brest van Kempen

The techniques developed should provide a useful tool, not only during the initial formulation of a suitable bolting plan for a new section, but also for periodic check¬ing on the utilization factor of hardware installed in the roof. Indications are that with present practice, utilization seldom exceeds 507.. Retro-fittable bolter equipment now available (FCBS?) allows doubling of the utilization factor in many cases. We are also introducing a computer pro¬gram based on the material outlined in this paper. This program can save a great deal of time in examining the real effect of implementing alternate bolting plans or using different installation techniques. It allows fine-tuning of bolt lengths, spacing and installation tension to mini¬mize roof support cost, while maximizing safe life of the mine opening. We have developed a procedure which allows easy, site-specific quantification of the need for reinforcement of a mine roof. The concept is based on the forma¬tion of a direct link between theory and empirical data to custom-fit each mine section. In its simplest form, the proce¬dure requires only recording of roof bolt torques in a sample working place (16 to 25 bolts) several times during the first week or so after initial bolting. The way in which the torque pattern changes during this time can reveal whether or not the bolts carry enough tension to maintain stability in that specific roof. From the same data, the nature of the anchorage horizon is derived. Specifically, shale or limestone can be distinguished from sandstone. If the procedure is repeated a few times (within the same mine section) with different bolt installation tensions, we can numerically characterize the roof in terms of one single value: an "effective angle of internal friction". This number can then serve to calculate trade-offs in bolting plan design, such as bolt length, bolt spacing and optimum bolt tension. Additional refinement is possible if a sagmeter is installed in the sample work¬ing place being monitored and if bolt anchorage capacity is determined. The lat¬ter can be done automatically on each bolt as it is being installed, using a system we developed and patented. Alternately, a number of pull tests could be performed. Using the sagmeter, bolt torque and anchor¬age data, it is possible to project the safe life of the supported opening. The details of the procedures described apply specifically to tensioned roof bolting, but a brief discussion paints the way for a similar analysis of full-column resin bolting also.

Jan 1, 1986

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Erdal Akyol

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By Song Yong Jin

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts, collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger.

Jan 1, 1992

Effective strata control, utilising fully encapsulated roof bolts, is dependent on the installed quality of the reinforcement elements. One mechanism by which fully encapsulated roof bolts may become less than fully effective is by gloving (glove fingering) and un-mixing of the resin. Following some small roof failures containing gloved bolts, investigations have been undertaken in some New Zealand coal mines to determine the extent of, and mechanisms involved in, the gloving of fully encapsulated roof bolts for a range of roof types and installation methods. Gloving, in this context, refers to the resin cartridge partially or completely enveloping a length of the bolt, typically with unmixed resin filler and catalyst/hardener remaining within the cartridge. Results have shown that gloving and un-mixing is a systematic and widespread phenomena, occurring across a range of resin and/or bolt manufacturers, and across a variety of roof types. Gloving was found in bolts installed using: hand held pneumatic and continuous miner mounted hydraulic methods, under run of mine (ROM) conditions by mine workers, and under controlled "best practice" conditions. The roofs bolts investigated are all 1800mm (6ft) long, and have shown that, on average, 485mm (-19") of the bolt length is gloved and/or unmixed. This equates to a 27 percent reduction in effective bolt length. The effected length of bolt is sufficient to impact on the load transfer/reinforcement capabilities of the bolt system, and hence impacts on the design assumptions and subsequent stability assessments. Furthermore, there is a direct relationship between the mechanism for the gloving of bolts and an increased occurrence of resin loss and reduction in encapsulations length in soft (less than 10 MPa) and/or highly fractured rock. Investigations have concentrated on developing an understanding of the mechanisms involved. This has been undertaken using both field installations and recovered bolts, as well as test bench trials. The mechanisms involved have been confirmed as being: the development of a pressure front as the bolt encounters the resin and is spun up the hole, which, in turn, leads to over-pressurisation and radial expansion of the resin cartridge, resulting in an increase in diameter of the plastic resin cartridge, which allows the bolt to be spun up into the cartridge without making sufficient contact to shred the cartridge or the hardener tube, resulting in an unmixed portion of resin.

Jan 1, 2003

By T. P. Mucho

Mine roof failure due to excessive horizontal stress has been recognized as a major cause of hazardous roof conditions in some mines. Stress measurements gathered by the U.S. Bureau of Mines (USBM) at 24 different eastern mines show horizontal stress to be typically 2 to 3 times as great as vertical stress. The focus of current Bureau work is to develop detailed design parameters to assess and control the effects of horizontal stress. To facilitate the recognition of horizontal stress effects and to easily determine principal stress direction without resorting to cumbersome, expensive, and time consuming field measurements, the Bureau has developed a stress mapping methodology. Stress recognition and direction determination are required to successfully employ a number of control strategies such as mine layout, mining sequences, and support optimization to control the effects of horizontal stress, thereby increasing the safety of U.S. coal mines. This approach has been used in other major coal producing countries, most notably Australia and the UK, and has greatly enhanced the safety of their mines (1). This paper discusses horizontal stress, directional based control techniques, and provides guidelines for the use of the stress mapping technique. A case study of a mine where the technique has been used is also presented.

Jan 1, 1994

By A. Wahab Khair

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By Duk-Won Park

The excavation of a longwall panel causes a continuous stress redistribution in the surrounding strata for every face advancement. The understanding of the behavior of rock to high level of stresses is instrumental to the structural design of underground mines. In order to achieve a realistic analysis of the behavior of strata, the three-dimensional finite element method is frequently used. Also the model developed for the analysis has to be designed large enough to represent the influenced strata in the study area and a sufficient number of elements has to be used to provide detailed information on the stresses and displacements. Due to the size of the model and its numerical solution the CRAY X-MP/24 supercomputer has been used for this study. The mine site selected for the analysis is a coal mine located in the Black Warrior Basin in Alabama. The mine has two longwall sections at a depth of 2,000 feet with various dimensions of chain pillars, including yield pillars. Various research programs at this mine have been carried out by Park et. al. ( 1984 ). Therefore data were already available on the geology, and physical properties of rock and coal. In addition a rock testing program has been carried out to obtain rock mass classification parameters. The progressive failure technique has been utilized to simulate stress redistributions. The failure criterion after Hoek and Brown ( 1980 ) which is based on rock mass behavior was used for the iterative technique. Simulated stress redistributions are therefore very realistic. In order to automate the process involved in the application of progressive failure technique, a computer program has been developed. The combination of a large scale three-dimensional finite element model and the automation of progressive failure simulation provided a tool that can generate a large amount of information related to the behavior of rock and coal as a response to a longwall mining operation.

Jan 1, 1989

By Hamid Maleki

Results of geologic investigations, in-mine instrumentation, and numerical modeling are presented for two longwall mines in which pillars with large width-to-height ratios (8 to 9) are used. These investigations revealed that wide pillars unload when subjected to sufficient stress and that pillar unloading is influenced by geologic conditions. Field measurements in mine 1 clearly indicated load transfer from the longwall area toward the gate roads, resulting in pillar failure near the margin of a fluvial channel. Loads were shown to transfer to a harrier pillar (width height ratio equal to 9), contributing to progressive failure of this pillar. Unloading of the barrier pillar was associated with significant load transfer to the two-seam submains to the north of the harrier, contributing to roof falls, floor heave, and rib spalling within the submains. Stress analysis results addressed pillar peak strength and unloading behavior that was in agreement with the measurements and underground observations. Underground observations and stress analyses were completed before and after longwall mining near a six-entry submain in mine 2. This submain was intended to he used as a temporary bleeder and tailgate for a small longwall block consisting of one to two panels, depending on the development schedule in other areas of the trine and observed ground conditions. Numerical modeling using both elastic and inelastic pillar behavior for submain pillars with a width-to-height ratio of 8 was completed before mining began. Results indicated that pillar unloading was likely. During retreat of the first longwall panel, pillars unloaded. as evidenced by progressive rib spalling along the cleats, This behavior was mostly confined to the immediate face area, an observation that was in agreement with the modeling results,

Jan 1, 2000

By David Bigby, Tim Ross, David Conover

"Extensive arrays of telltale roof monitoring instruments were recently installed in a Mexican copper mine and a large underground mined storage facility in the eastern U.S. The data were used to evaluate roof stability during development and retreat mining and after installation of supplemental supports. Both manual-reading and automated systems were employed and consisted of up to 64 instruments. This paper will discuss the practical issues involved with installation and monitoring, including reliability and maintenance. Examples will be given for telltale response in relation to known events affecting roof stability, including nearby pillar extraction roof caving, installation of supplemental cable bolts, and separation of the immediate roof layer. The strategy for processing the large quantity of data, presenting the data for review, monitoring the system remotely, and identifying and reporting critical events will be described.INTRODUCTIONTelltales have been used for many years with many varied applications. They are relatively inexpensive, easy to install and interpret, robust, and adaptable. The term ""telltale"" generally denotes a strata extensometer that incorporates a visual indication (and warning) of strata movement. The most common dual-height telltale (Figure 1) was developed by British Coal in the early 1990s as roof bolting was replacing steel arch support (Bigby, 2001). Dual-height telltales provide immediately visible measurements, distinguish between movements above and below the bolted height, and are an established means for providing preemptive warnings of roof falls.Many improvements and modifications on the basic design have been developed to adapt to different mining conditions. For example, triple-height telltales are commonly used where roof bolts of different lengths are installed. The standard manuallyread telltales are limited by the difficulty of obtaining frequent, consistent, and accurate readings, especially in high openings. The instruments may also be located in unstable or inaccessible areas. Consequently, an intrinsically safe electronic telltale system was developed that combines high accuracy and both local and remote reading options. The system supports a network of up to 100 dualheight telltales on each of four separate branches. The instruments are connected with a two-conductor cable and can be read both underground, using a portable readout, and on a surface computer (Figure 2). The automated system still provides the visual warning indication underground."

Jan 1, 2010

By R. Karl Zipf

Highwall mining is an important coal mining method. Upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mine Safety and Health Administration (MSHA) accident data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwail miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Trapped highwall miners present a safety hazard to workers during their recovery. Best practices to avoid trapped highwall miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system, Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

Jan 1, 2004

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013