Search Documents

By J. A. Herbst, C Lo. Y, Z. Rogovin

The identification and quantification of incipient overload conditions in mills have recently been found to be very significant in the design of tumbling grinding mills. To investigate these phenomena, a series of experiments was conducted in a Plexiglas mill operated in both dry and wet modes. For on-stream measurement of the mill charge weight, volumetric filling, dynamic angle of repose, and mill power, an electronic system was developed. The mill was filled to various levels with 19.1-mm (3/4-in.) ceramic balls as grinding media. As feed material, grindable limestone or 3.2-mm (1/8-in.) nongrinding ceramic balls were fed at various steady-state rates to determine the incipient overload conditions. The prediction of overload has apparently been reduced to predicting the feed rate that results in 50% mill filling.

Jan 1, 1988

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By D. P. Patil, T. C. Rao, J. P. Barnwal

Factorial design of column flotation experiments was used to understand the main and interactional effects of the column parameters. In the experiments, the air flog rate, the wash-water, flow rate and the froth depth were varied at two levels. Analysis of the results showed that an increase in airflow rate had a deleterious effect on the grade of the concentrate, whereas, an increase in froth height increased the grade. The interactions between airflow and wash water and between airflow and froth height were significant with respect to grade of the concentrate. These results demonstrated that, from an ore containing 12.76% P2O5, it is possible in a single-stage flotation column to obtain a concentrate containing 31 % P2O5 (10.6% Si02) with a recovery of 94%, thus reducing the number of cleaning stages that would be required if conventional flotation cells were used.

Jan 1, 1997

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By Gill G. Geesey, Michael R. Hankins, Paul L. Wichlacz, Anita Gianotto, John G. Jolley, Randy B. Wright

Thin films of copper [2.0 nm on germanium internal reflection elements (IREs) and 3.4 nm on germanium discs] were exposed to 10% gum arabic (aqueous solution) , 2% alginic acid (aqueous solution), 1% bacterial culture supernatant (BCS, simulated seawater solution) and 0.5% Pseudomonas atlantica exopolymer (simulated seawater solution). The IRES were monitored in situ, in real time using fourier transform infrared/cylindrical internal reflection/attenuated total reflection spectroscopy as a function of time at ambient conditions. The discs were characterized (pre- and post-exposure) by X-ray photoelectron and Auger electron spectroscopies. Ancillary graphite furnace atomic absorption spectroscopy was used to monitor the removal process of the copper thin film from the germanium substrates. Results indicate that Cu was oxidized by gum arabic, alginic acid and BCS. Furthermore, Cu was removed from the Cu/Ge interface by all four polymers. The Cu was found associated with the polymer solutions.

Jan 1, 1989

By A. Balint

The Photometric Optical Separation process is introduced and examples of sorting machines are given. Applications of the process are outlined in general terms with reference to specific types of industrial installations. Brief description is given of the capabilities and limitations of available equipment, including cost estimates.

Jan 1, 1967

By J. J. Webb

At Kerr-McGee's Galatia Mine in southern Illinois, the need for safe and efficient longwall moves prompted a detailed planning effort. Galatia Mine operates two longwalls on separate coal seams with different geologic conditions. An overview of the longwall move planning as related to manpower training, roof control, ventilation, transportation, equipment recovery and setup will be discussed. The impressive safety record achieved during each of the longwall moves at Galatia Mine verifies that health and safety planning does play a major role.

Jan 1, 1994

By Todd S. Harris

Industrial minerals or non-metallic minerals are loosely used terms applied to a diverse assortment of materials which, in many cases, have nothing more in common other than the fact that they are neither metals nor fuel minerals. To help bring order to this otherwise random assortment of minerals, we have grouped these materials into two main categories; chemical and physical minerals, and nine sub-categories based on end-use applications as shown in Table 1. Chemical minerals are products which are principally used for the specific chemical elements they contain, whereas physical minerals are products which are used to meet specific performance specifications. The latter part of the 1970?s, in particular 1978, were considered peak years in terms of production and sales for many industries, By using 1978 as a base year, we can evaluate wherethese markets stand today after the recession of the early 1980's and the recovery which began several years ago. From this historical overview and appraisal of the current situation, various assumptions can be drawn as to which markets are expected to perform well into the 1990's.

Jan 1, 1987

By John T. Awald

The efficiency of search for porphyry copper and molybdenum deposits can be greatly increased. A model exploration system is here presented to show how geologic literature data and field surveys can be aided by modern statistical and computer methods. Assuming that major ore deposits occur in clusters, it is possible to evaluate rapidly large areas at modest cost and with minimum investment risk. An example of the success of these methods is given. Clusters of mine density and metal production covering the State of Nevada were plotted and machine contoured. Selection of a 47,300 square-mile area on the Nevada-California border was made. Within this area, detailed analyses were performed, and a 3000 square-mile site was picked for subsequent field examination. To initiate efficiently the field work, 81 stream sediment geochemical samples were collected and analyzed for copper, zinc, and molybdenum. These data established local variance and necessary statistical controls. Following this, a total of 151 geochemical samples were used to survey the 3000 square-mile area. Computer contouring of results directed attention to specific target areas for detailed geologic analysis, property acquisition and drilling. A total of 22 copper-zinc and molybdenum anomalies were identified. Four of these were recommended for further exploration. To date, two have been acquired and drilled and preliminary ore reserve and financial analysis have been made on one. The estimated cost and time for the regional exploration phases leading to these targets were thirty man-weeks and $16,000.

Jan 1, 1973

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By Charles A. McLean

Bucketline dredges are machines for excavating large relatively unconsolidated or weakly consolidated materials from below water level. They are at the upper end of the capital cost range and the lower end of the operating cost range for placer mining machines and have digging capacities, typically, of from 100 cubic yards of bank measure material per operating hour for a shallow digging dredge carrying 2 cubic foot buckets to 1500 cubic yards per hour for a large deep digging dredge with 33 cubic foot buckets. Bucketline dredges used in the mining industry have their mineral processing plants mounted aboard the digging hull. Since dredges are high capital cost items, they require large ore reserves, typically at least ten years. Because of their high capital cost they are usually operated around the clock and for as many months of the year as weather conditions will permit. Typically a well run dredge operating year round would be expected to operate for 600 hours per month. Dredges operated in cold climates cannot operate when the weather freezes the dredge pond or the gravels, and dredges operating at sea cannot operate when high waves might batter the digging ladder against the bottom or upset the mineral extraction process.

Jan 1, 1992

By Y. Ye, J. D. Miller, E. Pacquet, S. Gopalakrishnan

From laboratory research activities during the past five years, it is now evident that effective flotation separations can be achieved with the high-capacity air-sparged hydrocyclone. The effectiveness of the equipment has been demonstrated on a pilot-scale basis (1 tph) for a number of mineral commodities including coal, copper, gold, and industrial minerals using a nominal 5-cm x 50-cm system with separation efficiencies equivalent to those achieved by conventional flotation machines. The high specific capacity of the air-sparged hydrocyclone (100 to 600 tpd per cubic foot of cell volume for a nominal 5 cm x 50 cm system compared to 1 to 2 tpd per cubic foot of cell volume for conventional columns and mechanical machines) makes it especially well-suited for the pro- cessing of low-grade ore. As a result of these pilot-scale successes, a number of plant-scale test programs are planned for larger-diameter units to establish wear characteristics and scale-up relationships for design purposes. The status of the air-sparged hydrocyclone technology is reviewed in the present paper, including a description of the system, fundamental considerations of flotation mechanisms, general discussion regarding the effect of control variables, and the significance of feed characteristics.

Jan 1, 1988

By K. F. Unrug

Extrapolation of the rock properties obtained from the cores exploration holes to the surrounding areas often causes problems because of frequent sudden changes in the geologic composition of strata. To address this problem, the author has been developing a method of rapid strength testing "in situ," with application of a borehole penetrometer. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. The results are generated by strength determination on the wall of a drill hole at a site. The newest development is a borehole penetrometer that requires only a 1.38.mm (1.5 in) diameter hole. The small diameter of the penetrometer body allows for drilling test holes with production mine equipment such as roof bolters. It opens the possibility of broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 1999

By Werner Burger, Marcus Lübbers

TBM development in recent decades has been dominated by increased face pressures, larger diameters and multi-mode functionality paving the way to realize projects deemed impossible before. In addition, the trend towards digitalization does not stop at the tunnel portal. A shortage of skilled personnel and the ever-present wish to increase workplace safety, quality and system performance automation, operatorassist or even autonomous systems have become key development targets. The paper will present the current state of the art in light of these special conditions.

Jun 13, 2023

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By John S. Anderson

The need for fuels and minerals in this country is estimated to double, triple, or even quadruple by the end of the present century. Even assuming more recycling of scrap metals and some priority allocation of energy, as has been done, for instance in war time, the projected increase in the nation's population and ever-increasing wants of that population will require vastly more minerals than are now being produced. Since mineral ores are being mined at lower grades, and since all minerals, including fuels, are having to be mined from deeper deposits, the amount of surface land to be disturbed will, inevitably, be increased. We cannot depend on foreign sources to supply all the extra requirements, since the non-U.S. population is increasing, in most cases, faster than our own. Furthermore, starting from a lower base, their mineral needs may accelerate more rapidly than ours. Restrictions on exports may be applied in foreign countries, if it appears that remaining reserves are not sufficient to fill the national needs. In vice; of the opposition which the mineral industry is receiving, as has been well described at these sessions and elsewhere, what can we, as mineral producers, anticipate as regards our ability to continue to operate, to sway nothing of expanding production? Although not minimizing the problems involved, it seems obvious that, except under emergency conditions, the country cannot tolerate a reduction in the available

Jan 1, 1971

By John D. Elmes

The purpose of this paper is to describe the geology and the modelling work carried out to date. The Lisheen Zinc-Lead deposit was discovered in April, 1990. The deposit comprises two stratiform sulphide orebodies, hosted within the Lower Carboniferous Waulsortian limestone formation. The fully diluted geological resource is 22.5 Mt @ 13.02% Zn and 2.19% Pb, based on a total of 548 diamond drill-boles and 10,998 sampled core intersections. Due to the absence of a geological marker it was necessary to apply economic criteria to define and model the resource envelope. In common with other drill-hole geological databases, the establishment of a workable geological model presents unique challenges.

Jan 1, 1998

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By R. D. Irvine

Enhanced concern for protection of the environment and attendant actions by environmental regulatory authorities in support of this concern are influencing to varying degrees the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms. In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States.

Jan 1, 1995