Search Documents

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Liang Dong, Jinxuan Liu, Biao Qiu, Jing Chai

"The Cenozoic unconsolidated strata in the east area of China are composed of clay, sandy clay, fine sand, hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged in various degrees since 1987. The main reason for this disaster is the vertical additional stress on shaft caused by the subsidence of the thick unconsolidated strata. In order to monitor the subsidence deformation of the unconsolidated strata, a sensing network system with multiplexed Fiber Bragg Grating (FBG) for monitoring settlement deformation of the unconsolidated strata in deep borehole is proposed. The field monitoring results show that, soil layers settle or expand with decrease or increase in ground water levels. The thick hardpan generates the main compressive deformation. This FBG strain monitoring method can take place of traditional ground water measuring method. This system is stable and reliable, and the monitoring results can show the subsidence deformation of different layers, which has significance for the predictive maintenance of the shafts.INTRODUCTIONSince 1980s, a specific geologic hazard has occurred frequently on the coal mine shafts in eastern China: non-mining-induced shaft deformation, involving up to 100 shafts located in Jiangsu, Shandong, Anhui and Herran province, distributed in Xuzhou, Datun, Huainan, Huaibei, Yanzhou and Yongxia coal fields. This kind of geologic hazard can lead to shaft wall deformation, water infiltration, cage stuck, water-sand burst or shutting down of coal mines, which seriously risks the coal mines. Zhangshuanglou coal mine, Haizi coal mine and Linhuan coal mine shut down for 2-8 months due to this hazard (Chen, 1997; Cui, 1998). The main reason for this geologic hazard is the subsidence of the super thick unconsolidated strata (Liu et al., 2007; Xu et al., 2006).An innovative structure health ·monitoring and damage estimation method has been developed in recent years, i.e., optical fiber smart material and structure (Nobuo, 2002; Wang et al., 2000). A Fiber Bragg grating (FBG) sensor is a device that can transfer the change of the measured strain or temperature to the change of Bragg wavelength. One of the most important applications of FBG sensors is to monitor the internal stress and strain distribution of material and structure (Philipp et al., 2000; Ansari et al., 1998). Compared to traditional electrical sensors, FBG sensors have many advantages; they are adaptable to harsh environments, abrasion resistant, immune to electrical magnetism (EM) interference, safe and reliable. They also offer integrated sensing and transmission on a single fiber, have simple structure and are convenient to use, which satisfies the requirements of long distance, distributional and long term use in monitoring mining and geotechnical engineering structure. Due to such advantages, the FBG sensor has already been applied in petroleum engineering (Kersey, 2000), rock mechanics testing (Cornelia et al., 2003; Yang et al., 2007; Wei et al., 2008), physical simulation experiments (Chai et al., 2007; Chai et al., 2006; Zhu et al., 2008; Li et al., 2008; Chang et al., 2008), strain sensor (Li et al., 2007; Chai et al., 2008) and construction structure damage diagnosis (Dong et al., 2004; Kerrouche et al., 2008; Whitten et al., 2001)."

Jan 1, 2010

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Hongwei Zhang, Sen Yang, Shimin Liu

"This laboratory study investigates the damage evolution of sandstone specimens under two types of cyclic loading conditions through monitoring and analyzing the variations of elastic moduli and ultrasonic velocities. We adopted the rigidity degradation method for evaluating the damage accumulation through the rock dynamic ultrasonic velocity measurements. Compared to the ultrasonic test, the method of rigidity degradation shows deficiencies in the detection of damage development. The cyclic loading within the elastic limit led to a stiffening trend for the loading process but a softening trend for unloading process. The method of rigidity degradation was unable to describe the damage accumulation in this situation, while P-wave velocity clearly reflected the damage development. Moreover, a simplified model is established for interpreting the behaviors of the modulus variations and ultrasonic velocity. The cyclic loading within elastic limit enhances the anisotropy of rock, which causes a denser packing pattern in the direction of axial stress. The persistent damage accumulation under the cycling with an increasing upper limit is the consequence of the tensile failure in the microstructure of sandstone. INTRODUCTION The damage accumulation due to dynamic (cyclic) loading is highly detrimental in many engineering structures, such as mine openings, petroleum and natural gas boreholes, tunnels, rock foundations, and underground chambers. The sources of cyclic or repetitive loadings can be roughly divided into two types: (1) periodic operation, including drilling, blasting, and mining; (2) random vibration, including earthquakes and traffic loads. The repetitive loading-unloading process opens and closes the micro-pores and micro-cracks within the rock, further inducing the growth of cracks. As expected, the accumulating damage becomes a potential factor to trigger the rapid and violent failures of large-scale engineering rock structure."

Jan 1, 2017

By Andre Cezar Zingano

"The empirical approach for pillar design assumes that geological conditions should be perfect, such as horizontal seams, and that pillar strength and behavior will only depend on the coal seam strength and the vertical pressure caused by the overburden thickness on the coal seam; this vertical pressure is based on the tributary area. Empirical methods do not consider the effect of the interface between the roof and pillar or the floor and pillar.The effect of the interface shear strength on final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 meters). This case study involves a mining section at the 101 coal mine in the Santa Catarina state of Brazil, which is experiencing pillar rib spalling and yielding because of a 1-to 2-cm-thick clay layer at the area of contact between the coal seam and immediate roof. The depth of the coal seam is 60 m on average and 2.3 m in height. This particular section also has 12-14% (7-8°) of seam inclination. The pillar size varies from l lxll to 13xl2m; thus, the safety factor (SF) based on the ARMPS approach is more than 1.5. The objective of this paper is to determine the cause of the pillar yielding and study the effect of the clay layer at the interface between the roof and pillar, including the inclination of the coal seam. This study conducted empirical and numerical models (2D and 3D) to understand the effect of the thin clay layer. The conclusion is that the clay layer affected the strength of the interface between roof and pillar, causing rib spalling and reducing the pillar strength.INTRODUCTIONPillar stability and deformation depends on the coal seam strength and vertical pressure caused by the overburden thickness on the coal seam, and this vertical pressure is based on the tributary area. The effect of the interface shear strength on the final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 m). This interface could be represented by a thin clay layer or an abrupt contact between the coal seam and a rigid sandstone layer of the immediate roof. These two interface conditions are found in the coal mines of Brazil, and the effect of the interface shear strength could increase when the seam's inclination is higher."

Jan 1, 2016

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Gang Ren, Behrooz Ghabraie

"Observational data suggest that the ground surface subsidence profile from multiple-seam longwall mining is rather different from that of single seam. Despite the increase of coal production from multiple-seam mining, available predictive methods are mostly unable to predict a reliable subsidence profile for multiple-seam extractions. In this paper, a case study of multiple-seam subsidence is modelled using physical modelling techniques. The subsidence mechanism as revealed in the physical model is explained and the differences between multiple and single-seam subsidence are highlighted. On the same case study, a commonly used influence function method (IFM) and Generalised Influence Function Method (GIFM) are utilised to predict the subsidence profile. The results are compared with predictions achieved by a newly developed predictive method based on the understanding of mechanism of the multiple-seam subsidence. Results show a significantly improved correlation between the newly developed method in comparison with the conventional IFM and GIFM. INTRODUCTIONField observations and subsidence monitoring data from multiple-seam coal mining cases show a different subsidence profile as compared with single-seam ones (Sheorey et al., 2000; Li, et al, 2007; Luo and Qiu, 2012; Unlu et al, 2013). The multiple-seam subsidence curve is generally deeper and steeper than of single-seam cases, and varies from one mining configuration to another. Various researchers had made efforts to understand the mechanism behind this phenomenon and the interaction between the two mining horizons (Li et al., 2010, Sui et al., 2014; Zhang et al., 2014). However, the mechanism of the multiple-seam subsidence is yet to be comprehensively understood (Suchowerska, 2014; Ghabraie et al., 2015b).In addition, differences between the single and multiple-seam subsidence profiles make it difficult to adapt single-seam subsidence prediction tools for predicting the subsidence over multiple-seam cases, unless significant modifications are applied This requires understanding the mechanism of the multiple-seam subsidence as the first step to achieve reliable predictive results.The mechanism of the subsidence due to a multiple-seam case study can be investigated via physical modelling. The physical model allows observing the substrata movement as well as the interaction of the two mining activities. An understanding of the mechanism of the multiple-seam subsidence can be developed based on these observations, which would provide basis for developing a subsidence prediction tool."

Jan 1, 2016

By Peter Zhang, Dan Neilans, Scott Peterson, Scott Wade, Joe Pugh, Ryan Mcgrady

"A coal outburst is a severe safety hazard in room-and-pillar mining under deep cover. It is more likely to occur during pillar retreating. Multi-seam mining dramatically increases the risk of coal outburst within the influence zones created by remnant pillars and gob-solid boundaries. Though coal outburst is generally associated with heavy loading of coal pillars, its occurrence is difficult to predict. Risk management provides a proactive tool to minimize coal outburst in room-and-pillar mining under deep cover. Risk assessment is the first step in identifying and quantifying outburst risk factors. The primary risk factors for coal outburst are overburden depth, roof and floor strength, geological anomalies, mining type, multi-seam mining, and panel width. A risk assessment chart can be used to proactively screen out mining sections with high risk of coal outburst for further analysis. Gob-solid boundaries and remnant pillars are critical factors in evaluation of the coal outburst risk of multi-seam mining. Risk identification, risk assessment, geologic influence mapping, geotechnical evaluation, risk analysis, risk mitigation, and monitoring are essential elements of coal outburst risk management process. Training is an integral part of risk management for risk identification and communication between all the stakeholders including management, technical and safety personnel, and miners.INTRODUCTIONA coal outburst is a sudden violent burst of coal from a pillar with broken coal or blocks of coal forcibly ejected into open entries. A coal outburst is a severe safety hazard as the mining crew is highly exposed at the site when the event occurs. Though deep cover and strong roof and floor are underlying geologic conditions of a potential burst incident, its real occurrence is also the result of additional mining factors. In room-and-pillar mining, a coal outburst could occur during both development and pillar retreating, but the latter greatly increases the risk of outburst. The other risk factors of coal outburst also include mining layout, multi-seam mining, presence of adjacent gob, cutting sequence, and local abnormal geologic conditions. Over the years, the cases of coal outbursts have been studied by many researchers and mining practitioners(Peng, 2008; Newman, 2008; Iannacchione and Tadolini, 2008; Gauna and Phillipson, 2008; Hoelle, 2008; and Newman, 2002). It is commonly believed that the coal outburst is the result of a sudden release of elastic strain energy stored in coal pillars and is highly associated with cutting into heavily loaded coal pillars, but its occurrence is a rare event and is difficult to predict. A number of engineering controls have been recommended to mitigate outburst potential. For room-and-pillar mining, sufficient pillar sizes have been the primary control for coal outburst prevention. The pillar design tools such as ARMPS and AMSS developed by NIOSH have played an important role in the design of stable pillars to prevent pillar collapse and squeezing as well as coal outbursts. In fact, with the implementation of pillar design using proper stability factors, pillar collapse and squeezing have been almost eliminated, and the number of coal outbursts has been greatly reduced in the US over the past decade. However, after a few outbursts occurred during pillar retreating in the US over the past a few years (MSHA, 1996; MSHA, 2014; MSHA, 2013), it has been realized that sufficient pillar size is still not enough to prevent coal outbursts. The investigations of the incidents showed that other factors such as multi-seam mining, panel layout, cutting sequence, and local geologic factors also seemed critical in causing the events. Therefore, it has become imperative that additional proactive measures beyond proper pillar design be implemented to prevent coal outbursts."

Jan 1, 2015

By Zach G. Agioutantis

The Illinois Basin has an extensive history with the use of mechanized longwall mining dating back to the early 1970?s. In recent times, technological advances have resulted in increased panel widths from 800 feet to over 1400 feet and daily panel advance rates have also increased significant l. The prediction and control of subsidence and surface deformation due to underground mining are important considerations in the permitting, planning, and monitoring of these coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology, well utilized in the Illinois basin, and widely used by researchers and planning engineers around the world. This paper utilizes subsidence data, recently measured in longwall operations in Illinois, to develop an updated ground movement prediction capability implemented by the Surface Deformation Prediction System (SDPS) software package.

Jan 1, 2014

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By Yi Luo

Subsurface strata movements and deformations associated with underground mining activities could cause problems to subsurface structures and water bodies. By incorporating the methods for surface subsidence prediction with the subsidence parameters derived from collected subsurface subsidence data, methods have been proposed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining. Two new' types of strata deformations in the field of subsidence research, vertical and total strains that could he useful in assessing subsidence influences to the subsurface structures and water bodies, have peen introduced.

Jan 1, 2000

By Kot Unrug

For the purposes of underground mine design, twelve cores of the Springfield (V) Coal (Pennsylvanian) roof and floor were retrieved. Each core was photographed, described fresh in the barrel, and the rock quality designation (RQD) was measured. Cores were wrapped in plastic and delivered to the rock mechanics lab. At the lab RQD was remeasured and new photographs were taken before running geotechnical tests including weatherability. Significant differences in barrel RQD's vs. lab RQD's have been noticed in spite of careful handling. The drill site RQD is generally used to calculate geotechnical results, but in some types of coal measure rocks, further fragmentation of core takes place with slight changes of moisture content, which occur even in well wrapped core. This creates a dilemma which RQD should be used for support design. Rocks around excavations are exposed to the significant changes in moisture content due to the seasonal weather changes and related fluctuation of humidity of air ventilating a mine. Therefore, it appears to be more realistic using laboratory RQD which corresponds closer to the actual rock condition around the excavation. Weatherability test, developed for characterization of time dependent behavior of rock exposed to fluctuations in moisture content, is thought to be related to the above-mentioned changes of RQD. In weak shales, mudstones and claystones which weather rapidly, it is essential to characterize their future behavior in the pre-mining stage. This can allow for a realistic design of primary, and particularly secondary support in coal mines, especially in coal fields where such geologic conditions exist.

Jan 1, 2003

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987