Search Documents

By S. E. Phillipson

The MSHA Technical Support, Roof Control Division's primary evaluation tool for coal pillar designs is the Analysis of Coal Pillar Stability (ACPS) program. However, ACPS is limited to evaluating interactions between two seams at a time, which is not ideal for complex multiple- seam scenarios. Further, it does not recognize the influence of strata properties in the interburden and cannot be used to evaluate individual pillars. We apply the Rocscience RS2 two-dimensional finite element program as a complement to ACPS. Complex multiple-seam scenarios can be characterized by a modified pillar stability factor where the ACPS single-seam development pillar stability factor is multiplied by the ratio of average single-seam development stress to the stress in the critical pillar at the multiple-seam stage, using the values of o as predicted by RS2. Several series of test examples involving two-seam analyses with isolated remnants, gob-solid boundaries, and high extraction areas of varying width were used to calibrate simulated gob properties such that the ACPS+RS2 method generated results that matched a traditional ACPS Stability Factor to within 13%. As high-extraction areas become wider and deeper, progressively stiffer gob is simulated by increasing the Young's Modulus property in RS2. After achieving calibration with the test series, three examples of complex multiple-seam scenarios were evaluated, using reasonable properties for strata types and thicknesses based on core log data. Resulting modified stability factors are reasonably close to those predicted by ACPS, although affected by units of sandstone in the interburden and gob shadows superimposed on remnant structures. This tends to show that even in complex multiple-seam conditions, applying ACPS to the worst-case interaction should usually result in an acceptable pillar design.

Jun 25, 2024

By Joseph Lynch, John DiPonio

This report refers to the Chicago Deep Tunnel Contract 13A, which was the first contract let in the City of Chicago requiring the construction of deep drop shafts for the transportation of high level sewage to the deep tunnel system. The basic contract required the contractor to construct certain drop shafts designed to deliver surface and high level sewage to the deep tunnel system approximately two hundred feet below. The design of the drop shafts was in a degree affected by their proximity to the existing deep tunnel. The tunnel, approximately three and one-half miles long, was to have five shafts dropping sewage at five locations. Four of the drops were approximately one-half mile apart and spaced from the dead end of the tunnel. One shaft divided the remaining two miles from the existing work shaft at the southeast end of the tunnel wherein a 220' deep pumping station was to be built. The existing tunnel had been built some time previously and all dewatering had stopped, allowing the tunnel and main shaft to fill with water. According to the plans, the drop shafts were all between fifty and ninety feet north or south of tunnel center line, and located in heavily built-up residential and industrial property. This then defines the problems: How do we control the water. If we excavate from the top down, how do we handle the slurry and the muck from five locations. How shall we construct the connecting tunnel between

Jan 1, 1997

By S. K. Kawatra, T. C. Eisele

Pyrite depression is of great interest in sulfide mineral flotation, where pyrite is a common gangue mineral. Since the floatability of pyrite is a function of the pH and a variety of other chemical factors, pH control is a critical part of sulfide flotation circuits. A wide variety of pyrite-depressing chemicals have been studied and used in sulfide- mineral processing, with considerable success. However, there are certain applications where there are still no satisfactory pyrite depressants, and even when suitable depressants are available, there is always a need for less-expensive reagents. Microorganisms, such as the bacteria Thiobacillus ferrooxidans, are known to depress pyrite flotation. However, the dependence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms, and the effect of pH, has been examined. Screening tests using microflotation showed that every microorganism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with two of the screened organisms and two different pyrites showed that microorganisms are very effective depressants at acid pH, but are largely ineffective at neutral and alkaline pH where the pyrite surface is not naturally hydrophobic.

Jan 1, 1994

By Paul G. Schmidt

The Crandon massive sulfide deposit Forest County, Wisconsin, was discovered by Exxon Minerals Company, U.S.A., in July 1975. Announced estimated in-place reserves are 62 M metric tons (70 million short tons), grading about 5% zinc and 1% copper. The reserves are evenly divided between massive sulfide are and stringer sulfide ore. The sulfide body is associated with Precambrian felsic pyroclastic rocks, and it is overlain by intermediate volcanic rocks and their derived sedimentary rocks. These rocks were subjected to greenschist facies metamorphism and were tilted to a near-vertical attitude. Geologic observations indicate a submarine-volcanic-exhalative origin for this deposit.

Jan 1, 1978

By I. Iwasaki, H. Dho

Two aromatic-type chelating agents, 1,10 phenanthroline (phen) and 8-quinolinol (quip), were tested as specific depressants for magnetite in the cationic silica flotation of magnetic taconite concentrates. Micro and batch flotation tests, along with zeta potential and adsorption measurements, were used. In the presence of a cationic collector, dodecylammonium chloride (DAC), the Fe/phen surface chelate electrostatically repelled DAC, and the magnetite was depressed. The negatively charged Fe(quin)2(OH)2- on the magnetite surface attracted the cationic collector and made magnetite floatable.

Jan 1, 1997

By Paul Mitchell, Amy Wheaton, James Rybock

Acid rock drainage (ARD) represents one of the most intractable problems faced by the non-ferrous metal and coal mining sectors, and the creation in the recent past of a number of high-level national and international initiatives reflects the growing concerns of industry, government and other stakeholder groups. ARD is certainly considered one of the most serious environmental impacts caused by mining and the industry's greatest environment-related technical challenge. Additionally, the global depletion of non-acid generating oxide ore deposits and the increasing dominance of sulphide ores means that the potential for ARD incidents will continue to increase. Once initiated, the cycle of chemically and biologically mediated and catalysed reactions leading to ARD generation is difficult to stop. While there is evidence to suggest that the degree of contamination of ARD will decrease rapidly within a relatively short timeframe (Wood et al., 1999), experience in historic mining regions of the world indicates that the problem may persist for centuries at certain sites. Current best practice in dealing with ARD puts the emphasis on prediction and prevention, planned from the outset of the operation and integrated with each phase of the mine site life cycle. The elements that constitute best practice are becoming more clearly defined and as this process of clarification continues industry will undoubtedly accelerate the process of best practice implementation, burying at last the image of mining as a despoiler and polluter of landscapes, an image based on past, rather than current, practices. However, it is equally clear that despite the best efforts of industry and regulators, many sites will continue to generate ARD during operation and following closure - in many cases, a legacy of ARD has been derived from operational and strategic decisions made decades ago, before the risks and impacts of the self-sustaining cycle of ARD generation were properly understood. Add to this ARD generation from poorly managed operations and from historic and abandoned sites, and it becomes clear that the treatment of ARD will be required for the foreseeable future to protect water quality, and ecosystem and human health.

Jan 1, 1999

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023

By Robert A. Jankowski, Fred N. Kissell

Recent allegations about tampering of coal mine dust samples have led to suggestions that the coal industry needs a respirable dust compliance sampling method that is less subject to tampering. The sampler designs under consideration include fixed location monitors that could be mounted on a mining machine or located at a stationary location in the mine, and samplers that are worn, like the existing samplers. Fixed-point samplers have a design advantage, since samplers worn on the body will have size and weight limitations. On the other hand, in some cases there are respirable dust concentration gradients, which will dictate careful placement of a fixed-point sampler inlet to determine the exposure of workers. This study examined dust concentration-gradient data obtained by the Bureau of Mines and others over the last decade. As an example of spatial gradients at continuous miners, a fixed-point monitor located in front of the operators cab shows a higher dust concentration than a sampler located on the operator and reduced exposure when the sampling location is behind the operator cab. It may be necessary to use a sampling tube with a machine mounted monitor, to sample in the operators breathing zone in the cab to provide a more representative sample of the miners exposure. For face workers on longwalls or on continuous miner sections using remote control, the study shows significant dust level gradients and gradient variations between typical operator positions and mining machine locations. In addition, if fixed-point monitoring is used to monitor an area, vs the exposure of specific workers, dust control technologies currently employed to ensure reduced dust exposure such as the diversion of dust laden air away from the workers, or through the use of remote control of mining machinery may not indicate the same dust reduction obtained with current sampling techniques.

Jan 1, 1993

By Sunil Jain, Jan M. Mutmansky

As coal mining evolves in this country, underground coal is being mined at greater depth and under more difficult conditions than in the past. At the same time, economic conditions make it necessary to mine more efficiently and economically. As a result, pressures on mining companies arise on two fronts and make the job of mining coal underground very difficult. Recent improvements that have been made in health, safety and productivity have come about primarily due to improvements in existing technology and better management of all the production resources. However, this trend can continue only so far and thus innovation will be needed to continue the improvement. This paper deals with a concept that, on the surface, appears to be more efficient in terms of the costs to provide ventilation. The resulting design is oriented toward increasing the ventilation efficiency through use of a unidirectional ventilation plan but it also promises to increase recovery and decrease the requirements for development entries. To analyze this ventilation concept, two mine layouts with a similar production schedule were planned in a hypothetical 1.83 m (6 ft) coal seam. The first alternative analyzed uses a traditional approach to ventilation with centrally located shafts and a bidirectional ventilation pattern. Using this system, it is necessary to use large-diameter shafts and a large number of main entries. Using the same assumptions on ventilation requirements, the second alternative utilizes unidirectional ventilation whenever possible, a smaller number of main entries and small-diameter blind-bored shafts in the bleeder areas. The comparative analysis is performed using PSU/TDMVS, a computer network analysis program that is capable of determining the ventilation power requirements at any time in the mine life and converting the costs to a present value. The economic analysis is then completed by including the shaft-sinking and entry-driving costs and the costs associated with the recovery of coal that are directly related to the change in the ventilation system. The results are summarized on a present-value basis.

Jan 1, 1987

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By D. R. Spears, C. E. Jordan

In an effort to improve flotation efficiency of the domestic minerals industry, the US Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20- µm, minus 625 mesh). The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine-particle, turbulent-flotation model. For the mineral system tested, improved flotation response was obtained in the laboratory testing with small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1991

By Russell L. Dahl

In a continuing effort to improve plant efficiency, United States Steel's Atlantic City Ore Operations completed the rubber lining of its balling drums in late 1982. This resulted in benefits of reduced bentonite consumption, reduced maintenance costs, improved production rates, and lower power consumption. These advantages far outweigh the disadvantages of increased oversize production and increased surging on the roll screen sizing devices. Certain operating characteristics and variables are discussed herein.

Jan 1, 1983

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By Charles E. Joachim

Current Army tunnel destruction criteria (1) are based on limited nuclear-explosive (NE) and high-explosive (HE) test data. The PILE DRIVER (2) and HARDHAT (3) events investigated tunnel and support system response where yields were relatively large and tunnel diameter small compared to typical underground openings and localized stress fields of low yield weapons. Some limited tunnel destruction information was obtained from underground events of the PLUMBBOB and HARDTACK II Series (4). These events used access drifts which were designed to be self closing at the weapon point. The limited NE data are augmented by HE results from the Underground Explosion Test (UET) Program, a series of model and prototype-scale experiments in granite and sandstone (5). Weapon standoff distances (charge c.g. to tunnel wall) were at or near the maximum for major damage. Limited tunnel destruction was produced by a series of hasty and deliberate tests (6) on abandoned railroad tunnels in basalt. Additional HE data were obtained from model tests at the Waterways Experiment Station (WES) (7) using 2.1 MJ (2 lb) TNT charges and tunnel diameters varying from 3 to 17 cm (1.2 to 6.6 in). Recent laboratory scale HE experiments (8) conducted at the WES under the ESSEX program investigated the effects of tunnel diameter, standoff distance, charge confinement, material strength and to a limited extent, tunnel spacing and liner strength variations on tunnel damage. This paper summarizes the analysis conducted to develop predictions for the effects of low-yield nuclear weapons against tunnels and underground openings in rock.

Jan 1, 1979

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By Harry Asche

Tunnels are frequently specified by owners to be designed to a structural code, often a bridge code. In the USA, AASHTO have created a tunnel code, based on structural principles, the AASHTO LRFD Tunnel Design Specification. The Load Resistance Factor Design method (LRFD) described in the AASHTO title is an approximation to the probabilistic design of structures, based on the independence of load and resistance. This methodology is well known to be problematic in geotechnical design, but it is widely used. The paper considers the difficulties of this approach and describes alternative approaches that would result in more appropriate designs for tunnels.

Jun 13, 2021

By E. Topuz, C. Patrick

Longwall face-to-face equipment transfers or moves are the largest source of nonproductive time in a long wall-mining system. Detailed planning and resourceful thinking are paramount for economical, safe and timely longwall moves. New equipment and innovative techniques are frequently tested to reduce overall more time. Determining the cost-effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project-duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several ideas.

Jan 1, 1996

By Michael Rehbock-Sander, Romed Insam

"INTRODUCTIONThe idea of building a summit tunnel under the Brenner occurred to the Italian engineer Giovanni Qualizza as far back as 1847. But it was to be another 160 years to pass before a base tunnel was to be built.In 1971 the idea of a tunnel at the Brenner was dusted off again. The UIC, the International Union of Railways, commissioned a study for a new Brenner railway with a base tunnel. By 1989 three feasibility studies had been drawn up which formed the basis for further planning of the Brenner Base Tunnel.This was the start of the planning activities. In 1994, the European Union included the Berlin-Naples corridor in the list of priority projects. Ten years later, Austria and Italy signed a State Treaty to build the Brenner Base Tunnel. In that same year, what is today the BBT SE was established.PROJECT DESCRIPTIONThe Brenner Base Tunnel (BBT) with a length of 55 km is the centrepiece of the Helsinki-Valletta Transeuropean Traffic Corridor from Finland to Southern Italy. The BBT tunnel system connects in the north with the Innsbruck station (Austria) as well as to the feeder routes in the Lower Inn Valley, and opens to the south with the projected new line in the direction of Verona (Italy). The tangible design efforts have been underway since 1999; the start of construction of the first section was in the year 2007. The project is financed by the Italian and Austrian governments (each 30 %), as well as by the European Union (40 %).From 2027 onwards the Brenner base tunnel, including the existing lines connected with it, will carry a daily average of 330 trains (approx. 80% cargo trains and 20% passenger trains)."

Jan 1, 2016

By Salt Lake City Research Center, D. G. Foot, J. D. McKay

As part of its research program on column flotation, the Bureau of Mines, Salt Lake City Research Center has performed studies on (1) column flotation amenability and comparison with conventional flotation results for over 15 mineral systems, (2) alternative methods for improving column bubble generation systems, (3) mineral behavior within a column, and (4) the effect of changes in column operating parameters on flotation grade and recovery. Based on results from these studies, flotation columns (1) are capable of producing higher grade concentrates in fewer stages than conventional flotation cells at equivalent or increased recoveries, (2) require less retention time than conventional flotation cells, and (3) can be divided into cleaning and collection zones that have characteristic mineral-upgrading-per-foot values. Attempts to improve the column air sparger have led to the development of a superior external bubble generation system, which can (1) achieve increased air holdups. (2) produce bubbles from 400 Um to 4,000 Um average bubble diameter with minimal frother addition, (3) provide superior bubble size control, and (4) be maintained without column shutdown. Efforts are continuing to improve column flotation and transfer successful technology to industry.

Jan 1, 1988