Search Documents

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By G. V. Campbell, O. T. Holdsworth, M. G. Nelson

A senior design project is required by all accredited mining engineering degree programs. Often referred to as the capstone of a student’s education, this project is expected to include all the important components of the preliminary economic assessment of a mineral prospect, including orebody modeling, grade and reserve estimation, selection of mining and processing methods, preliminary mine design, access and utilities, environmental compliance and reclamation, and financial analysis. Two of the authors (Campbell and Holdsworth) completed a senior project in 2021. They analyzed the Akie zinc deposit located in Canada. This paper summarizes the economic analysis portion of that project. The two primary objectives of this economic analysis were risk reduction and integration of economics and engineering. Addressing risk is important as risk is one of the primary concerns in mining investments. Risk reduction was the primary concern through the entirety of this economic analysis. Integration of financial analysis and engineering design was the first component of a risk reduction design. This allowed for financial and engineering design to be optimized in conjunction with one another. This produced benefits from both a financial and an engineering prospective. From a market, economic, and financial risk perspective, risk was reduced by forecasting multiple metal price scenarios, and then addressing the Akie project’s economic viability at each price point. Lastly, risk was address through consideration of nontraditional financing options. The project also sought to minimize financial and human capital risk, by proposing mutually beneficial cooperative social relationships and favorable work, schedules. Description of that work is not included in this paper.

Mar 2, 2022

By Peter W. Lipman

Structural and topographic relief in the Sangre de Cristo Mountains of northern New Mexico provides a remarkable cross section through the recently recognized 23-26 m.y.-old Questa caldera and cogenetic volcanic and plutonic rocks. Although largely eroded, remnants of an ash-flow sheet of silicic-alkalic rhyolite and associated more mafic lavas of the Latir volcanic field are preserved as far as 45 km beyond the source caldera. Within the caldera, the tuff ponded to a thickness of 2-3 km and enclosed chaotic megabreccia fragments which slumped from the caldera walls. At the time of ash-flow eruption, the volcanic field was severely deformed along northwest-trending faults related to the Miocene Rio Grande rift, with most intense deformation occurring within the caldera. Strata were steeply tilted and locally overturned along presumably listric faults. Ash- flow tuffs locally underwent secondary flowage over concurrently developing fault scarps and accumulated within structural basins as rheoignimbritic lava flows. Cogenetic batholithic granitic rocks, exposed over an area of 20 x 35 km, range from mesozonal quartz monzonite to epizonal porphyritic granite and aplite, with the shallower and more silicic phases most abundant within the caldera. Compositionally and texturally distinct granitic phases define a highly evolved resurgent intrusion within the caldera, an incomplete ring dike along its southern margin, and a large mass of less fractionated quartz monzonite south of the caldera. A negative Bouguer gravity anomaly is closely confined to the area of ex- posed granitic rocks; it also reflects boundaries of the Questa caldera. The gravity anomaly is interpreted as defining the extent of the underlying batholith, emplaced into lower parts of the volcanic sequence and underlying Precambrian rocks. Paleomagnetic determinations indicate that the granitic rocks were above Curie temperatures at the time of caldera formation and regional listric faulting, yet most are little different in radiometric age from the intensely deformed volcanic rocks. These relations indicate that the batholithic complex represents the source magma body for the volcanic rocks, into which the Questa caldera collapsed, and was largely liquid at the time of regional tectonic disruption. Compositions of the volcanic and plutonic phases changed from early calc-alkaline metaluminous rocks, to weakly peralkaline silicic rhyolite and equivalent afredsonite-acmite granite at the time of the caldera formation, then back to post- caldera calc-riebeckite granitic rocks. Maximum concentrations of alkalis and minor elements such as Rb, Th, U, Nb, Zr, and Y were reached at the time the caldera formed about 25-26 m.y. ago, but the major molybdenum mineralization of the Questa district took place when the late calc-alkaline granitic ring intrusions were emplaced about 23 m.y. ago, along the south margin of the caldera.

Jan 1, 2013

By Frank P. Frandina, Diane R. Hirsch, David P. Field, Colin R. Weeks

To accommodate growth in air service and to follow the Master Plan for long-term airport development, the Metropolitan Washington Airports Authority established thed2 Development Program at Washington Dulles International Airport. A sub-surface Automated People Mover (APM) System is under construction to replace the Mobile Lounges as the primary people mover system at Dulles. To minimize disruption to airport operations the majority of the APM System’s crossings of Taxi lanes will be undertaken using Tunnel Boring Machines (TBM) or the New Austrian Tunneling Method (NATM). This paper explores the planning and design of these shallow tunnel segments for future generation aircraft loads, within the constraints of minimal construction access under post 9/11 security requirements and the context of the overall airport expansion program.

Jan 1, 2005

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

In this paper, a mixed integer linear programming (MILP) model for the short-term scheduling of open pit mines is formulated. The proposed model aims at sequencing the blocks extraction over multiple short-term periods. The model takes into account multiple processes, waste dumps, and multiple stockpiles. The short-term scheduler makes a decision on the period, destination, and route that ore and waste are supposed to take to minimize costs while meeting all the mining and processing constraints. The destinations of the extracted materials are also controlled by their rock types. A monthly short-term production scheduling case study of an iron ore deposit is carried out over a year to validate the model.

Jan 1, 2011

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

The Yanacocha Project is the first foreign investment in Peruvian mining since Cuajone (1976). Three years after the project began, it has become the largest producer of gold from heap leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits and has attracted the interest of foreign investors in Peru's ample mineral resources. Construction began on August 1, 1992 and after twelve months of arduous work, the first gold bar was poured on August 7, 1993 from ore from the Carachugo mine. In 1993, Minera Yanacocha produced 81,000 ounces of gold and 304,000 ounces in 1994 (40% above budget). Production is expected to exceed 500,000 ounces in 1995 with the start-up of operations in the Maqui Maqui mine. This paper presents a summary of MYSA's experiences during its first two years of operations in the areas of mining, ore processing, environmental protection, loss control and community assistance. The paper also shows that MYSA's successes are not only due to the richness of the deposit, but also to the combination of a number of factors basic to the project's success, such as: an economic policy favoring investment in Peru, the availability of highly qualified local personnel to facilitate the transfer of technology from the United States and the desire and determination of the partners to carry the project forward in an initial atmosphere of uncertainty and terrorism.

Jan 1, 1996

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

By J. R. Evans

Mining claims must have a discovery of a valuable mineral deposit to be valid. When required, a Federal government mineral examiner makes a determination of validity and recommendations thereof to authorized management officials. The examiner should show whether or not an existing mining operation, or a proposed operation have economic viability. This is accomplished through an analysis of legal entities, land status and use, geologic and mineralogic relationships, and mining, milling and processing techniques considered in an appropriate economic evaluation framework. A framework involves market and market entry studies, reserve analyses, all costs analysis, royalty buyouts, tax structure, discount rate of return, and escalation and risk factors. An income approach to value is then used by means of a simple or complex discounted cash flow (DCF) analysis to certify validity. Whether one claim is owned by a single miner, or hundreds of claims are owned by a large corporation, thorough, fair, consistent, and appropriate economic concepts should be applied by the mineral examiner.

Jan 1, 1993

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By William D. Leech

Lebanon used a TBM for the firsttime to excavate a tunnel in the country. A main beam TBM, built in 1979, bored the 3.8 m (12.5-ft) diameter by 4,020 m (2.5-miles) Madiq Tunnel. The TBM bored through karstic terrain of dolomitic limestone, limestone and marly-limestone rock having near horizontal beds with more than twelve faults crossing the axis of the tunnel. The TBM also encountered more than six major karst features, filled with various combinations of boulders, clay, void space and water. The excavation through these collapsed-breccia zones drastically slowed the TBM?s progress. When complete, which the Madiq Tunnel is a part, the Kesrouane Water Project along the coast will bring fresh and irrigation waters to the parched and heavily populated region north of Beirut. The paper will describe the tunnel geologic features, karst genius, TBM upgrades and performance, and TBM/karst difficult situations

By Steve Kral

President Bush’s National Energy Program and his Clear Skies Initiative both emphasize the use of coal to help meet the nation’s growing energy needs. And why not? Coal is currently responsible for more than 50 percent of the nation’s electricity generation. That fact, though, seems to be lost on policy makers, the environmental community and the public. Critics of coal advocate the increased use of renewable energy sources and the increased use of natural gas. Renewables, though, are only capable of generating a tiny fraction of the power required. Natural gas is expensive. And natural gas production cannot keep up with demand, especially given the nation’s increasing energy needs.

Jan 1, 2003

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985