Search Documents

By J. Nielen van der Merwe

This investigation was done to develop a method to predict the lie of coal pillars. It has long since been known that coal pillars deteriorate over time, but there was no method to quantify the deterioration. It was found that the rate of pillar deterioration was essentially a function of two parameters, namely mining height and time. The higher the mining height, the more rapidly the pillars deteriorated. The rate of deterioration is not constant, but decreases exponentially with time. The pillar life should be viewed in conjunction with the safety factor. While the relationship between safety factor and pillar life is ambiguous, the trend is nonetheless for higher safety factor pillars to have longer lives. The safety factor can be used to quantify a failure probability. The pillar life prediction indicates when the pillars which are predicted to fail, can be expected to do so.

Jan 1, 1998

By Stephen P. Signer

To improve the understanding of the support interaction mechanics between grouted bolts and coal mine roofs and to help lay the foundations for improved design and evaluation techniques, the 0.8. Bureau of Mines has conducted laboratory, field, and analytical studies of the load transfer mechanics of grouted roof bolts. Mechanisms by which load is transferred from a bolt through the grout to the rock mass are analyzed. Strain gauges were installed on over 70 bolts and tested to observe the rate of load transfer when a force was applied at the bolt head. Laboratory and field tests were conducted to determine bolt-grout- rock interaction behavior in both the elastic and postyield phases. Long-term laboratory tests were run to determine the time-dependent properties of both polyester resin- and-gypsum-grouted bolts. Numerical studies using finite- element techniques were compared to the experimental results. Elastic tests showed that 90 pct of the applied load was transferred within 24 in of bolt length. Long-term tests indicated that creep is more significant in gypsum-grouted bolts than in resin- grouted bolts. Plastic studies showed that yielding of steel will translate down the length of the bolt from 6 to 20 in.

Jan 1, 1988

By Gennaro G. Marino

Documented case histories of surface ground movements from mine subsidence were utilized to help determine when the initial collapse of the overburden occurred above longwall panels. By studying this relationship between initial movement at the surface and the amount of face advance, the least-complex conditions exist for empirically assessing the span capacity of the overburden. The objective of this work was to obtain a better understanding of the overburden response to longwall mining. This knowledge will give a better insight on the long-term effects that different overburden types have on the stability and the subsidence potential of room and pillar mines, as well as, the influence of the overburden on subsidence over longwall panels. Theory on the overburden span capacity was developed and correlated to field observations. Data were used on the overburden lithology, depth, width, and face advance of the panel, and the subsidence conditions that were noted on the surface. The subsidence measured on the surface was used to determine when complete failure in the overburden rock had occurred. According to spans predicted by theory and the subsidence measured in the field, the competent lower units failed at a face advance less than when significant subsidence was observed on the surface. In each case studied, there were competent lower beds; however, the full overburden weight was not sustained to the point of subsidence. The best correlation with the surface movement was found with the most shallow, competent bed. Elastic plate solutions with various support conditions were found to best monitor the surface subsidence of these upper roof units.

Jan 1, 1988

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Thomas M. Barczak

This report examines practical considerations in longwall support selection that have evolved from Bureau of Mines ground control research. The scope of discussion includes trends in support selection, analysis of shield designs, performance testing, and an examination of support and strata interaction theories and their relevance to in situ support loading. Application recommendations are made for two-leg shields. four-leg shields, and chock-shields. Two-leg shields account for 67 pct of the current active longwall installations and are used in a variety of applications. Automated control systems are likely to continue to grow in utilization. The next major change in shield design is likely to be the application of wider supports. The most effective method of performance testing longwall shields is by controlled displacement of the canopy relative to the base. Controlled force application does not control the load transfer through the shield and may not produce maximum loading in all support components. Theories of estimating support capacity based upon a detached roof block that must be maintained in equilibrium by the powered support are being challenged by concepts based upon the equivalent stiffness of the total ground supporting system.

Jan 1, 1990

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

Jan 1, 2006

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Xinzhi Du

Coal strength is essential to analyze the stability of excavation in coal. It is well known that the strength of coal tested in the laboratory is size-dependent, and different size specimens will produce different strength. Many researchers have studied the uniaxial compressive strength of coal and developed a number of empirical formulae to describe the strength variation with specimen size. According to a comprehensive data base that includes most of the laboratory testing results in the last century in U.S. and South Africa, the size effect and shape effect were reviewed and analyzed. The results show that different groups of coal specimens have different size effect on the compressive strength. The critical size for the size effect from the data analysis is about 40 in. The shape (W/H) of the specimens has a large effect on the compressive strength. The pillar strength formulae obtained from the data regression have a larger strength than all other existing formulae. Most pillar strength formulae have their own place in coal pillar design field. In order to analyze the difference of those formulae, twelve design formulae have been selected to compare using the Pittsburgh coal seam. The intention is not to determine the preferred formulae, but only to compare them, and see how do the W/H ratio, width, length, angle, cross-section area and effective width affect different pillar strength formulae?

Jan 1, 2008

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By Karl Zipf

In highwall mining, once a sufficient number of web pillars are developed, they can fail catastrophically in a domino-type failure, posing a safety hazard to highwall miners and sterilizing mineable reserves. Three recent case histories of catastrophic web pillar failure in U.S. and Australian mines are documented and analyzed with two design approaches. The conventional design approach uses only a strength criterion, while the postfailure design approach uses both strength and stability criteria to insure an acceptable failure mode should strength failure occur. Catastrophic highwall web pillar failures can cost money through equipment losses, production losses, coal reserve sterilization and lost opportunity costs. Coal recovery may be higher. but the benefits of higher recovery must balance the potential costs of failure. Application of the conventional or postfailure design approach will decrease coal recovery and revenues, but the risk of potentially costly failure is much less.

Jan 1, 1999

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

In this paper, the authors attempt to apply a simplified non-homogeneous void diffusion model (NHVDM) to predict surface subsidence for longwall mining in Illinois. A generalized error function subsidence profile is derived from this model. The model validation indicates that the NHVDM approach appears to fit the observed subsidence data as well or better than the error and the trigonometric functions, particularly around the trough edge areas.

Jan 1, 1990

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By Stephen C. Tadolini, Peter A. Gray, Robert Hawker, Andrew Sykes

"Self-drilling rock bolts (SDRBs) that use pumpable cement grout to anchor bolts have been used successfully in the tunnelling and civil engineering industries for many years. Pumpable cement grout offers a considerable advantage in that the SDRB can be fully encapsulated right down to the bearing plate, including filling cracks and cavities in the borehole. However, cement grout cannot provide the immediate rock support required for the coal industry. This paper describes a new SDRB system that uses pumpable resin to anchor the SDRB in a borehole, which not only provides all the advantages of a pumpable grout anchoring system, but also provides immediate roof and rib support as required in the coal industry. This paper further outlines the latest developments in SDRB technology including (1) extendable self-drilling rock bolts, which can almost double in length during the installation process and are particularly suited to low seam heights and rib support and (2) pre-tensioned SDRBs, where a pre-tensioned load can be applied during the installation process. These new SDRB systems offer both considerable advantages in rock support and improvements in mining productivity.INTRODUCTIONThe mining industry is continually striving to develop more efficient methods to support the roof and walls of roadways and tunnels, and rock bolting has proven to be one of the most significant improvements in ground support over the last 50 years. Rock bolting is now almost universally used in the underground mining industry worldwide, and there are many different rock bolts available.Rock bolts are traditionally made from steel or fiberglass and are anchored into a borehole with a friction-anchoring device, such as an expansion shell mechanism; cement grout; or chemical resin. Friction-anchored bolts are widely used in the Australian metal mining industry, predominantly as short-term support. They are used in conjunction with resin-anchored bolts where there is a requirement for longer life. Resin-anchored bolts are used in the coal mining industry.Friction-anchored bolts provide immediate rock support, but their load transfer capacity is poor compared to resin or cement anchored bolts. In addition, friction-anchored bolts are more susceptible to corrosion than resin or cement anchored bolts."

Jan 1, 2010

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998