Search Documents

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By Verya Nasri

The Silver Line Phase III Project is the final one mile underground segment of the new Bus Rapid Transit in downtown Boston. The project is expected to significantly reduce existing and anticipated traffic congestion. The twin one-lane tunnels and two station platforms will be built by NATM in Boston saturated soft clay, sand and till layers in proximity to several historical buildings, underpinning two existing cut and cover subway stations and several major utilities in densely built urban area. This paper presents the analysis and design of the NATM tunnels and stations detailing the excavation sequence and support system and various ground improvement and pre-support techniques used in the preliminary and final design of the project

By U. Richter

Conveyors are a highly effective means of transporting material over long distances. Recently there has been a trend toward long conveyor systems with high capacity single flights. These conveyor systems are an efficient alternative to costly truck fleets. Also with deeper mines, the use of diesel driven trucks becomes more difficult. Another trend is in underground mining, where conveyors are an efficient alternative to drift hoists or dedicated rail systems.

Jan 1, 2012

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

The Río Agrio of northern Patagonia, Argentina, is highly acidic due to inputs of volcanic gases (SO2, HCl, HF) in its headwaters. The watershed includes a hyper-acidic (pH <0.5) volcanic crater lake, a larger glacially carved lake that is also strongly acidic (pH 2.6 to 2.7) and an acidic river that flows for more than 40 km (25 miles) before its pH is completely neutralized. This unique watershed has many geochemical and biological similarities to acid waters caused by mining. This paper describes the Río Agrio watershed and draws a comparison with some famous acid mine waters. Learning more about naturally acidic lakes and river systems could have important applications to the bioleaching of ores or biological treatment of mine waters. Therefore, it should be of interest to the general community of mining and metallurgical engineers.

Jan 1, 2008

By Paul C. Schmall

The link between artificial ground freezing and the mining industry stretches back more than 140 years, and across an ocean. Patented by the German scientist F.H. Poetsch in 1863, the technique is reported to have first been used circa 1862 in the coal mining valleys of South Wales. In the United States, the first ground freezing application, to a depth of 30 m (100 ft), occurred in 1888 for the Chapin Mine Co. in Iron Mountain, MO. In England in 1901, the Poetsch method was used for the first time to successfully sink two shafts through 24 to 27 m (80 to 90 ft) of wet sand and boulder clay at the Washington Glebe Colliery, near Sunderland. British mining engineer T.H. Cockin, in his 1905 Class-Book of Practical Coal-Mining, noted that, ?This method of sinking through thick beds of very wet quicksand has met with great success; it is one of the recognized methods of sinking on the Continent.? Mine shaft freezing soon became relatively common in Europe where the project could bear the cost of a major refrigeration plant construction. However, it was not until 1952 that the second North American ground freezing project was completed to facilitate the sinking of a 4.5-m- (15-ft-) diameter, 233-m- (765-ft-) deep shaft at a Potash Company of America (PCA) mine in Carlsbad, NM. Nowadays, ground freezing is used worldwide for both mining and civil applications. In small mine shafts of 3 to 6 m (10 to 20 ft) in diameter, excavations have been carried out to depths of more than 820 m (2,700 ft) within the protection of unbraced or unlined frozen walls. In fact, for deep mines, no better method has yet been established for sinking production shafts through deep, water-bearing ground. Major deposits of coal, potash and salt would still be inaccessible if not for artificial ground freezing. There are several advantages of ground freezing unique to the construction of shafts. Proper instrumentation can provide complete assurance of the integrity of the freeze to full depth prior to excavation. The frozen wall allows construction to be scheduled without evaluating the in-shaft time necessary to probe ahead, place additional sup-ports or deal with ground water. The freeze can be implemented perfectly through the soil/rock interface, which is often the most difficult geology in which to create a ground water cutoff by other methods. At increasing depths, any discontinuity

Jan 1, 2007

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By S. Hardcastle

Various controlled and ambient tests were undertaken to evaluate the performance of a variety of digital heat stress monitors, psychrometers and simpler temperature/relative humidity data loggers that measure, or determine, such parameters as: dry-bulb, natural wet-bulb, psychrometric wet-bulb and globe temperatures. In this comparison, funded by the Deep Mining Research Consortium, it has been found that all the instruments can competently measure dry-bulb temperature but the accuracy of other sensors could introduce significant uncertainty. For example the quality of relative humidity sensors and failure to correct for the barometric pressure difference in deep mines, directly impacts upon the calculation of psychrometric wet-bulb. The comparison has shown that the response of dry-bulb and globe temperature sensors can vary widely under different radiant heat conditions; however this would be negligible in most mines. Of more concern is the differing performance of the natural-wet bulb sensors especially at low relative humidity and low air velocity. Furthermore, from these tests and the currently available theory it was not possible to determine if any of the natural-wet bulb instruments measured that value correctly or validate any relationship between psychrometric and natural wet-bulb temperature at low air speeds where their difference is greatest. Consequently the uninformed use of some of the commercially available environmental heat stress monitors or derivations from other instruments could provide erroneous results affecting the work load category that can be accommodated or the rest ratio regime required.

Jan 1, 2009

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By D. H. Horswill

The Red Dog Mine is the world’s largest zinc mine. It is located 145 km (90 miles) north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called the Northwest Alaskan Native Association (NANA) Development Corp. NANA acquired surface and subsurface title to this resource as part of its settlement lands under the Alaska Native Claims Settlement Act. In 1982, NANA entered into a lease agreement with Cominco. Cominco is an international mining company focused on zinc. It built and operates the Red Dog Mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language and traditions are as important to the NANA people today as they were in the past.

Jan 1, 2000

By Gennaro G. Marino

During the preliminary design stages of the Illinois Division of Natural Resources(DNR) building, it was discovered that an old coal mine was present some 70 m (220 ft) beneath the building site. The new DNR building to be constructed is 36 m (120 ft)wide and 134 m (440 ft) long. It has three stories above grade and abasement level. The building is oriented north-south and has east and west ponds next to it (Fig. 1). The building is located on the State Fairgrounds in Springfield, IL. Given the history of surface subsidence of these underground coal mines in the Springfield area, there was concern about the potential for future subsidence at the building site. Mine subsidence events in the area have resulted in more than 0.9 m (3 ft) of settlement and have caused significant structural damage.

Jan 1, 2000

By E. Giama, A. Macridis, A. M. Papadopoulos

ISO 14031 is an international standard that describes a process for measuring environmental performance evaluation by setting quantitative indicators and providing a structured approach for organizations to follow, independent of location, size, complexity and type of activity. It is not a standard for certification as ISO 14001 is, but it fits into the ISO 14000 series of standards and is intended to assist organizations to apply environmental management systems and obtain environmental evaluation. This case study’s main objective is to identify the interaction between ISO 14031 and ISO 14040-42. ISO 14040-42 is referring to Life Cycle Analysis (LCA) methodology. More specific, LCA is applied (based on the ISO 14040-42 standard) to stone wool’s production, the market dominating thermal insulation material, produced by bauxite and amphibolite. LCA is used as a decision making tool for the development of environmental indicators (based on ISO 14031 guidelines) and for environmental performance evaluation.

Jan 1, 2005

By Steve Kral

"Liebherr, as most anyone involved with the global mining industry knows, is one of the world’s largest makers of mining and construction heavy equipment. The familyowned company has been around since the 1940s and, according to Stefan Heissler, by the end of next year, will employ about 44,500 people worldwide. Heissler is a member of the board of directors of Liebherr International AG.It all started for the Switzerland-based company when Hans Liebherr first recognized a need for heavy equipment in the construction industry, Heissler said. His first product, introduced in 1949, was the TK10, a mobile crane that, at the time, was a groundbreaking innovation to the heavy construction industry. From there, the company began its growth into a world-leading heavy equipment manufacturer that always relied on innovation.In October, Liebherr gathered a group of mining and construction magazine editors in Leoben, Austria to take a look at the company’s latest addition to the global mining and construction markets. On the mining side, Liebherr provided a demonstration of its T-236 100-t (110-st) haul truck and the PR- 766 50-st (55-st) crawler tractor. The one-day demonstration took place at the Erzberg iron mine near Leoben, where both machines are being proven.The Erzberg Mine, operated by VA Ersberg, has been in operation for about 1,300 years and is said to be Europe’s largest surface mine. It employs about 230 people and mines about 12 Mt/a (13,200 million stpy) of ore, producing about 3 Mt/a (3.3 million stpy) of fine-grained iron ore.T-236 rigid-frame truckThe new T-236 rigid-frame dump truck, with a diesel electric drive system, is Liebherr’s entry into the 100-t (110-st) class and is the first in this class with a four-corner, oilimmersed braking system. The haul truck was first introduced during the 2016 MinExpo in Las Vegas, NV. The unit has since successfully completed its testing phase and is currently in its first field operation trials at the Erzberg iron mine in Austria."

Jan 12, 2017

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12&apos;-6" diameter Wirth hard rock TBM.

Jan 1, 2005