Search Documents

By Harold E. Goetzman, Blair R. Benner, Shaolin Zhong, Rodney L. Bleifuss

A commercial high pressure roller press (KHD 90125) was installed at the Coleraine Minerals Research Laboratory for testing in October, 1994. Pilot plant evaluation of the high pressure roller press has shown that it can be used as an alternative to the rod mill for the comminution of taconite. A series of pilot plant tests were run to compare roller press products to rod mill products in a simulated taconite flowsheet using magnet separation and closed circuit ball milling. Further investigation of a hybrid grinding system, roller press crushing followed by ball mill grinding, indicate that the combination may represent the most energy efficient system for taconite processing.

Jan 1, 1998

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By Z. Kowalski

Landfilling of waste causes the degradation of natural environment, not only due to land occupation, but also due to pollution of air, water and soil. The flotation waste from zinc-lead industry also poses such problem. There is a need to find the way to utilise substantial amount of these wastes and backfilling seems to be a good solution. Recently, in Poland only sand was used for backfilling. However, it will be more beneficial to substitute the sand with the industrial solid waste, especially flotation waste. The tests were performed in the laboratory to examine the use of flotation waste as a main ingredient for backfilling. The use of flotation waste is possible only when it is combined with other waste with specific bonding properties, especially regarding the prevention of leakage. The outcome of tests shows that flotation waste combined with cement and fly ashes can be used as a backfilling material. This paper presents the preparation of flotation waste for using it for backfilling.

Jan 1, 2006

By Bo Forsman

The computer program SYGRISIS estimates number of units of equipment and operating costs on the basis of yearly production for different loading (wheel loader, LHD, digging arm loader) and transport (truck, train, conveyor belt, hoist, pump) equipment either individually or in any specified combination. Input data are yearly capacity, working time and technical data for the equipment. For the cost analysis input data are technical quantities and unit costs. SYGRISIS is written in TURBO Pascal and can be used on IBM compatible PCs with MS-DOS operating system.

Jan 1, 1989

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation will be described. The applicability of the Washburn equation for surface energy evaluation in such systems will be discussed. Key words: Wettability, Powders, Capillary rise, Surface chemistry

Jan 1, 2003

By Lee W. Saperstein

The Research Council of SME, at its Annual Meeting in Reno, NR, in February 1993, held a Research Forum on Technology for the Future. The Forum's purpose was to find out from the members, particularly those from industry, their opinions on research needed in the mineral industries. Panelists were selected for their breadth of knowledge and connections. Many panelists, in turn, solicited opinions from additional contacts. A similar effort is underway with mineral-oriented schools. A parallel mission has been undertaken by the American Mining Congress (AMC) through its Committee on Technology. In particular, AMC is concerned that the needs of industry be transmitted in a timely way to federal agencies, especially the US Bureau of Mines. This article reports to the SME membership the principal findings of the Research Forum. The article is derived from a full report that is available from SME. Many of the calls for research made during the Forum can be clustered into five broad categories. These categories are discussed in the following sections of this article. However, since the time of the Forum, many reviewers of the full report have noticed that fundamental research was not given much emphasis. The Research Council points out that the Forum was organized around industrial needs. There is a call to the academic and research community to organize a similar Forum. The Council emphasizes that this is not the last word on research needs and that the membership is urged to continue to give ideas and opinions to the SME Research Council. There will be an opportunity at its next meeting during the SME Annual Meeting in Albuquerque, NM, Feb. 22, 1994, for open discussion of this report. Because the opinions were intentionally confined to representatives from industry, the problems portrayed and the solutions sought are from the vantage of an operator. It comes as no surprise that many of the espoused research desiderata seek more efficient or cost-effective outcomes for the various mining activities discussed. The order of the Forum was a straightforward set of mining activities: exploration, evaluation, mining and processing.

Jan 1, 1993

By J. M. Scharer, Bruce E. Halbert, Pettit. Carol M., Lysane Bolduc

The ratio of neutralization potential (NP) to acid production (AP) ratio is often employed for predicting acidic discharges from waste rock dumps. The available NP was evaluated in laboratory studies of limestone dissolution in simulated acidic mine water. The available neutralization potential strongly depended on the particle size. Using limestone particles of 114" (6.4 mm) or greater, less than 20% of the total neutralization potential was exhausted at the onset of acid conditions. Apparently, the dissolution of limestone became mass transfer limited. Under mass transfer limitations, the rate of pyrite oxidation may exceed the rate of neutralization by buffering minerals. The implications concerning the controls on limestone dissolution were examined using a geochemical predictive model for sulphide mineral oxidation in waste rock. The results have shown that in case of heterogeneous waste rock piles the NP/AP ratio is a reliable indicator for short-tam predictions only. Kinetic data on the depletion rate of the neutralizing minerals and geochemical modelling suggest that waste rock environments with NP/AP ratios as high as 5.0 may turn acidic in the long term.

Jan 1, 2000

By Trevor A. Moss

Installation of equipment and structures at mines often requires mine planners to evaluate unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. Most planners understand the necessity of employing sound civil, structural and mechanical engineering techniques to design these structures and equipment. However, the influence of geotechnical factors on the overall progress of construction and operation is less appreciated. Mine operators routinely perform exploratory drilling to define ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation - requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine, and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above-surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. However, near surface exploration for the purposes of assessing soil and rock conditions for foundations is often given a reduced priority and less consideration. This article provides an outline of the benefits and importance of performing such exploration. References here relate particularly to shaft headframes, hoists and shaft collars. But the issues raised apply equally to other installations of a similar nature, including milling equipment.

Jan 1, 1992

By Steven J. Schafrik, Michael Karmis, Zacharias Agioutantis

3-D or pseudo 3-D visualization of orebodies and mining related processes such as loading and tramming, are now commonly used by the mining industry. An approach is presented that can aid the engineer in creating the visualizations necessary for accurate presentations for use in public relations, safety training, production projections, reclamation plans, etc. It is shown that the creation of such digital representations of mining environments are independent of the mining package used to create the original mine design. Once a proper model has been created, any view of the areas is possible. These views can be taken from any number of stationary points or entered into an animation showing the progress of a mining construction. The paper focuses on the presentation of the steps used to accomplish the visualization and an example is for a quarry fill placement project.

Jan 1, 2002

By William R. Groseclose, Kenneth D. Schoeman

The Buckskin Mountains Tunnel is a key link in the Bureau of Reclamation's Central Arizona Project. The 22-foot (6.7-m) diameter tunnel is being bored in a north-northwesterly direction through volcanic rock near Lake Havasu in western Arizona. The 6.9-mile (11-km) conveyance tunnel will carry up to 3,000 cfs (85 cu m per sec) of water through the Buckskin Mountains as part of the Granite Reef Aqueduct. The water for the project will be drawn from Lake Havasu behind Parker Dam on the Colorado River and pumped some 800 feet (244 m) above the lake to the inlet portal of the free flow tunnel where it begins its 190-mile (300-km) journey to Phoenix, Arizona, and beyond into Orme Reservoir (figure 1). Precast concrete segments are being used as a single system initial support and final lining in the tunnel being excavated by a tunnel boring machine specially designed and built for the job by The Robbins Company. J. F. Shea Company, Inc., of Walnut, California, is constructing the tunnel for the Bureau of Reclamation.

Jan 1, 1976

By Pedro Marques Bernardo, Carlos Dinis da Gama

This paper presents a methodology for design and simulation of underground ventilation networks, based on the analysis of real situations, followed by the careful interpretation of the obtained results in order to implement their optimization. The method involves two basic steps: the construction of a complete ventilation data base for the mine, upon a series of care- fully previous surveying studies in order to determine the values of its ventilation parameters, and the simulation of relevant situations for the ventilation system optimisation. A simulation model, modified after the Hardy Cross method, allows the testing of various mechanical means located at different points of the network, aiming to determine the technical-economical feasibility of each solution. These simulations obey the directions of air flow in each point of the mine, as determined by the directions of the natural ventilation flow established in the data base that represents the network. The methodology was validated upon studies developed in ventilation network of the Panasqueira Mine (Portugal), in two situations: regular production (mechanical ventilation) and care- maintenance (natural ventilation).

Jan 1, 1997

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flow schemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none of them has led to a satisfactory conclusion. A technique was developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program was constructed that makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low-grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems. Key words: Modeling and simulation, Size reduction, Mineral liberation, Taconite, Magnetic concentrator

Jan 1, 2003

By Todd Kilduff, Michael Tinney

The North Temple Tunnel pedestrian underpass in Salt Lake City, UT was built using a pipe canopy method that met significant challenges in potentially running ground conditions. Kilduff Underground Engineering (KUE) was the designer for the 20-foot-diameter SEM tunnel, Design-Build contract. Geotechnical data indicated ground conditions consisted of loose silty gravel for the majority of the face overlying soft to medium stiff clays in the tunnel invert. KUE designed a pipe canopy as pre-support to stabilize cohesionless gravels in the crown, a shotcrete initial liner with lattice girders to minimize disturbance of the finer-grained materials in the invert and a final liner with waterproofing system. The project was presented with a few unique challenges, primarily from the adverse ground conditions, but was successfully completed safely and schedule

Dec 1, 2022

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By M. V. K. Reddy

A differential flotation process for recovery of molybdenite from chalcopyrite concentrates produced at Rakha Copper Concentrator, Bihar, India has been developed. The flowsheet is simple, and relatively inexpensive and yields a concentrate assaying not less than 45% Mo at a recovery of minimum 65%, starting from chalcopyrite concentrate assaying 0.4% Mo. The consumption of the main depressant used, sodium sulphide is not more than 25 kg/t of copper concentrate processed without steaming; and with steaming the consumption was brought dorm to less than 12 kg/t of concentrate. Further reduction is possible by optimization of steaming parameters. Based on laboratory experimental results, further tests were conducted on concentrator site and process design parameters were established for design of commercial plant.

Jan 1, 1982

By K. A. Eriksson

Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind -and Secondary Mills. There are, however, only a few Primary Mills in operation with "solid" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a cost per ton basis and/or downtime for liner replacement would be too high.

Jan 1, 1988