Search Documents

By C. Braux

The aim of this study was to develop an integrated approach to enable identification of areas favourable for the presence of massive sulphide deposits in a given region (Las Herrerias, Spain). It is based on geochemical soil exploration, geophysical surveying (ground gravimetry), detailed geological mapping and a knowledge of the deposits of the South Iberian Massive Sulphide Belt. The multi-dataset approach consists, in the first instance, in standardizing and combining all the geochemical data with reference to their geological setting. Next, the "heavy" anomalies are extracted from the gravimetric survey, regardless of the surrounding context (heavy or light). The results from these two stages are then crossed, so that areas where heavy anomalies are associated with geochemical anomalies can be identified and classified. Crossing the geochemical and geophysical data enables a much tighter selection of anomalies than does the manual superposition of data provided by each method (geology, geophysics, geochemistry).

Jan 1, 1994

By A. C. Lyons

Foreword Sir William Halcrow and Partners are responsible for the design of the Ahmed Hamdi Tunnel as Sub-contractor to the Contractor, Osmac, a joint venture formed by the Arab Contractors, Osman Ahmed Osman and Company of Cairo, and Tarmac International of London. Throughout the paper the term "Client" refers to the Employer, the Ministry of Housing and Reconstruction, which latterly became the Ministry of Development and New Communities of the Arab Republic of Egypt. At the time of writing of this paper only a few hundred metres of the tunnel have been driven, but the design is substantially complete. Introduction The Ahmed Hamdi Tunnel, which is at present under construction, will be a two-lane tunnel crossing beneath the Suez Canal approximately 15 km north of the town of Suez at El Shallufa. It will become the first permanent connection across the Canal since 1967 and is visualised by the Egyptian Government as an early step in the development of the Sinai Desert along the eastern bank. The tunnel will carry pipelines for treated water and electric power cables to assist in this development. The tunnel, which will be 1640 m in length, is being driven through hard clay and mudstone using a tunnel shield fitted with hydraulic excavators. The primary lining is being constructed with precast, bolted reinforced concrete segments with an internal diameter of 10.4 m. The road deck structure and the walls of the air supply ducts beneath it are formed with precast, reinforced concrete units erected immediately behind the shield.

Jan 1, 1979

During the past decade, since the appearance of Popoff's (1966) review of grade tonnage calculations, it has become evident that defining a new method which could be followed step by step by a technician and which would improve reserve estimation was not a simple thing to do. Some concepts have emerged though, and most definitions of ore reserve now require a statement of reliability (USGS, 1975; and Zwarten-dyke, 1976). Exactly how the reliability should be computed is not a straightforward process. It also became apparent that not only was reliability a requirement but that additional questions such as how to predict mining re- serves from geological reserves were to be asked. In fact what became obvious is that specific models have to be designed for each type of mine and for each type of question which is asked. Most methods can be encased within a unique general geostatistical, model, but it takes considerable custom tailoring, and there are still questions that are left unanswered. In this chapter, before giving techniques, we intend to first review what should be required from a grade tonnage calculation done at the exploration stage. If the final objective is still to specify a tonnage and grade, with eventually a reliability, many qualifications have to be made before quoting, and of course, calculating these two numbers. Then the currently avail- able methods will be reviewed and future trends will be shown; finally a few case studies will be given and recommendations about the choice of a model will be made.

Jan 1, 1979

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By T. N. Moore, E. M. De Souza

Because jackleg rock drills are a potential source of hand vibration exposure, they can effectively produce Hand Arm Vibration (HAV) Syndrome in their operators. This will affect operator efficiency and mine productivity. As a result, a significant amount of work has focused on redesigning rock drill handles using new materials to minimize hand-transmitted vibration. In previous work developed by the authors (1991), a detailed study was undertaken to determine the effectiveness of using elastomer covered handles in place of the standard steel design. The results indicated that, for an elastomer-based handle design, the overall acceleration level experienced by the hand can be reduced by as much as a factor of three, relative to the steel handle. It was also shown that this reduction takes place predominantly in the frequency range above 500 Hz. This paper presents an investigation of the long-term effectiveness of an elastomer-cushioned handle under different conditions underground. In this study, sponsored by the Mining Industry Research Organization of Canada (MIROC), a number of cushioned handles were quantitatively and qualitatively tested in five operating mines. The vibration testing program has indicated that the cushioned handle can reduce overall vibration levels by as much as a factor of three. The qualitative assessment program of the cushioned handles by the drill operators has indicated some degree of preference for the cushioned handles over the steel handles, if certain design modifications are performed. This research program indicated that cushioned handles have the potential to become the dominant method with regard to vibration reduction and operator performance.

Jan 1, 1994

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 m (8 ft) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting. Saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can prevent solution flow through large portions of the stockpile. This implies that care must be taken to ensure that ripping is carried out to a depth of at least 2.4 m (8 ft) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2002

By H. Y. Sohn, M. Pérez-Tello, J. Löttiger

An investigation of the oxidation reactions of two industrial copper mattes was performed using dflerential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) at heating rates of 20°C and 8°C/min, respectively. The temperature of incipient reaction, the total exothermic and endothermic heats of reaction and the weight change during the oxidation process were measured as functions of the oxygen concentration in the oxidizing gas, matte grade and matte particle size. The temperatures of incipient reaction measured from the DSC experiments were found to increase monotonically with all three input variables. TGA experiments showed that Cu2O and CuO CuSO4 are formed before the complete oxidation of Cu2S to CuO.

Jan 1, 2000

By P. Anciaux

The EUs? manufacturing and construction industries are vital to Europe?s economy. They rely heavily on a steady supply of materials which meet appropriate quality criteria and are available at a competitive price. The steadily rising global demand for (non-energy) raw materials due to increasing consumption in upcoming economies such as China, India and Brazil, is in some cases leading to rapid price increases, but also supply disruptions which affect the European industry chain. These considerations are at the basis of new policy initiatives that are being prepared by Enterprise and Industry Directorate-General in relation to the competitiveness of the European metals industry. Over the last year the raw materials supply issue has increasingly become the topic of de-bate among various stakeholders. In July 2006 the European Economic and Social Committee adopted an opinion on risks and problems associated with the supply of raw materials to European industry. It is therefore important to identify and analyse the future needs for European industry, the possible constraints and impacts on its competitiveness. The raw materials supply issue should also be looked at from the view-point of the EU extractive industry, which plays an important role in supplying raw materials to the downstream industries and which faces very specific challenges. Within the Enterprise and Industry Directorate-General the different factors that influence the competitiveness of the non-energy extractive industry are being assessed, in order to help identify policies and actions which could contribute to and enhance the competitiveness of the industry.

Jan 1, 2007

By E. W. Davis

This paper deals with the role of the Maintenance Department in a milling operation; specifically, the Mines Development, Inc., processing plant at Edgement, South Dakota. The goal of very maintenance department is the smooth and uninterrupted operation of the plant it serves, To achieve this goal, maintenance men adapt various features and procedures into a program designed to fit the characteristics of their particular plant operation. A few of the basic elements of a sound maintenance program are: 1, A periodic preventive maintenance schedule. 2, A systematic inspection and lubrication procedure. 3. A training program for maintenance personnel. 4 A good equipment-history file system, 5. A carefully planned spare parts inventory.

Jan 1, 1962

An atomic force microscopy (AFM) has been applied to study the adsorption of collectors on mineral surfaces in a copper/molybdenum flotation system. AFM images show that collectors absorb on chalcopyrite surface in patches at pH 11. A study of temperature effect on surface morphology excludes the possibility that these patches are nanobubbles forming on hydrophobized mineral surface. Hydrocarbon oil absorbs on molybdenite quickly, while KEX (potassium ethyl xanthate) has little affinity for molybdenite. Pyrite is much more reactive in water and its surface is easily coated in Ca(OH)2 solutions at pH 11. Based on the obtained AFM images, the adsorption of chemicals on mineral surface and its impact on copper/molybdenum flotation were discussed.

Jan 1, 2012

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By C. A. Moseley, M. B. Kahle

The Gulf Coast Region has been the center of extensive lignite exploration and development activity in the past 10 years. Currently, 27.2 Mt (30 million st) of lignite are mined annually, the majority of which is uncovered by large walking draglines. Projections indicate that production could reach 125 Mt (138 million st) by 1990. As mining moves to deeper depths, removal of overburden becomes the decisive factor in mine planning and cost. The geology of a region plays a key role in the selection of an overburden removal system. While alternate stripping methods must be analyzed to determine the most economical and operationally sound method, so far bucketwheel excavator systems seem to be the best method for removing large volumes of soft, unconsolidated material that is found at projected mining depths in the Gulf Coast region. Geology of Gulf Coast Lignites Extent Distribution of the principal tertiary lignite-bearing deposits in the Gulf Coast Lignite province extend from the Texas-Mexico border to the Alabama-Georgia state line (Fig. 1). The lignite-bearing strata includes portions of eight states: Texas, Louisiana, Arkansas, Missouri, Kentucky, Tennessee, Mississippi, and Alabama. Lignites occur primarily in the Wilcox, Claiborne, and Jackson groups in the Gulf Coast. The uppermost strata of the Midway group in Mississippi and Alabama also contain significant lignite resources. Reserves Commercial lignite seams in the Gulf Coast Lignite province range from 0.6-3 m (2-10 ft) in thickness. The estimated lignite resources throughout the Gulf Coast in seams greater than 0.9 m (3 ft) in thickness and up to 61 m (200 ft) in depth currently are estimated at 32 Gt (35 billion st). Table 1 shows these resources by state. Quality Lignite quality can vary within individual mining areas and seams. However, trends in quality occur because of the depositional environment, age, and west-to-east geographical location. Better quality lignites occur in the Wilcox group in Texas and Louisiana. Poorer quality lignites occur in the northern regions of the Wilcox group and those of the geologically younger Claiborne and Jackson groups. Environmental Conditions Gulf Coast province environmental conditions are ideal for successful mine reclamation. The lignite occurs in flat to moderately rolling terrain, a topography easily reproduced from the spoil dumps or spoil rows developed during the mining operation. High to moderate rainfall facilitates rapid revegetation. Evidence from current mine reclamation programs and ongoing test plot studies indicate that mined lands can be reclaimed to reach premining productivities. Sometimes productivities are even greater than that of premining conditions. Existing Mining Methods Present Mines & Production There are seven active mines in the Gulf Coast province, all located in Texas (Fig. 2). Lignite

Jan 8, 1983

By J. M. Hans, M. F. O’Connell, G. E. Eadie

INTRODUCTION The U.S. Environmental Protection Agency (EPA) was required, under Section 114(c) of Public Law 95-604, to provide a report to Congress identifying the location, and potential health, safety and environmental hazards of uranium mine wastes together with recommendations, if any, for a program to eliminate the hazards. The approach taken to prepare the report was to develop model active and inactive mines and locate them in a typical mining area to estimate their environmental impact. A list of uranium mines was acquired from the U.S. Department of Energy (DOE). The inactive mines were separated from the list and sorted into surface and underground categories. A literature search was conducted to obtain and consolidate available information concerning the environmental aspects of uranium mining and shortterm field surveys and studies were conducted to augment this information base. Radioactivity emission rates were measured or estimated for each mining category and were entered into computor codes to assess population exposures and subsequent health risks. The general environmental condition of inactive uranium mines was determined by walk-through surveys in several mining areas. INACTIVE SURFACE MINES We assumed that a model inactive surface mine contains a single pit with the wastes (overburden and sub-ore) stacked into a pile adjacent to the pit area. No credit for reclamation is given to the model mine. In lieu of the availability of individual mine production statistics, the model surface mine size was established from the total ore and waste production statistics for all surface mines, divided by the number of inactive surface mines. The number of inactive mines, obtained from the DOE mine listing, are summarized by type and location (Table 1). For modeling, we assumed that there are 1,250 inactive surface mines. The total or cumulative waste and ore production for inactive surface mines from 1950 to 1978 is not fully documented. Uranium mine waste and ore production statistics, on an annual basis, were available for both surface and underground producers from 1959 to 1976 (D0159-76). Annual uranium ore production for each uranium mining type are available for 1948 to 1959 (DOE79) and for combined ore production TABLE 1. Consolidated list of inactive uranium producers by State and type of mining [State Surface Underground AL 0 9 AZ 135 189 CA 13 10 CO 263 902 ID 2 4 MT 9 9 NV 9 12 NJ 0 1 NM 34 142 ND 13 0 OK 3 0 OR 2 1 SD 111 30 TX 38 0 UT 378 698 WA 13 0 WY 223 32 Total 1246 201T] for underground and surface mining from 1932 to 1942 (DO132-42). In order to estimate waste accumulated prior to 1959, the waste-to-ore ratios from the 1959 to 1976 period were plotted vs. time and line-fitted by regression analysis (Figure 1). Unfortunately, the extrapolation of the line to years prior 1959 approached zero in 1954 although surface mining began in 1950. Therefore, a waste-to-ore ratio of 8:1 was used for the period of 1950 to 1959 based on ratios estimated by Clark (C174). The waste to-ore ratios for 1976 to 1978 were estimated using the line established in Figure 1. By using waste-to-ore ratios and ore production data, the cumulative waste and ore production for both surface and underground uranium mining is estimated to 1978 (Table 2). The estimated cumulative waste from uranium surface mining for 1950 to 1978 is 1.73 x 109 MT. A crude estimate of the waste accumulated at the model inactive surface mine can be made by dividing the total waste produced to 1978 by the number of inactive mines. This, however, overestimates the waste tonnage because some of the contemporary wastes are being produced by active mines, and the waste accumulated at newer mines has increased in recent years. To adjust for this overestimate, we assumed that all mines operating in 1970 will be inactive by 1978. This eight year period is approximately one-half the lifetime of a model

Jan 1, 1981

Roof bolting has been widely used in hard rock underground mines for its many advantages. In this paper, the applicability of roof bolts to mine openings in frozen ground and effects of bolts on the stability of the openings are presented. A comprehensive finite element program ABAQUS, was used to analyze the temperature distribution, the stress field, and the displacement field around a mine opening. Openings supported by roof bolts and unsupported were analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration with a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts are less than five, the displacement within the ground can be improved only locally.

Jan 1, 1995

By Qing Wang

A longterm overburden removal plan can be realistic and optimum only when the cost and capacity profiles off the equipment assigned to the operation are taken into consideration. Therefore, the planning should involve the proper assignment of equipment capacity by insuring a timely investment and a timely replacement policy throughout the mine life. A dynamic solution algorithm has been developed, by which all possible truck fleet alternatives are evaluated for each year off the operation. Cumulative cost off the operation is carried throughout the analysis. The optimum solution is obtained by selecting the minimum cumulative cost at the last year and tracing backward the best fleet alternative for each year. The solution provides: 1. the optimum amount of overburden to be removed each year; 2. the best fleet to be assigned to the job; and 3. the best equipment replacement policy.

Jan 1, 1989

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By Tanya J. Gallegos, Mojisola A. KunleDare, James V. Jones III, Charlotte E. Riggs

The United States Geological Survey (USGS) provides scientific information for the Department of Interior and the nation, consistent with its original mission expressed in the Organic Act of 1879 (43 U.S.C. 31): “the classification of the public lands and examination of the geological structure, mineral resources, and products within and outside the national domain.” Legislation such as the Energy Act of 2020 and the 2022 Infrastructure Investment and Jobs Act (43 USC 31l) and recent executive actions (Executive Orders 14154 , 14153, 14241 Secretary’s Orders 3417, 3418, 3422, 3436) underscore the importance of mineral resources and focus USGS activities on mapping and assessing mineral resources, with a particular focus on those presently identified as critical, both in ground and above ground in mine wastes. This article reviews selected activities and accomplishments by the USGS Mineral Resources Program related to critical minerals in 2025. Highlights include a new List of Critical Minerals, a first-ever national mine waste inventory, international minerals partnerships, mineral resource assessment advancements, and national data collection activities and outcomes of the Earth Mapping Resources Initiative (Earth MRI). The selected contributions are not comprehensive but are intended to demonstrate USGS leadership in critical mineral mapping and assessment, the importance of domestic and global partnerships, and the breadth of research activities that are responsive to national needs and priorities.

May 1, 2026

By J. Ugarte-Núñez

Biodiversity assessments that are developed in different stages of a mining project, have different objectives that define the methodology to be used in each of these stages. In this way, we define two stages of a project: 1) the time at which assesses the state of biodiversity or biological components, before any intervention in the project area, previously defining the area of direct influence and indirect influence of the project for each biological group to be evaluated and 2) the time when certain groups or biological, are monitored during the developmental stages of the project with you to obtain information about the level impact they may have, for project activities. It discusses the methodological differences that must be used in both biodiversity assessments: to develop biological baselines and in those assessments aimed at monitoring different components of biodiversity.

Jan 1, 2011

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By L. E. Bowman

Efficient filtration of fine kaolin particles plays a crucial role in processing of raw kaolin to a marketable product. Oftentimes, filtration Is the rate controlling step of the whole process. As a consequence, plant production is dependent, to a great extent, on the rates being achieved In filtration. In order to alleviate the bottleneck in production, Nalco Chemical Company initiated a reagent development program to chemically enhance the performance of the filtration units. Filler aids of different classes were synthesized for evaluation. These include reagents whose primary mode of functionality were: coagulation, flocculation, thickening, and combinations of the preceding. All reagents that were synthesized and tested were listed under the appropriate Food and Drug Administration sections of the Code of Federal Regulations. This paper discusses the development and application of a new reagent that Improves the filter production rate with minimal Impact on filter solids. The results of laboratory filter studies along with plant data are presented and discussed. Plant data indicate that this reagent is capable of increasing production rates by as much as 35% on various clays of coarse particles to the finest fractions, as well as clays that are calcined. The reagent&apos;s Impact on solids content, re-slurrying characteristics, Brookfield and Hercules viscosity, and drying is within the standards set by plants who have evaluated and now use this product.

Jan 1, 1993