Search Documents

By A. D. Davis, G. A. Zabolotney

A ground-water flow model was developed to simulate the postmining recharge rate from precipitation at the Belle Ayr surface coal mine, which is located in the Powder River Basin near Gillette, WY Wyoming state regulations require that reclaimed lands should provide a rate of recharge that approximates the premining rate. Steady-state calibration and transient simulations showed that the postmining recharge rate through spoil is at least 50 mm (2 in.) per year, exceeding the original infiltration rate of 4 mm (0.16 in.) per year to shallow overburden aquifers. Major reasons for the increase include the flat topography of the reclaimed areas and the decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate that is less than 50 mm (2 in.) per year but still somewhat greater than the premining rate.

Jan 1, 1997

By John C. Stam

During the past 20 years, the seismic refraction method has been used for depth to bedrock investigations. Its usefulness, however, has been recognized mainly in engineering applications, for instance in connection with the construction of power stations and in dam site investigations etc. Although some knowledge of the depth to bedrock can be of advantage in many other fields, the use of the conventional 12 or 24 channel seismic refraction equipment has been very limited, especially in ore prospecting and mining operations. The reasons for this are mainly the rather complicated operation of the instruments and the high costs. A conventional seismic equipment requires a crew of six men, a highly trained operator and an interpreter. Furthermore, the use of explosives can under certain conditions be undesirable (naighbourhood of houses, damage to agricultural areas etc.). Since 1957 a new one-channel seismograph, 'constructed by Geophysical Specialties Company, Minneapolis, Minnesota, has been in use and this instrument simplifies operations and reduces their costs considerably.

Jan 1, 1959

By LeEtta M. Shaffner, John R. Marks

INTRODUCTION In the last twelve years, underground stoping methods at the Homestake Gold Mine have evolved from open cut-and-fill with jacklegs, cribbed raises and electric slushers to ramp-based mechanized cut-and-fill (MCF) and vertical crater retreat (VCR) with dieselpowered loaders, trucks and drill jumbos. The evolution was swift. Unfortunately, ventilation practices have had trouble keeping pace. Stope ventilation is still too dependent on auxiliary fans and coolers. A single large MCF stope might contain up to eight headings, each of which requires significant ventilation resources when a diesel loader is present. Air is shortcircuited all too frequently through mined-out VCR panels. These factors and the recent rapid decent of the center of mining prompted a study to improve ventilation practices and to more accurately project future requirements. BACKGROUND In 1992, the underground portion of the Homestake Gold Mine produced 8336 kg of gold from 1407 ktons of ore (268,000 oz from 1,551,000 st). The ore is hosted in low to medium grade meta-sediments. Stoping took place from 420 to 2347 m below the surface (1400 to 7700-ft levels). The weighted center of mining was 1662 m deep (5450-ft level) in 1990 and is projected to be 1890 m (6200-ft) in 1993. The deepest level is 2440 m (8000-ft) where the virgin rock temperature (VRT) is 56.1°C (133F). The mine is ventilated by 504 m3/s (1,069,000 cfm) measured at mid-exhaust-circuit density. The air-conditioning system includes an 8.1 MWR (2300 ton) controlled recirculation plant, a 2.0 MWR (580 ton) chilled water plant, a 1.0 MWR (290 ton) exploration drift refrigeration plant, 28 spot-coolers totaling 3.4 MWR (960 tons) and 35 spray coolers totaling 1.5 MWR (420 tons). The mine employs 117 diesel units with a total nameplate rating of 7961 kW (10,672 hp). These units include twenty-four 1.5m3 (2-yd) loaders, twenty-six 2.7m3 (3.5-yd) loaders, fourteen 3.8m3 (5-yd) and two 7.6m3 (10-yd) trucks, and assorted utility vehicles and drill jumbos. THE STUDY In April 1991, the University of Nevada-Reno (Mackay School of Mines) and the South Dakota School of Mines and Technology cooperated with Homestake on an MCF study. Mackay instrumented a stope with thermocouples, air velocity meters and hygrometers (Duckworth, 1992). South Dakota Tech conducted a finite-elements computer analysis of a back-filled MCF stope with/without light-weight shotcrete insulation on the sidewalls and back (Chellam, 1992). Homestake conducted an empirical analysis of deep-level MCF stoping. This paper describes the Homestake study. Twenty-three of the forty MCF stopes deeper than 1800 m were surveyed at least once during the last quarter of 1992. The stopes not included were being cable-bolted or back-filled. Figure 1 shows the complexity of one of the ramp-based stoping areas included in the survey. This particular stope has six separate production headings. A baseline wallrock heat load was derived for each stope or heading from psychrometric calculations. Broken ore, waste rock fill and fissure water were noted when present and the effects included in the baseline heat load. Other heat sources often mentioned in the literature such as metabolic heat from workers, heat from explosives and small electric loads were neglected. Fan heat was considered part of the ramp & crosscut heat load and thus not included in the study. Diesel heat was addressed separately. RESULTS Survey results, plotted as the heat flux against VRT, are shown in Figure 2. The equation for the regression line is: W/m2 = 2.1236*VRT - 75.405 The 0.31 correlation coefficient is poor which implies that the results should be used cautiously. Previous experience strongly suggests that differences in productivity are most likely responsible for the scatter in data points. A rapidly advancing stope will have a

Jan 1, 1993

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By A. L. Stomberg

Federal and State surface coal mining regulations require special handling of prime soil materials which result in additional costs, and no actual benefit when prime and non-prime soils are similar. The Coteau Properties Company proposes to mix both prime and non-prime topsoil and subsoils at the Freedom Mine in Mercer County, North Dakota, based on an analysis of soil physical and chemical characteristics which show these materials to be comparable.

Jan 1, 1985

By M. Schultz

The cost of remediation often drives the selection of the preferred remedial alternative at hazardous waste sites. The use of probabilistic cost/risk analyses can aid in predicting costs of remedial alternatives. Three types of information are discussed in performing cost/risk analyses: (1) data on the quantity of contamination versus the contaminant concentration; (2) unit costs of remediation for the remedial alternatives; and (3) risk to contaminant concentration relationships. Cost/risk evaluations are performed on a site-by-site basis, to account for combined risks of different contaminants and differences in quantity to be remediated versus contaminant concentration. The cost/risk analysis produces a graph of risk versus cost for each of the remedial alternatives. These costs are then compared to facilitate selection of a preferred alternative. An example of comparison of alternatives is illustrated for a historic coal gasification site.

Jan 1, 1992

By Frits Agterberg

Statistical exploration uses statistical methods to identify targets for more detailed investigation by estimating the odds of occurrence of mineral deposits. The study area which contains the possible targets may be as large as 1 000 000 km2 or as small as 100 km2. Results are presented in terms of a probability index for the existence of a deposit or, more precisely, in terms of expected dollar value for a unit area, or even in terms of number, size, and grade of deposits remaining to be discovered. Typically, selected geological, geophysical, or geochemical information is systematically quantified and statistically analyzed by using the computer in order to distinguish between geological environments on the basis of the probability that they contain undiscovered deposits of a specific type. All possible targets are compared with one another by using information on areas known to contain deposits. The information on the known areas is either a set of control data consisting of values for the same parameters as are quantified for the entire study area, or it embodies a specific model for the occurrence of a given deposit type. Examples of both procedures will be discussed in this chapter.

Jan 1, 1979

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By R. A. Halatchev

Historically two basic approaches of production sequencing have been formed in the theory of open pit mine design. The first approach implements a technological discretization of the pit space within the ultimate pit outlines where the minimum working width is the limiting technological factor. The second approach uses a pseudo-economic discretization based on the implementation of analytical methods for designing intermediate/ultimate pit outlines and the concept of pit shells generation. The paper offers an elaborate analysis of both approaches used currently for discretization of the geological medium into working benches and modelling the working zone of open pit mine. The analysis is extended with a new vision for unification of the mining systems in open pit mine design under the form of a classification. A comparison of the approaches is provided to illustrate their advantages and disadvantages with regard to the implementation of the principle of waste deferment as one of the main principles of mine planning that exploits the time effect of money.

Jan 1, 2003

By D. E. Munson, T. M. Torres, D. A. Blankenship

The Thermal/Structural Interactions (TSI) In Situ Tests are a series of large scale, well instrumented tests that have been constructed at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. As a precursor to the TSI tests, a ventilation drift (Room D) was mined, drilled and instrumented. This room provided the contractor an excellent area to practice controlled construction methods and was a proving ground for construction monitoring and documentation methods. All gages in this first room have been monitored since their initial installation, which has provided a small, but representative, data base. These data also were the first to be available from any TSI area for analysis. This paper discusses the construction activities in Room D and the data generated from the construction and drilling. Deformation of the room is compared briefly to numerical calculations that used a rather simple creep model as a reference. The constitutive model for salt, it appears, must be improved before it can predict the underground deformations.

Jan 1, 1986

By Keith G. Wallace, Justus B. Deen, Daniel J. Brunner

This paper describes the impact of natural ventilation pressure (NVP) on the Nuclear Waste Isolation Pilot Plant in New Mexico (WIPP). The WIPP site is a U.S. Department of Energy underground facility for the disposal of low level radioactive transuranic defense generated waste. Because the facility is designed for the storage of nuclear waste, special design considerations are necessary to ensure containment of potential radioactive releases. The main design considerations which influence the ventilation system are the requirements of separate air splits for mining and storage operations and of air filtering before atmospheric discharge in the event of a radioactive release. The leakage between the two air splits must always be from the mining area to the storage area. The transient effects of natural ventilation pressures, caused by seasonal and diurnal surface temperature changes, impact the ventilation characteristics throughout the facility. This paper discusses the measurements taken to quantify the changes in NVP and the engineered systems designed to mitigate against the effects of NVP.

Jan 1, 1991

By A. K. Haines, M. W. Godfrey, D. M. Miller, P. C. van Aswegen

The Bacterial Oxidation [(BIOX)] process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairvew Mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developmenst to improve plant operating efficiencies. These new developments, which include a higher solids content of the pulp feed to [BIOX], lower retention times, higher operating temperatures, lower power utilizaton for oxygen dispersion and reduced nutrient addition, have all been successfully implemented on the Fairvew plant. It has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Contineous cyanidation pilot plant work conducted on [BIOX] product has indicated that cyanide consumption can be drastically decreased if a continuons flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1992

By Osvaldo A. Bascur

The implementation of continuous quality improvement is the confluence of Total Quality Management, People Empowerment, Performance Indicators and Information Engineering. The supporting information technologies allow a mineral processor to narrow the gap between management business objectives and the process control level. One of the most important contributors is the user friendliness and flexibility of the personal computer in a client/server environment. This synergistic combination when used for real time performance monitoring translates into production cost savings, improved communications and enhanced decision support. Other savings come from reduced time to collect data and perform tedious calculations, act quickly with fresh new data, generate and validate data to be used by others. This paper presents an integrated view of plant management. The selection of the proper tools for continuous quality improvement are described. The process of selecting critical performance monitoring indices for improved plant performance are discussed. The importance of a well balanced technological improvement, personnel empowerment, total quality management and organizational assets are stressed.

Jan 1, 1995

By Jean-François Boucher, Ernest K. Yanful, Mei Lin Shelp, Lionel J. J. Catalan

Shallow water covers for preventing acid production in tailings are based on the principle of minimizing oxygen availability. Resuspension of material from the tailings bed may result in increased oxidation and metal releases since dissolved oxygen is at near saturation levels in the water cover. Resuspension can be caused by waves and currents strong enough to mobilize the surface of the tailings bed. Tailings resuspension was measured with sediment traps in the Upper Cell of the Heath Steele site near Mirarnichi, New Brunswick Canada. Although significant amounts of resuspended tailings were collected in all traps, analysis of resuspended solids and bed tailings suggests that for the observed wind conditions resuspension did not occur at locations where the water cover depth was greater or equal to 1.0 m. Currents were likely responsible for the transport of resuspended tailings from shallower areas to locations where the water cover was deeper than 1.0 m.

Jan 1, 2000

By Gordon S. Thomas

The problem of how best to exploit a reserve has vexed mine planners and design engineers since mining began. The cyclic nature of the mine design-scheduling problem, combined with the lack of good mathematical tools for tackling it, have ensured that it has been, and will continue to be, a major challenge for operations researchers working in mining. This paper reviews the current state of the art in pit optimisation and scheduling algorithms. Starting from the inception of the first block models in the late 1950's, it progresses through the developments and applications of the Moving Cone algorithm, the Lerchs Grossmann 3D Graph Theory algorithm and some of the heuristics, to the new artificial intelligence techniques that are being applied today. Along the way, it discusses the limitations of the various approaches and lays the foundations for the research that is currently being undertaken by CSIRO and others in the field of mine production scheduling and control.

Jan 1, 1996

By R. M. Bricka, T. J. Olin

Heavy metals contamination is an environmental problem at Army installations engaged in firearms training and munitions production. At these facilities, weathering and corrosion of expended munitions and leaching from wastewater lagoons, landfills and burn pits have resulted in heavy metals contamination of the soil. The principal metals encountered in firing-range soils are lead, copper and zinc. Cadmium and other metals, such as antimony, that are often incorporated in the munitions are sometimes seen in lesser concentrations. Mercury is associated with various propellants and, while present in much smaller concentrations, is of concern because of its acute toxicity. Chromium is primarily associated with plating operations. The transport of metals into groundwater has been confirmed at some locations, which has required treatment of the soil and groundwater at these sites. Certain treatment processes for contaminated soil produce metals-laden extracts, which also require treatment before reuse or disposal. Ion exchange is generally quite effective for removing metals from aqueous streams. However, resins are expensive and must be regenerated, and activated carbon is generally less effective for most metals and also requires regeneration. Therefore, alternative effective and economic sorbents are needed. Twelve sorbents were screened in initial batch testing. These included activated carbon, bark, chitosan, crown ether, corn cob, xanthate, clay (kaolinite and montmorillonite), peat moss, seaweed and reagent-grade zeolite (aluminosilicate, Sigma Product No. Z3125). Of these, zeolite demonstrated the highest capacity for Pb, Cr and Cd. For this reason, zeolite was selected for further testing in batch, kinetic and column studies. Materials and methods Zeolite. The zeolite used in the second-phase batch and column studies was obtained from a natural deposit of clinoptilolite-rich rock located in South Dakota (Rocky Ford SDH) (Desborough, 1996). Large blocks of the material were crushed and sieved into the following three particle size ranges: 0.5 to 1.0, 1.0 to 4.0 and 2.0 to 4.7 mm. This material demonstrates high structural stability in acidic solutions (pH 2.5) (Desborough 1996) and has a measured surface area of 30 m2/g. The measured total cation-exchange capacity (TCEC) was approximately 10 meq/100 g. This is well below what has been indicated for commercially available zeolite, which has been reported to be about 180 to 220 meq/ 100 g. The TCEC test was repeated (Method 9081, SW 846) using sodium acetate. The test resulted in a TCEC of 54.5 meq/100 g. The difference between values obtained for this material and published values for zeolites may be attributable to the greater heterogeneity in the material used in this study, compared to commercially available materials, or to the effect of the relatively large particle sizes utilized. Batch studies. Seven batch studies were conducted using synthetic metal solutions and soil extracts (Table 1). Extract composition: The P-extract was prepared by sequential surfactant extraction of organics from a burnpit soil followed by acid extraction of metals. The pH of this solution is approximately 1.1. A number of metals and organic compounds were present in the soil. Analysis of the extract was restricted to Pb, Zn and Cu concentrations for this study. The FBH extract was produced from a firing-range soil that was oxidized with a 0.01 M CaO solution and then extracted with 0.1 M acetic acid. This was filtered through 0.5-µm Whatman No. 5 filter paper and stored at room temperature. The pH of the FBH extract was approximately 4.5. pH Control: Calcium carbonate (CaCO3) may be present in the zeolite horizon or bed. Calcium ion (Ca") is released from the exchange sites when in contact with solutions containing ions for which it is more selective, such as lead. This results in a rise in solution pH over time. Acid washing removes most of the carbonates, eliminating the need for a buffer. Batch studies were conducted using both acid-washed zeolite (AW) and unwashed zeolite (UW) for performance comparison. The UW zeolite was rinsed with distilled deionized (DDI) water to remove fine soil particles. Both materials were dried at 105°C (220°F) overnight, so that the dry mass could be determined. Column studies. Ten column studies were conducted. Because it was expected to have the best hydraulic properties, the largest particle

Jan 1, 1999

Simulation has established itself as an accepted tool for the design and optimization of complex minerals processing plants. This paper addresses the use of simulation as a tool for the design and optimization of carbon-in-pulp and carbon-in-leach (CIP/CIL) plants. The complex, interactive nature of CIP/CIL plants makes detailed experimentation an expensive and time consuming approach to CIP/CIL plant design and/or optimization. This paper discusses a simulation-based software tool that can make the process of CIP/CIL plant design and/or optimization much more cost effective. Many of the issues and problems pertaining to the use of simulation for CIP/CIL design and operation are generic. Thus, this paper also attempts to highlight generic issues that must be solved before simulation will become a more widely used design and optimization tool. Requirements for the application of simulation for CIP/CIL plant design and optimization are highlighted. Similar problems and issues can be identified for most mineral processing plants.

Jan 1, 1994

By Jean-Michel Rendu

In most circumstances, the traditional methods of. ore reserve estimation for large undulating sedimentary deposits, such as coal and iron formations, do not allow the accurate prediction of grade for mining blocks. The problem is Particularly accute when the mining blocks are small with respect to the thickness of the geological zones in the deposit, and when there are significant grade changes between the foot-wall and hanging-wall of these zones. A simple geostatistical model has been developed, which takes into account the grade changes not only in the direction of the geological strata, but also in the direction normal to these strata. The genesis of sedimentary deposits and the resulting geological properties of these deposits were considered in the development of the model. The model has been successfully applied to the evaluation of a large coal deposit. Eventhough some practical difficulties have been encountered, for example when part of a geological zone was missing or had not been sampled, these difficulties have been .resolved. Both the theory and its practical application are presented in this paper.

Jan 1, 1979

The modelling process described in this paper was developed in order to assess the feasibility of various investments options for the exploitation of a lignite deposit located in the Prefecture of Florina, Greece. The model uses as evaluation criterion the net present value. It is based on the characteristics of the reserves and relates the decision making with numerous technical, economic and environmental factors. The examined alternatives include the construction of a new thermal power plant at the mine-mouth, the fuel supply of already existing power plants located at relatively long distances and the fuel exports in neighboring countries. Moreover, the feasibility of post-poning the exploitation of the lignite deposit and preserving its reserves for exploitation in the future is also assessed. The paper also includes a short discussion about the environmental constraints related to the supply of lignite produced from Florina mines to power plants that were designed and constructed for burning fuel mixtures with different quality characteristics.

Jan 1, 2005

By R. F. Hüttl

World-wide Germany is the leading lignite mining nation. Most of the lignite is produced in opencast operations. However, opencast mining causes enormous impacts on natural ecosystems and even on entire landscapes. The extensive production of lignite particularly in eastern Germany results in large devastated areas, which so far have been reclaimed only to some part. For the restoration of the post-mining area of more than 80,000 ha the major land use option is the reestablishment of forest ecosystems. However, adverse site conditions of the post-mining landscape such as extreme soil acidification and salt concentrations call for specific recultivation practices. Therefore, after the German reunification new reclamation and reforestation concepts have been developed for these brown coal areas of eastern Germany by the Collaborative Research Center (SFB 565) at the Brandenburg University of Technology at Cottbus (Germany). As a case study our comprehensive investigations into forest ecosystem development on terra nova in the Lusatian lignite mining district, south-east of Berlin, will be presented.

Jan 1, 2003