Search Documents

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By James Matlock

The announcement of a minable reserve of 13.6 Mt (16 million tons) averaging 0.9 g/t (0.027 oz per ton) Au and 2.4 g/t (0.71 oz per ton) Ag for the open pit-heap leach reserve at Red Mountain No. 3 in Ouray County, Colorado, by Cornucopia Resources in November 1985 brings another open pit-heap leach precious metal ore body to the production stage. With about 8.2 Mt (9 million tons) of waste and metallurgical studies showing acceptable recovery rates, low reagent consumption, and good final percentage recovery, Red Mountain is a discovery that will add to the precious metal inventory of the US. Frank Baumgaruler of Denver, CO, recognized the precious metal potential in Red Mountain No. 3 and acquired all of the old claims. James Matlock conducted a field reconnaissance over Red Mountain No. 3 independently of the Baumgartner activities and recognized epithermal alteration and mineralization in the Tertiary volcanics. He recommended acquisition of the ground and was able to obtain rights and drill six core holes for Amoco in 1982. Amoco drilled a further nine core holes in 1983, but then dropped the property. Cyrano Resources examined the data and through its consulting geologist, V.F. Hollister, acquired the rights dropped by Amoco. In 1984 Cyrano began further drilling of the ore zone demonstrated by Amoco but they were then acquired by Cornucopia Resources. Cornucopia completed development of the property and commenced the permitting process in 1986. The property was recognized as a disseminated gold deposit by both Baumgartner and Matlock, and both deserve credit for properly evaluating mineralized outcrop in the Tertiary volcanics. However, Cornucopia recognized the profit potential in the heap leach exploitation of the ores and de- serves credit for completion of premine feasibility studies. The discovery is clearly a geological one, but the premine engineering studies were essential to the conversion of the prospect to a commercial mining enterprise. The deposit lies on the circular bounding fault of the Silverton caldera. Two reprints follow that help understand the geologic setting of the ore controls.

Jan 1, 1990

By G. A. Kordosky

The control of pH in solvent extraction circuits is an old technique (1,2) but one which has a large potential for future use. The equilibrium position of any reaction which has hydrogen or hydroxide ions, either as products or as reactants, can be controlled by pH adjustment. Several examples of reaction types which are important in solvent extraction systems and which also show a pH dependence are shown in Figure 1. The examples were chosen to show the wide variety of reactions which fit the above criteria, but it is not meant to be a complete listing of all the possible reaction types, Some of the reactions are presented in a simplified form. It is the intent of this paper to discuss pH controlled solvent extraction reactions for some relatively simple systems through more complex ones.

Jan 1, 1979

By Stefan Zanon, Ty Faechner, Clayton V. Deutsch

Secondary data are important in geostatistical simulation of continuous variables. Geophysical data and geological trends are used for modeling porosity and permeability. Multiple mineral grades must often be modeled for mining applications. Sequential Gaussian simulation (SGS) is often used because of its relative simplicity and robustness. The two most common approaches to integrate secondary data in Gaussian simulation are with (1) locally varying mean, or (2) collocated cokriging. A significant problem with both of these techniques is variance inflation, that is, the variance of the resulting simulated values is too high because of an inappropriate decision of stationarity or an artifact of choosing a single secondary data in presence of many. We introduce a self-healing procedure for dynamic correction of this problem. The dynamic correction is different for the locally varying mean approach and for collocated cokriging since there are different reasons why each of these methods causes variance inflation. The reasons for variance inflation are discussed and the self-healing is applied to a number of data sets.

Jan 1, 2002

By Frank W. Bowdish

Studies of sulfidization and flotation of chrysocolla involving the use of pH and sulfide ion instruments, a Zeta meter, microflotation techniques, and sensitive determinations of adsorbed sulfur have given new insight into the mechanism of the process. Factors that affect the recovery of sulfidized chrysocolla by flotation appear to be the pH at which it is sulfidized, and certain alterations of the surface that occur during aging after sulfidization. Such aging results in increased recoveries. The surface charge, as measured by electrophoretic mobility, of chrysocolla shows an unexpected negative increase as pH values are changed from 6.0 to about 4.5, and this appears to be correlated with increasing sulfur adsorption and flotation recovery over the same or even wider pH ranges.

Jan 1, 1970

By Deepak Malhotra, Linda Battich

INTRODUCTION Mineral processing plants generally operate efficiently within the technical, economic and management constraints applied to them. They have no choice, because the dynamic and competitive nature of the mineral business dictates that survival and/or prosperity of the company depends on being a low cost producer. Progressive mineral companies realize that market downturns will occur, and they must continuously strive for lower unit production costs rather than be satisfied with the status quo. Mineral companies generally tend to reduce costs during market downturns. This short-term solution is achieved by high grading of ores, and cut-backs In waste stripping, exploration, and capital expenditures.(1) However, to remain a low-cost producer in the long term, companies must enhance revenue and reduce cost simultaneously. This Involves continuous evaluation of technologies and reagents, periodic audits to locate revenue losses; and gathering and analyzing statistical plant data to clearly understand the Impact of process variables on efficiency. Mineral companies are caught in a Catch-22. They need resources to accomplish the objectives outlined above. Most mill stuffs have been cut to the minimum level necessary to maintain production. Resources such as time, manpower and money are scarce, and mill metallurglsts struggle to use these resources productively. Is your flotation plant optimized? History Indicates that successful operations constantly tune the flotation circuits to Improve metallurgy or reduce cost. This Is the essence of evolutionary change In mineral processing operations. A plant auditing approach can play a key role in assisting the process engineers to achieve the overall objective of enhancing metallurgy and reducing cost with limited resources through evolutionary improvements. FLOTATION SYSTEM The flotation process is the most widely wed concentration process In the world today. The number of variables that can affect the flotation results Is very large, maybe over 100. These variables can be divided Into three main groups: (2) (1) ore and mineral properties; (2) reagent treatment; and (3) flotation machine characteristics. Some of these variables can be controlled while others have to be accepted. Recently, Investigators (3,4) have attempted to describe the flotation process as an engineering system which includes chemistry, equipment and operating variables. Though some of the variables are Independent, most are co-dependent. thus making it difficult to develop simple cause and effect relationships. For example, it is easy to understand the effect of reagent change on recovery and grade In the rougher circuit, but very difficult to quantify Its impact on filtration downstream. Plant audits on a periodic basis are necessary to develop an understanding of the Interactive nature of the system. Auditing provides comparisons of plant operating performance before and after variable changes. OVERVIEW OF PLANT AUDITING An audit Is a formal, thorough and periodic examination of a system. There are various types of audits (i.e., geological, environmental, metallurgical. economic, etc.), and each serves a different purpose. (5) The discussion here is related to plant and/or metallurgical audits. Neale and Flintoff note that two key factors governing changes In an operation are: (1) the opportunity must be recognized; and (2) the justification for change must exist. (6) Both factors emphasize the critical role of successful plant auditing. Without plant audits. many opportunities for improvement must go unrecognized. On the other hand, when a situation ripe for improvement Is recognized. the hard data from a plant audit can reveal the expected impact of an operating change.

Jan 1, 1993

By R. Bleischwitz, R. Delzeit

"Tantalum, a heavy metal with characteristics such as superconductivity and high terminal resistance, nowadays is the most efficient material for production of capacitors, which are essential for production of small electronic applications like notebooks and cell-phones. It is one of the strategic resources for information societies. With supply extracted from Central Africa (Congo / DRC), China, Australia, and Canada, it can serve as an example for sustainability efforts in the management of non-renewable resources in Developing Countries, Newly Industrializing Countries and Industrialized Countries alike. The paper analyzes the life cycle of tantalum in its environmental, social, and economic dimensions. The first section highlights the importance of tantalum, showing a demand-driven market. The second section analyzes current and future supply. The third section tackles environmental and social impacts of tantalum mining in different legislations. The fourth section especially deals with the Case of the Democratic Republic of Congo since companies have been accused of participating in a civil ‘resource war’. Section five will draw conclusions for sustainable resource management. Written in an interdisciplinary manner, the article has a bearing on economics, especially on resource economics and new institutional economics, as well as on geography. It deals with questions such as security implications of physical scarcity in rapidly growing markets. In doing so it can, firstly, be shown that information exchange in combination with reputational risks lead to a shift in extraction activities from a Developing Country (DRC) to an Industrialized Country (Australia); i.e. a ‘race to the bottom’ does not take place. This, however, does not mean that market mechanisms work properly since information exchange (especially with China) is incomplete, moral hazard still prevails, and inadequate institutions hamper development processes in an exporting country like Congo. Any sustainable resource management for tantalum not only should foster gathering and exchanging better information on environmental and social impacts, but also incentives for upstream metal recycling in industry as well as support for governance processes in Developing Countries"

Jan 1, 2005

By George Munro

Heavy water inflows of up to 1350 1/sec in the 19.6 km Moawhango-Tongariro Tunnel section of the Tongariro Power Development Scheme in New Zealand gave rise to severe operating problems, particularly in the equipment stripping stage when pumping installations had to be removed. Due to the necessity to commence stripping from the upstream side the contractors. Codelfa-Cogefar (NZ) Limited, took the decision to install a steel bulkhead some 5000m in from the lower. Tongariro, portal. The article lists the considerations taken in the placement of the bulkhead, and gives details of its design, installation and final removal. A brief description of the geology of the tunnel. together with water flow sources, rates and pressures is also included.

Jan 1, 1981

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By Dick Lewis

The Misima deposit is on Misima Island in the Lousaide Archipelago, 240 km east-southeast of the Papua New Guinea mainland, and 600 km east of Port Morseby. Misima is a narrow mountainous island 40 km long and up to 10 km wide. The highest point is 1035 m above sea level. Gold mineralization is restricted to the eastern and less rugged third of the island. The Melanesian population lives in coastal villages. Subsistence agriculture is the main activity, although copra and cocoa are grown in plantations on the eastern and southern coasts. Prior to 1950, mining was important in the economy of the island. Climate is tropical, with little seasonal variation in temperature or rainfall. Tropical cyclones occur about every 10 years (Fig. 1).

Jan 1, 1990

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By Chinmoy Sarkar

Mining organizations have been trying to employ best practices at exploration, exploitation and processing level to increase productivity in the supply chain. Traditional techniques of cost control can no longer meet the ambitious target of mine managers. An integrated perspective of Mining Value Chain with enterprise-wide application of information technology (IT) ensures the ability of every mining processes to improve energy, land, capital and labour resource performance while continuing to cut costs and achieve profitability. IT offers enormous potential in mining industry at shaping entirely new opportunities to create value. This paper characterizes important entities of Mining Value Chain and attempts to provide a vision on how IT can transform the mindsets of industry managers addressing the needs of the customers.

Jan 1, 2002

By George J. Simchuk

The selection of a stripping method and subsequently, the stripping equipment, are two of the most important decisions confronting a project engineering staff during the initial feasibility study of a new coal stripping operation. The selected stripping units average from 60 to 70 percent of the total capital outlay for mine equipment and their selection will affect the type, size, and quantity of the attendant equipment, such as loading shovels, drills, haulage trucks, and bulldozers. This paper is intended to report on an in depth study by Utah's Technical Services Staff regarding the selection of stripping equipment for the Goonyella Coal Mine in Queensland, Australia. We will touch briefly, on the objectives considered in this selection; the various alternatives which were explored; the general assumptions that were followed throughout the engineering and design of an appropriate stripping system; and computations necessary to determine the amount and size of stripping equipment. INITIAL EXPLORATION Utah Development Company (presently 90% owned by Utah Construction & Mining Co. and 10% by Australian investors) commenced systematic geological studies of the Bowen Basin coal fields of Central Queensland in 1961. The Blackwater Mine as shown in Figure 1 has since been established in this area and is now producing 3.0 million tons per annum of washed coking coal. Geological reconnaissance was then extended to the northern part of the Bowen Basin and in 1963 Utah's coal prospecting area covered 2444 square miles of Central Queensland. The authority to prospect north of Blackwater has since been trimmed to 810 square miles by relinquishments to the State.

Jan 1, 1971

By Taira Emoto, Hikozou Imaoka, Sohta Takatsu, Takeshi Suzuki, Yoshihito Minami

An Oval Section TBM (tunnel boring machine) enables excavation of tunnel with elliptical cross section by inclining the cutterhead. It is developed to utilize the proven conventional TBM technology with minimum modifications. Various types of tunnels which are preferred to have non-circular cross section can be economically excavated, reducing both overbreak and the amount of muck produced. On the other hand, an inclined cutterhead may create a number of new problems, such as in excavation efficiency and steering that are unknown in excavation works using a circular TBM. This paper reports on verification tests carried out to examine the extent of such problems using experimental models of the machine in an attempt to confirm the feasibility of the Oval Section TBM.

Jan 1, 1997

By Hélio Blak

The Paranapanema Group was created in February 1996 when a group formed by the Brazilian pension funds acquired four companies dealing with nonferrous metals. The new Paranapanema Group, basically related to the tin and construction business, became the sole Brazilian primary copper producer, the second zinc producer and one of the most important producers of copper products, mainly tubes and fittings. To put together such different companies, managed before by family groups and with different cultures and principles, was and still is a big challenge. The strategy of developing and consolidating it as an homogeneous group is based in three pillars: an increase in production, quality and technological improvements on products and market mix and a permanent cost reduction program, using all the potential synergies founded.

Jan 1, 1998

By Craig J. Nelsen, David A. Smith

In 1987, LAC Minerals (USA), Inc. conducted a high resolution helicopter electromagnetic (EM) and magnetic geophysical survey on the Ortiz Mine Grant, New Mexico. The primary purpose of this survey was to assist in geologic mapping of a major structural zone, the Tijeras-Canoncito Fault System (TCFS). This structure is a very important ore- controlling feature in the area. Geophysical signatures over known deposits was a secondary goal of the survey, but direct detection of mineralization was not anticipated. The TCFS was revealed to be a complex, branching and anastomosing system of faults which locally form the bounding structures of a graben. The geophysical survey guided subsequent geologic mapping by redirecting field investigations, and geophysically redefining some features which previously had been only partly defined.

Jan 1, 1989

By Marcel Michaud

Over the past five years, the two-fold growth in Canada's coal industry "Figure, 1" results primarily from the coking coal market to Japan and, to a lesser degree, by the increasing use of sub-bituminous and lignite coal for power generation in the Prairie Provinces. This expansion will continue, but production of coal for domestic thermal generation of electricity will grow at a faster rate than coking coal exports "Figure, 2". Half of the 20 million tons of thermal coal used for electrical power generation in Canada during 1974 were imported by Ontario Hydro from U.S. coal companies in West Virginia and Pennsylvania. Ontario Hydro's Nanticoke station on Lake Erie which will consume 7.5 million tons of coal in 1977 when fully operative, as well as other future planned projects, could cause Ontario Hydro's coal consumption to rise from 10 million tons today to 20 to 25 million tons by 1985

Jan 1, 1975

By P .. F. Ziemkiewicz, T. E. Rymer, J. J. Renton

Prediction and quantification of acid mine drainage (AMD) from a given rock unit is in its infancy. Acid Base Accounting is the current procedure. II is a useful screening procedure and is designed to indicate whether a rock unit will or will not produce acid. In this sense, Acid Base Accounting is qualiwtivc. Researchers at West Virginia University arc developing a prediction method to estimate how much acid will be produced over the life of a rock unit's AMD production. TI1c AMD prediction procedure can also evaluate the required rates and effectiveness of various AMD control amendments. This presentation discusses the WVU AMD prediction procedure in the context of historical approaches and indicates the mechanics and applications of this new technology.

Jan 1, 1991

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002