Search Documents

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By B. Kendall

"ISSUES ASSOCIATED WITH HAND DRILLING/JACKLEGS In coal mines, hand held air, electric, and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in long wall recovering bolting. In hard rock mines pneumatically powered “jack leg” drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand held hammer due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines. Although the hand-held equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib, and face; tripping hazards; bending twisting lifting hazards; high noise levels; and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator – continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company. Hand held drills also typically have limited thrust and torque capability which limits their ability to push long resin bolts, inadequate torque to properly install resin bolts, or to properly torque mechanical or tensioned rebar bolts. Hand held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or “riding the drill” is limited to 8’ (2.44M)."

Jan 1, 2015

By M. F. Vancas

The San Manuel oxide ore reserve ranges in depth from being exposed on the surface to lying 1000 ft. beneath a conglomerate layer all of which is confined in the subsidence zone of an active sulfide block caving operation. Present day recovery of the oxide copper values is either by open pit mining-dump leaching, or in-situ leaching of the oxide ore using dilute sulfuric acid solutions and solvent extraction/electrowinning processing of the pregnant leach solutions. Future plans are for continuation of leaching with expansion of reserves and increased processing rates. The state of the mining industry and copper in particular has not been good for a number of years. All of the producers that are still operating have made major adjustments in order to remain competitive. Magma Copper Co. is no exception.

Jan 1, 1987

By John Callahan

A stream sediment (minus 80-mesh and minus 60-mesh panned concentrates) and lithogeochdcal survey for gold did not locate any Triassic-age placer deposits in the northern Wadesboro and southern Sanford basins in North Carolina. A stream sediment geochemical program for uranium funded by the North Carolina Energy Institute did identify one and anomalous site (8.5 ppm U; 5 ppm Th) near Covenington, North Carolina and eighteen possibly anomalous sites (1-1.6 ppm U) . Five of the eighteen samples with uranium levels in the 1-1.6 ppm range have high thorium levels (112-853 ppm) and may indicate a monazite source for the uranium. Gold values as high as .83 ppm in the stream sediments and 9.3 ppm in the panned concentrates were obtained during the survey. Small (<.5mm) flattened grains of gold (1-4 grains) were observed along with coarse kyanite and/or monazite in some of the panned concentrates. A distinctive pattern of high gold values in the sediments was observed in the vicinity of Mangum, N. C. where Minard (13) reported values as high as 2.1 ppm £ram a Triassic lithology. Follow-up gold analyses on over 400 rock samples from twenty-eight exposures near Mangum failed to obtain any high values (<55 ppb). The presence of coarse kyanite, monazite and gold in panned concentrates may be from a source younger than the Triassic lithologies that the streams currently drain or adjacent Paleozoic rocks.

Jan 1, 1979

By L. R. Hossner

Chemical and physical properties of surface soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the existing surface soils, especially when these soils are classed as prime farm lands. In Texas, materials from the Carrizo, Calvert Bluff, Simsboro, and Hooper Formations overlie the lignite. The Carrizo Formation consists of thick clean sands with poor water and nutrient retention capabilities. These materials are least suited for placement of the surface of reclaimed land. The oxidized, medium textured overburden from the Calvert Bluff and Simsboro Formations possess adequate water and nutrient properties and are better suited for sustained plant growth. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation. However, caution must be exercised in vegetating these materials since they may contain acid forming sulfide minerals.

Jan 1, 1982

By Burt Ensley, Viatcheslav Dushenkov, Ilya Raskin, David E. Salt

Roots of many hydroponically grown terrestrial plants, including sunflower (Helianthus annuus L.) effectively remove toxic metals such as Cu+2, Cd+2, Cr+6, Ni+2, Pb+2 and Zn+2 2 from aqueous solutions. It should be possible to scale up this process such that plant roots can be used to treat large volume aqueous waste streams. It can be extrapolated from laboratory results that to reduce the Cd concentration in a waste stream, from 1 ppm to below 4 ppb, with a flow rate of 4000 L/min, would require 3500 sq. m of plant roots with a density 5 kg fresh weight per sq. m. These results suggest that the roots of hydroponically grown terrestrial plants may provide an attractive alternative to the accepted water treatment technologies.

Jan 1, 1995

By Annan Cook

J.R. Atkinson, office engineer to Kennecott Copper Corp., summarized data on the Mineral Park area [Wallapai (Chloride) Mining District, Mohave County, Arizona, Fig. 1] and submitted it to the New York office in 1950. He recommended an examination. Weston Bourret, a Kennecott geologist, accompanied by B.S. Butler, the well known former US Geological Survey geologist, examined the larger of two hydrothermally altered areas in Mineral Park that same year. Bourret recommended that the property be optioned and mapped. Georges Ordonez, Kennecott&apos;s chief geologist, after a field examination, agreed with Bourret&apos;s conclusions At the end of the summer of 1951, Annan Cook (another Kennecott geologist) accompanied Ordonez to the property prior to starting a mapping program. At Ithaca Peak, the structure, alteration, and reddish-brown coloring in leached cavities-hematite, jarosite, and goethite with minor copper staining - made an interesting target. The Peak, which has since been mined, was a Laramide quartz monzonite porphyry grading into quartz porphyry, penetrating Precambrian rocks. Turquoise had been mined from several workings on the Peak. Surrounding the central area of alteration, but mainly to the northwest, there were many long-abandoned underground workings mined for zinc, lead, gold, silver, and copper. To the west of Ithaca Peak within the main area of alteration, surface evidence of a chum drill hole suggested interest in the disseminated mineralization probably prior to World War II. A topographic and geologic survey of the altered Ithaca Peak area was initiated by Cook in September 1951. He was assisted by Richard Vosburgh, field engineer, and by four geologists: Charles Goddard, III, Donlon LoBionda, Keith Martin, and A.T. Stone. When Cook returned to New York, Vosburgh was left in charge. Mapping continued and diamond drilling took place during the winter of 1951-1952. Drill sites were selected entirely on the basis of surface geology. Five drill holes, including a flat hole, located around the flanks of Ithaca Peak, averaged about 183 m (600 ft) in length. A sixth hole caved at less than 60 m (200 ft). The best values obtained were in the first hole (-45°): 90 m (300 ft) averaged 0.62% copper and 103 m (337 ft) averaged 0.041% molybdenum. In another hole, 43 m (142 ft) averaged 1.09% copper and 0:023% molybdenum. The values of copper and molybdenum in these two holes were generally higher than in the remaining holes, although molybdenum values were always around 0.024% or better. The New York office decided, however, to abandon the project even though the remaining field crew of three had recommended more drilling.

Jan 1, 1991

By S. J. Jung

The stability of underground openings for deep mines is critical, since incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress concentrations. Current state-of-the-art procedures for the design of underground openings are largely based on rules of thumb, experience, and trial and error. Rules of thumb are invariably based on the past experience of the designer and may not remain optimal as the depth and complexity of mine workings increase. Often, as conditions change, and as the interaction between geology, in-situ stress conditions, and mine openings grows more complex, the cost of maintaining structural integrity becomes prohibitive. Existing design procedures for deep mines are rapidly becoming inadequate as mines are worked at greater depths. For example, in the Coeur d&apos; Alene Mining District, several million dollars are spent for inspection, repair, and maintenance on a regular schedule, largely as a result of inadequate design. In these types of situations, it is of critical importance that a new design methodology be developed for the layout and design of underground openings.

Jan 1, 1994

By Julius Rubinstein, Victor Badenicov

The development of column flotation is the most significant achievement in the area of mineral processing in the last few decades. The high efficiency of column flotation allows a reduction in process time, a decrease in the number of cleaner stages and in the volume of the circulating load in the flotation circuit, and, as a result of this, an increase in consistency and reliability of operations. Unique multisectional column flotation apparatuses were developed. Such designs have a number of essential advantages as compared to monocells. A change from monocells to multisectional column allows to provide favourable conditions for separation of particles of various floatability. To attain that aim particular hydrodynamics and aeration regime is established in each section of the column, operational variables being adjusted according to the floatability of the material. Therefore in multisectional column machines the material-apparatus feedback can be established, process variables optimized depending on the characteristics of the floated materials. This concept forms the basis of column designs we have developed. For the first time column cell with alternating slurry Rows (combination of co- and counter-current flows) were developed and commercialized . Successful operation was reported of the new generation of columns with cell volumes of 10 to 80 m3 and the height of 4-6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants. Operation experience of these cells showed their considerable design and operational advantages and verified the proposed options and relationships. The new apparatus is provided with a pneumohydraulic aerator allowing to control bubble size distribution, the service life of the aerator is not less than two years. A multilevel flotation model was developed and used to work out a technique of column design and process parameters calculation. A method of the apparatus design parameters calculation based on laboratory test results (scaling up) was worked out. The method is based on flotation macro and micro-hydrodynamics simulation.

Jan 1, 1995

By A. Zutshi

Production of CO2 is an inevitable consequence of burning fossil fuels, with the only CO2 sequestration technique feasible in the immediate future being its injection in various geologic media. This paper discusses the factors that influence the injection, movement, and storage of CO2 into deep coal seams, while simultaneously increasing the production of methane. The results of a laboratory-scale study to evaluate the movement of CO2 in coal, its ability to displace methane, and the capacity of coal to retain CO2 are presented. The findings are compared with observations at one of the two field-scale pilot operations practicing CO2 injection in coal. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2006

By Alejandro Sanz, Juan Luis Magro, David Mazeyrie

The Hampton Roads Bridge-Tunnel Expansion Project (HRBT), initiated by the Virginia Department of Transportation (VDOT), will add two new 1.5-mile TBM bored tunnels to the two existing immersed-tube tunnels between artificial islands, part of the connection between Norfolk and Hampton under the Hampton Roads Harbor in Virginia, USA. The new bored tunnels will be built by Hampton Roads Connector Partners (HRCP), a joint venture of Dragados USA, Vinci Construction, Flatiron Constructors and Dodin Campenon Bernard. This paper covers technical discussions that led HRCP to select a Variable Density TBM to address the challenges of this tunnel project, including but not limited to (i) the diameter of the bore: a 46 feet (14.04 m) diameter machine that constitutes the second-largest TBM ever used in the United States; (ii) shallow ground-cover under the water table; (iii) challenging and varying geology along the alignment, with mixed-face conditions and different types of ground modification zones; and (iv) the high TBM operating pressures required—all these and other challenges in a sensitive marine environment.

Jun 13, 2021

By Lauren M. Roberts, Ralph R. Sacrison

The Meikle Mine uses long-hole open stoping and cut-and-fill methods with backfill as the primary ground support technique. The mine operates at 2,858 tonnes per day (3,150 tpd) and has sustained operation in excess of 3,175 tonnes per day (3,500 tpd). Consistent backfill production is critical in achieving these mining rates. The heart of the system is a 7.65 cubic meter (10-cyd) horizontal shaft ribbon mixer located 328 m (1,075 ft) underground. System control is through several PLC&apos;s, allowing for a high degree of automation and process flexibility. Aggregate feed is routed 257 m (842 A) through vertical drop pipes in the ventilation shaft, a rockbox, transfer raises, and then into either of two raisebored storage silos. The aggregate is crushed mine waste, nominally 70% 3.8 cm x 1.0 cm (1-1/2"x 3/8") and 30% -1.0 cm (- 3/8"). The binder is routed through a vertical borehole, surge bins, and transfer raises. The binder is a mixture of Type II cement and fly ash. Two primary manufactured fill designs are produced: a high strength mix for stopes which will be undercut; and a low strength mix for stopes with only rib exposure. The high strength target is 5.5 Mpa (800psi) unconfined compressive strength in test cylinders. The low strength target is 2.8 Mpa (400 psi). The systim has allowed consistent achievement of these targets, while experience has allowed reduced costs and increased efficiencies. Fill placement is through 6.1 cubic meter (8 cyd) LHD&apos;s dumping into stopes. Specific sills and cut-and-fill drifts are jammed to the back. System enhancements have included colloidal mixers for cemented waste slurry placement and transfer raises for sending manufactured fill to the lower levels of the mine.

Jan 1, 2001

By Lawrence Tsang, Conrad Ng, Tim Leung, Peter Poon

"The Mined Tunnel is part of the Central-Wan Chai Bypass and Island Eastern Corridor Link (CWB), which is a strategic road along the northshore of Hong Kong Island targeted to alleviate the heavy traffic congestion. The objective of this paper is to review the performance of construction of a 160m long Mined Tunnel with a trinocular cross-section area of 460m3 and a combined span of about 50m underneath the southern approach ramp of the existing Cross Harbour Tunnel (CHT) by sequential excavation method (SEM) in hard rock. Mechanical excavation of tunnel by adopting the New Austrian Tunnelling Method (NATM), together with the application of NGI Q-system allows observational approach and optimization of temporary rock support design. Furthermore, the good performance of optimized rock support and the stability of CHT are confirmed through instrumentation monitoring review. This paper also discusses the selection of different tunnel plant and equipment to achieve the planned rates of tunnelling by mechanical excavation in competent granitic rock. INTRODUCTION The works of the CWB mainly comprise construction of 4.5km dual three-lane trunk road, of which a 3.7km section is a tunnel connecting Rumsey Street Flyover in Central to Island Eastern Corridor at North Point (see Figure 1). The Mined Tunnel runs from the ex-Public Cargo Working Area (ex-PCWA), underneath the existing CHT, and through the Causeway Bay Typhoon Shelter. The Mined Tunnel passes at an oblique angle beneath the southern portal of CHT over a length of some 50m. CHT is the primary sensitive receiver of this project and is utilized with a daily throughput of about 120,000 vehicles that far exceeds the design capacity of 78,000 vehicles per day. Hence it is necessary to choose the most appropriate tunnelling method to preserve the structural integrity of the CHT. Other sensitive receivers in the vicinity include structures to the north of the Mined Tunnel, the Royal Hong Kong Yacht Club (RHKYC); and to the south of the Mined Tunnel, the Police Officers’ Club (POC)."

Jan 1, 2016

By Pinar Eksert, Hakan Akcin

Investigations show that injuries and fatalities in mining workplaces in developing countries are increasing. In Turkey, the number of workers killed in occupational accidents in the Zonguldak Hard Coal production region per 100,000 tons of coal production is 2.83 in the private sector and 2.03 in the public sector. For this reason, it is important to conduct risk analyses in terms of occupational health and safety and to implement measures quickly. Risks are evaluated with reactive and proactive approaches. Because hazards and events are often unpredictable in high-risk areas such as coal mining, it is not practical or meaningful to plan proactively in advance for every possible situation underground, especially psychosocial risks. However, it is important to develop protective strategies and measures for unexpected events or to take a reactive approach to prevent future incidents or accidents and to identify psychosocial risks. Therefore, reactive risk assessments based on the tactics and strategies of criminology can be conducted and spatiotemporal geographic information system (GIS) techniques can be utilized, enabling managers in mining workplaces to correct assessments.

Oct 1, 2024

By N. Duru

"Gravity concentration is still a challenging area in the mineral industry. This is mainly because of the fine size valuable mineral losses to the tailings during its application. But the recent developments in centrifugal separation methods and their mutual application with conventional separation techniques has increased mineral recoveries. In this paper, field application of conventional gravity separation methods with the combination of 2” diameter hydrocyclone cluster unit and a multi gravity separator (MGS) was discussed. Additionally, particle size distribution and chromite content of the plant streams is presented and initial laboratory test results were compared with the actual plant data throughout the paper. As expected, field data showed derivations from the laboratory tests but the combination of MGS and conventional gravity separation techniques resulted in gravity separation of -0.1 mm chromite particles. INTRODUCTION The purpose of this mineral processing plant project was to investigate the possibility of upgrading chromite ore from 12% to 48% Cr2O3 and having final tailings assay as 2% Cr2O3. For this reason, initially a set of laboratory gravity separation studies were conducted to evaluate the performance of combination of 2” diameter hydrocyclone cluster and multigravity separator. After obtaining successful results from the laboratory work, a feasibility study was initiated. Economical results of the feasibility study showed that an achievable high net present and return on investment values. Following the investment decision; engineering, equipment procurement, construction of the processing plant was completed in eighteen months. This paper focuses on the initial laboratory test work results, operational data of the 2” diameter hydrocyclones and MGS units; resulted chromite recoveries. Processed ore has the chromite associated with serpentine and olivine minerals. The chromite particles are generally in round shapes with sizes between 50 µm to 1600 µm and average size of 450 µm. The microscope images of the chromite and associated formations are presented on Figure 1.Chromite is formed in mixture with iron oxides, with varying amounts of magnesium, aluminum. The average chemical composition of the representative drill core samples of the ore deposit is given on Table 1."

Jan 1, 2017

By Timothy Batchler, Khaled Mohamed, Morgan Sears

The National Institute for Occupational Safety and Health (NIOSH) initiated a testing program to assess the effects of lateral loading on various standing supports used in underground coal mines. This study is not intended to endorse a particular type of standing supports nor to provide a comparison between different types of standing supports. This paper aims to measure the lateral loading capacity of two types of standing supports and evaluate how it affects their vertical loading capacity and yielding mechanisms. The study utilizes the Mine Roof Simulator (MRS) at NIOSH Pittsburgh. Type-1 support is characterized by telescopic tubes made from ASTM A-513 steel with a specified locking mechanism, and Type-2 support comprises a single component constructed from ASTM A500 Welded Grade C pipe. Vertical load tests were carried out to assess the designed performance of Type-1 and Type-2 props. Type-1 props demonstrated a "constant yielding" behavior, achieving an ultimate capacity of up to 140 kips. Type-2 props showed a "load shedding" behavior, reaching peak verti- cal loads of up to 191 kips. Buckling analysis revealed that Type-1 props were not designed to buckle, and Type-2 props failed due to buck- ling rather than material yielding. Under vertical pre-loading, lateral loading tests showed that Type-1 props can withstand about 9 kips, and Type-2 props can withstand about 10.79 kips of lateral load. This represents roughly 6% of their vertical loading capacities. Testing props under lateral loads in addition to their intended vertical loads showed that the lateral loads could influence their loading mechanisms. Type-1 props did not exhibit the expected "constant yielding" behavior under lateral load but instead showed "load shedding" decreasing their rated vertical capacity by 70%. At high vertical pre-loading, Type-2 props demonstrated "constant yielding" behavior instead of the anticipated "load shedding," leading to a 60% reduction in their rated vertical capacity. These findings provide valuable insights into the behavior of these props under different loading conditions, aiding in their efficient use and design in underground mining operations.

Jun 25, 2024

By A. W. Wensel

The adsorption behavior of sodium oleate on brucite, Mg (OH)2, has been studied by Fourier transform infrared spectroscopy. Both internal reflection and diffuse reflection (DRIFT) methods were used to characterize the adsorbed oleate on brucite. DRIFT measurements were shown to be quantitative, and an equilibrium adsorption isotherm was obtained. The conformational behavior of the adsorbed oleate was investigated as a function of adsorption density. It was found that at sub-monolayer coverage the alkyl chains of the adsorbed oleate had more ?gauche? character than at multi-layer coverages. Also, DRIFT spectra revealed that the adsorbed species were magnesium dioleate. For internal reflection measurements single crystals of MgO were hydrolyzed to form a thin Mg (OH)2 layer.

Jan 1, 1994

By M. A. Alan

The Bellavista Gold Deposit lies 75 Kms north west of San Jose, the capital of Costa Rica, Central America and 3 Kms north east of Miramar, in the Province of Puntarenas. The total road distance from San Jose to the deposit is 120 Kms all paved road except for a 2.5 Km graded, gravel road on the property (Figure 1). Infrastructure services in the Miramar-Puntarenas area are well developed with electrical power distribution, a modern port facility and community services being available. The deposit lies on the south west flank of the Tilaran Mountain Range between an elevation of 550 and 800 meters above sea level. The local topography is steep, originally covered with pre-montaine, tropical wet forest vegetation which has been largely destroyed due to clearing for cattle grazing. The annual rainfall is approximately 2,950 mms, 90% of which occurs between May and October.

Jan 1, 1992

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991