Search Documents

By Gregory E. Smith

"Tensionable headed roof bolt systems are common in the U.S. mining industry. In the last 15 years or so, they have made a comeback as a hybrid system where a mechanical anchor is used in conjunction with resin. When such a system is used, it is common to use a spherical washer to comply with the requirements of 30 CFR Part 75.204(f)(8). This standard requires an angle-compensating device be used in installations where the bearing plate is offset from the roof bolt axis by an angle greater than five degrees. This paper evaluates system performance of four different traditional angle-compensating device/plate combinations including a new patented extruded plate/extruded washer system that improves overall load capacity and stretch.INTRODUCTIONA large western U.S. underground coal mine was using a fully grouted headed rebar system as their primary support. They had developed their component specifications over many years of working with suppliers to improve and optimize these components to integrate well as a system. As shown in Figure 1, the components included a patented 7 /8"" -diameter Grade 60 headed rebar bolt with a flange capable of full bar load (Walker, 2009) and a patented 8 in x 8 in Grade 3 extruded hole bearing plate manufactured by DieMatic Corporation.The mine decided to pursue a fully grouted tensionable system using a mechanical anchor as the tensioning device. Their primary goal was to eliminate the need for the roof bolt operator to secure (hold) the bolt during resin set time. An additional benefit was the increased initial tension on the bolt. To comply with the requirements of 30 CFR Part 75.204(f)(8), regarding tensioned roof bolts, they were required to include an angle-compensating device because a share of the bolt population would be installed at angles greater than five degrees from the perpendicular to the bearing plate. Also, to improve cycle time and torque/tension consistency, the mine desired to have the washers and anchors assembled at the factory. This required the use of a bearing plate with a center hole large enough to accommodate the 1-3/8-in-diameter mechanical anchor to pass though it during assembly by the roof bolt operator. The mine wanted to continue to use an extruded hole bearing plate in the tensionable system, and EMS was asked to propose a plate and angle-compensating device."

Jan 1, 2016

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Gabriel S. Esterhuizen

The design of support for underground excavations is a complex process in which the interaction between supports and the rock mass must be evaluated. The strength reduction method (SRM) is useful because it provides a stability factor of the supported excavation that can easily be compared between support alternatives. The method is based on numerical model analysis where the stability factor is determined by reducing the rock mass strength until collapse is indicated in the model. This paper presents the results of validation studies that were conducted using the FLAC3D stress analysis software to compare SRMcalculated stability factors to the empirically based Coal Mine Roof Rating (CMRR) and the Analysis of Roof Bolt Systems (ARBS). The objective was to determine whether the SRM, with its basis in mechanics, would predict similar outcomes as the fundamentally different ARBS and CMRR methods with their basis in empirical observations. A total of 450 different scenarios were evaluated in which the geology, horizontal stress, depth of cover, entry width, support spacing, and support length were varied. The results showed that the SRM-calculated stability factors were able to satisfactorily capture both the ?weak bed? and ?strong bed? adjustments in the CMRR. The SRM results were found to be well correlated to the ARBS stability factors for the 450 cases considered. Further analysis showed that the SRM accurately captures the effect of bolt length, depth of cover, and entry width on the overall stability of an entry.

Jan 1, 2013

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy's gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Yvette Heritage

"The risk of fatalities from rib failure is still prevalent in the coal mining industry. This risk has prompted further research to be conducted on rib deformation in order to understand the mechanisms of rib failure, with the long-term objective being to improve rib support design. This paper presents the results of ACARP research project C25057, which investigated the mechanics and drivers of rib failure. The results of rib deformation monitoring at three different mines in Australia provides rib deformation characteristics for overburden depths ranging from 160 m to 530 m. Monitoring includes deformation during development drivage conditions and during the longwall retreat abutment stress environment. The rib deformation monitoring covered three different seams: the Goonyella Middle Seam, Ulan Seam, and Bulli Seam in the Bowen Basin, Western Coalfield, and Southern Coalfield, respectively. The observed mechanisms driving the rib deformation ranged from bedding shear failure along weak claystone bands to vertical shear fractures to kinematic failures driven by shear failure dilation. The variation in mechanisms of rib failure, together with the seemingly consistent method of rib support design, prompts the question: What exactly is the role of rib support?INTRODUCTIONThe current risk of rib fatalities in the coal mining industry has prompted further research into understanding the mechanisms of rib failure. Three Australian mines assisted further research by providing sites for rib deformation studies as part of the Australian Coal Association Research Program (ACARP) project C25057. The mines included in this study were Moranbah North Mine, Ulan West Mine, and Appin Mine. This paper provides key results of the rib deformation monitoring relevant to assessing the mechanisms of rib deformation.The approach of monitoring rib deformation and rib support loads was used to measure and characterise the dynamic rib deformation present in both development and longwall retreat stress environments. The characterisation of rib deformation, together with rock failure modelling, was used to determine the mechanisms for failure within the rib and to assess the interaction of rib support with the failure process. The mechanisms of rock failure are considered an important factor in understanding the drivers for the failure. Consideration of the site-specific failure mechanisms can provide for a more tailored support design."

Jan 1, 2018

By Kazem Oraee-Mirzamani, Nikzad Oraee-Mirzamani, Arash Goodarzi

"Unexpected movement of ground can potentially endanger lives, damage equipment or destroy property. Occupational accidents frequently occur with fatal consequences in developing countries with significant economic dependence on industries such as mining. Therefore, there is increasing need for miners' protection against such hazards. Slope stability and roof support accidents are two of the major causes of fatalities at surface and underground mining operations. According to national codes, employers are obligated to protect workers against accidents; however, these rules fall short of the standards in developed countries. National safety regulations should clearly specify support systems. The International Labor Organization (ILO) prepared two codes of practice, aiming to guide those responsible for improving standards of safety and to provide guidelines for drafting of safety regulations for the coal mine industry and quarry open cast mines. The practical recommendations of these codes in the ground control area have been analysed and the advantages and disadvantages of ILO codes concerning ground control are summarized.INTRODUCTIONTwo million people die every year from work-related accidents and diseases. An estimated 160 million people suffer from work-related diseases, and there are an estimated 270 million fatal and non-fatal work-related accidents per year. In economic terms, the ILO has estimated that 4% of the world's annual GDP is lost as a consequence of occupational diseases and accidents (ILO, 2009).Mining has always been dangerous due to many potential risks such as those associated with using machinery in enclosed spaces, rock falls, blasting operations and explosion of flammable gases, which endanger miners' safety and health. However, it is suggested that implementing new laws along with strict adherence would reduce such risks in the workplace.The severity and frequency of accidents are trending downward in developed countries, where the focus is on large private companies who invest heavily in mechanization and developing economies of scale. But in many parts of the world, particularly in developing countries, minerals are extracted by people working with simple tools and equipment; they work on a smaller scale, are more flexible, and can exploit irregular ore bodies and steep, dipping seams."

Jan 1, 2010

By Karl Jr. Zipf

The famous Homestake gold mine in Lead, SD. closed recently alter 125 years of operation. However, the mine may receive a new lease on life as a National Underground Science Laboratory (NUSL) supported by the National Science Foundation (NSF) and dedicated to high-energy physics experiments involving neutrinos. These experiments require the construction of many large underground chambers tells of meters wide at depths of over 21 18 m. Construction of such large openings at such extreme depths has few precedents m civil-engineering-type construction. The Spokane Research Laboratory has a long history of ground control research at the Homestake Mine and has supported NSF and the physics community in their efforts to develop a NUSL at I Homestake or other suitable location. This paper will summarize underground science and describe proposed underground science laboratories ill the United States, in particular tile proposed NUSL at Homestake. Next, the paper describes an empirical design approach using the Q system of rock mass classification for these large Openings. .M initial site investigation that produced three good case histories is described. The actual support system used at the three sites agrees well with support recommendations from current support design charts, giving credibility to estimates of the classification parameters and Q. Feasibility of, and support requirements for, 25-, 50-, and 100-m spans arc estimated in the anticipated rock mass. This analysis indicates that 25- and 50-m spans are probably feasible, but a stable 100-nn span may be unachievable. The empirical predictions are then compared to detailed numerical analyses. The paper concludes with preliminary support recommendations and necessary site investigations needed to make a proposed NUSL a successful reality. These studies have been important input to NSF for their decisions on the technical feasibility of developing the proposed NUSL. If NUSL is developed, it could enable scientific experiments in areas beyond high-energy physics. 'the laboratory could also enable research in rock mechanics. ground water hydrology. mining engineering, nine safety and health, and ground control.

Jan 1, 2002

By Bob Coutts, Matt Martin, Dan Lynch, Dan Payne

"The Broadmeadow punch longwall coal mine in Central Queensland Australia has experienced significant highwall movement associated with the effect of longwall subsidence when the longwalls approach their final position close to the open-cut highwall. In response to this movement, Broadmeadow employed two types of broadscale highwall monitoring (radar and laser scanners) to provide full coverage measurement throughout three consecutive longwalls approaching the highwall. This was to attain a better understanding of the mechanism causing the movement and potentially enable prediction of instability. Results from the monitoring found the highwall is displaced to magnitudes unlike those typically measured in open-cut mining and in direct contrast with typical longwall subsidence behaviour.This paper discusses the ground movements measured, monitoring methods used, safety measures established, as well as theorising the failure mechanism. Recommendations are made for mine and pit designs for future punch longwall layouts. The paper shows how the movements measured are more aligned to some measurements made during stream valley closure studies previously presented at the ICGCM and challenge the mechanisms suggested by previous literature.BACKGROUNDThe mining of longwalls under or adjacent to large voids (e.g., stream valleys, escarpments, or cliffs) is commonly associated with heavily vegetated or steep surface areas. In areas of extreme topographic variance, access to traditional survey pegs and stations or even new radar or laser technologies is limited. In addition, seldom have the longwall layouts aligned themselves parallel or perpendicular to the surface feature, making interpretation of any available surface movement data more complicated.The punch longwall layout (Figure 1) is also quite uncommon (only undertaken at a small number of longwall mines in Australia) but creates the perfect configuration to enable a somewhat controlled study of the effect of longwall subsidence on a steeply dipping surface feature (an un-vegetated, evenly excavated open-cut highwall). The relatively recently developed radar and laser scanning technology has also enabled near continuous, real-time, sub-millimetre monitoring of a full 500m wide x 100m high highwall. Because the punch longwall enables access and a clear view, the technology could be easily deployed as compared to the highly vegetated and variable topography of stream valleys."

Jan 1, 2018

By Behdeen Oraee-Mirzamani

Tunnel stability has an important role in the production process of an underground coal mine. There are various methods for analysing tunnel stability, such as numerical methods and analytical methods. In this paper, numerical methods (Phase2 software) have been used to determine tunnel wall displacement in a mining tunnel of the Parvade underground coal mine. The Ground Reaction Curve has also been drawn using analytical methods to determine tunnel wall displacement. The comparison of results from the numerical method and the analytical method show a noteworthy difference in the tunnel wall displacement. The displacement calculated by the numerical method shows a lower value than that of the analytical method because the numerical method is more suited to modeling the various coal and rock layers, as well as the shape of the excavations found in coal mines. The methodology used in this paper together with the results obtained from both methods can serve as useful tools for the coal mine design engineer when determining the ground support requirements.

Jan 1, 2013

By M. Afsari Nejad

A Transversely Elasto-Plastic Model was configured in FLAC (Fact Lagrangian Analysis of Continua) as a more realistic simulation of stratified and inclined strata behaviour examining surface subsidence above the inclined longwall panels (I ). The failure criterion employed was a modified Mohr-Coulomb failure criterion that assumed a variable cohesion, which changed with respect to the orientation of the plane of anisotropy . Using the proposed numerical modelling technique several longwall panels with different configurations were simulated. The results of both surface subsidence and horizontal displacements were validated against UK data using the Subsidence Engineer's Handbook (S.E.H) subsidence prediction method and the Influence Function Method (2). It was found from the research that the incite properties as well as laboratory to field reduction factors arc depth dependent. A set of relationships for calculation of anicotropic stiffness and strength parameters have been derived. The proposed modelling approach has been successfully applied to surface subsidence prediction for 3 collieries in the UK allowing the results of the simulation to he validated directly against measured data.

Jan 1, 1998

Roof conditions at Southern Colliery, the second Iongwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 m thick roof beam either bonded or detached, with either a 2 m or 5 m overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

By Klaus Opolony

The German coal industry operates a multi-seam extraction system, with average working depths currently around 1,000 meters. The gate roads serving the longwalls are often used for a second time - a practice which has the advantage of allowing several panels to be extracted with a minimum of roadway drivage work. This preference for re-using gate roads is based on a number of factors: such an arrangement a) prevents the strata pressures in the subsequent panels from being adversely affected by the presence of support pillars, b) helps achieve the target of full mineral extraction and c) allows the roadways to be used for air conditioning and ventilation purposes as part of an advancing longwall system. This paper explains the planning procedure required for a rectangular rockbolted roadway, using as an example a gate road in the 3 meter-thick D2/C seam at Lippe colliery, and describes the subsequent operating experience. Here special attention is focused on modem procedures and techniques for mine roadway planning. The investigation also examines the part played by the mine ventilation system and the available machine technology, which are particularly important parameters for the design of the T-junction areas and support system. Keywords: multiple seam extraction, longwall mining, roadway drivage, roof bolting, roadside pack system, hydraulic frame type support.

Jan 1, 2002

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

By C. Srinivasan

Microseismic emissions are generated by deformation and cracking of rock around an opening inside a mine. The rock tends to achieve equilibrium in a new geometry under changing stress conditions was found to provide useful clues to the impending roof falls and ground instability. The typical characteristics of these microseismic event patterns is shown to be of diagnostic value in sensing in advance rook fall that invariably follow such events. In most of the longwall faces, the main problem faced was due to strata behavior in the presence of massive sandstone bed, which is generally difficult to cave. Microseismic monitoring system was used to monitor strata behavior during longwall mining operation at Rajendra underground coal mine of South Eastern Coal Fields limited (SECL). More than 44,000 microseismic events with local magnitude between -3.4 and 0.5 were recorded during the monitoring period from September, 2001 to March 2003. Analysis of these events was correlated with respect to roof falls. The time series of range of source parameters such as Radiated energy, seismic moment, Energy Index, Seismic Schmidt number, time of occurrence and location of fractures before and during roof fall exhibit qualitatively distinct patterns about six hours before roof falls. &ong the several seismic parameters investigated the microseismic event rate as precursor was found to be most significant indicator of an impending roof fall. The results are discussed as case study in this paper.

Jan 1, 2005

By David C. Oyler

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation, topping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented,

Jan 1, 2001

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By Kourosh Shahriar, Kazem Oraee, Ezzeddin Bakhtavar

"In this paper, a relationship between dependant parameters and the crown pillar thickness is first introduced. This relationship defines geotechnical problems caused by thin pillars and economic considerations created by pillars that are thicker than the optimum size. For this purpose, a dimensional analysis as an effective physico-mathematical tool was used. This technique restructures the original dimensional variables of a problem into a set of dimensionless products using the constraints imposed upon them by their dimensions. A model is hence introduced that calculates the optimum pillar thickness. The relationship introduced here and the method applied can be used by mining engineers in all situations where a combined open-pit and block caving method is deemed to be the most appropriate mining method.INTRODUCTIONMany deposits can be mined entirely with the open-pit method; others must be worked underground from the very beginning. In addition, there are the near-surface deposits with considerable vertical extent. Although they are initially exploited by the open pit method, there is often a ""transition depth"" where decision has to be made about changing to underground methods.Some of the biggest open-pit mines worldwide will reach their final pit limits in the next 10 to 15 years. Furthermore, there are many mines planning to change from open-pit to underground mining due to increasing extraction depths and environmental requirements. In this way, it is likely that block and/or panel caving will enable the operations to continue achieving a high production rate at low costs as an underground method (Bakhtavar et al., 2009).In these cases, it is often necessary to consider a crown pillar beneath the transition depth (open-pit floor) before starting an underground caving stope method (Figure 1).There are generally two kinds of crown pillar: a ""surface crown pillar"" and ""crown pillar between open-pit and underground mining."" In general, they both play the similar role in mining. Since the primary purpose of a surface crown pillar is to protect surface land users, the mine, and those working in it from inflows of water, soil, and rock; it is vital that the surface crown pillars remain stable throughout their life. When a crown pillar could potentially remain between open-pit and underground mining it is specially proposed to prevent water entering from the open-pit floor into the stope, as well as to reduce open-pit wall and floor caving."

Jan 1, 2010

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002