Search Documents

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By S. Mertikas

The purpose of this paper is to set the stage for (1) the determination of the specifications and actions required for a successful development of a system for the management of waste deposits and contaminants resulting from activities in the mineral industries and landfills and (2) the appropriate infrastructure to be developed at the industrial level. The design of this system would be such that its application could be extended to other industries as well. Waste deposits and contaminants from activities in the mineral industries and landfills commonly cause damage to the environment. In addition to precautionary measures aiming to protect against environmental impact, early warning and immediate response to mining hazards and contaminants is a requirement for sustainable development. Hazard detection and control requires continuous and real-time detection techniques, as well as methods for tracing and predicting the motion of contaminants and waste products. The efficient accomplishment of these goals in the minerals industry requires developing an integrated system for environmental monitoring using remote sensing technologies, in combination with advanced image analysis and geostatistical techniques.

Jan 1, 2003

By Stephen R. Brown

Current conditions in the gold market demand that mine and plant operators make budgeted production targets at the lowest possible unit costs. For those companies bringing new gold pro­duction capacity on-line, achieving budgeted production levels as quickly as possible after start-up is vitally important to mini­mize unit costs and to begin a positive cash flow. Whether the objective is to simply improve unit costs or successfully start-up a new, complex plant, success will be strongly influenced by the skill levels of the operators and supervisors. The only way to assure return on plant investment, and to survive during depressed metal prices, is to ensure that plant operators have the knowledge to effectively run the plant. Technology available in computer-based, multimedia training systems, including: inter­active animation, videos, voice-overs, schematics, and text can now be used to train operators at their own pace using plant-spe­cific information. Additionally, it has been shown that learning through multimedia provides a higher degree of long term reten­tion than more traditional learning methods.

Jan 1, 1998

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By Thomas P. Meloy

A brittle solid broken by crushing or impact, results in a mass size distribution curve having a straight line segment when plotted on log-log paper. Depending on the mineral, the slope of this straight line segment ranges from a maximum of one for materials like glass and quartz to values of one half or less. Theoretical derivations of the size distribution, such as the Gaudin-Meloy model, yield a slope of one and only one. When the Gaudin-Meloy model is modified to assume that not all cracks terminate on a preexisting surface, the new model predicts that size distribution slopes, depending on the type of brittle solid, will be less than one. There is a measurable physical parameter that will predict the slope. In addition the model predicts that particles from such a size distributions will have negative corners and peaks - indentations. Moreover the model predicts that particle shape will systematically change with decreasing particle size. Finally, this new physical model of comminution may be experimentally tested.

Jan 1, 1995

By Lee Herold Storey

Groundwater remediation is growing in occurrence in the western United States. Groundwater remediation programs are regulated by state water quality statutes. The remedial action plans implemented under these statutes may conflict with well-established existing rights to withdraw groundwater for beneficial use. This paper discusses how the states of Arizona, Colorado and New Mexico administer conflicts between the need to withdraw and remediate groundwater with the existing rights of others to withdraw groundwater for beneficial purposes.

Jan 1, 1991

By D. H. Desy

This research was undertaken to establish the lncendivity of aluminum alloys against rusty steel under frictional impact conditions at typical coal mine fan speeds, to determine any differences in incendivity among various aluminum alloys, and to Investigate less incendive materials as substitutes for aluminum alloys. With a specially designed apparatus, three aluminum casting alloys and three constructional steels were tested for incendivity in frictional impact against rusted steel in flammable methane-air mixtures. Although varying in degree, all aluminum alloys investigated exhibited a high ignition probability under the test conditions; none of the steel specimens tested caused any ignitions under the same conditions.

Jan 1, 1973

By S. N. Groudev

A process for the combined chemico-biological removal of iron present as oxide minerals in different mineral raw materials (quartz sands, kaolins, clays, etc.) was developed. In the process, mineral raw materials are leached at about 90 °C with lixiviant containing microbially produced oxalic and hydrochloric acids. The leaching is carried out in mechanically stirred acid-resistant reactors for periods of from 1 to 6 hours, depending on the iron content and the forms of iron in the raw materials being leached. The iron contents of some sands treated by this method were lowered from levels that were in the range of 0.035% to 0.088% Fe2O3 to less than 0.012% Fe2O3, making them suitable for the preparation of high-quality glass. The iron contents of different kaolins were lowered from levels that were in the range of 0.65% to 1.49% Fe2O3 to levels in the range of 0.44% to 0.75% Fe2O3. As a result, the whiteness was increased from values of 55% to 87% to values of 86% to 92%. The iron content of clay was lowered from 6.25% Fe2O3 to 1.85% Fe2O3, and this increased the “fireproofness" of the clay from 1,670°C to 1,750°C. A similar process was used for the leaching of aluminum from aluminosilicates, mainly clays and kaolins. However, in this case, the microbial fermentation fluid containing citric acid was acidified by means of sulfuric or hydrochloric acid or by means of different mixtures of mineral acids. For enhancing aluminum solubilization, the aluminosilicates were heated before leaching at 600° to 650°C for 1 to 2 hours. Over 90% of the aluminum present in different clays and kaolins were leached within 3 to 6 hours. "Silicate " bacteria related to the species Bacillus circulans were used to leach silicon from low-grade bauxite ores containing aluminosilicates as impurities. The bacterial action was connected with the degradation of the mineral structures (by means of microbial metabolites such as organic acids and exopolysaccharides), as well as with the selective separation of the rich-in-aluminum fine fractions, which were retained by the mucilaginous capsules of the bacteria. The solid residues after treatment were characterized by higher values of alumina and silicon module (A1203: SiO2 ratio), and they were suitable for processing by means of the Bayer process for recovering aluminum. The bending strength and other ceramic properties of kaolins were improved by contact with well-developed cultures of "silicate" bacteria. The improvement was caused mainly by bacterial metabolites (exopolysaccharides) that acted as resins during drying.

Jan 1, 2000

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By Patrick M. James

Many in mining believe that the industry is slipping behind in public image, in public mineral education and, particularly, in mining's basic right to do business. It is critical to turn things around - to change the rules of the game soon - before mining loses any chance of recovery. In the industry's experience, there is a technique of project development and operation that can help gain ground on public opinion. Only recently has this technique had a name, and that is sustainable development. What is sustainable development? Sustainable development is broadly accepted and supported by the international business community. And significant thought and work has been devoted to the subject. Research into the topic was initially confusing because the definitions of sustainable development are written in terms the writer, and his or her constituency understands. To some, it refers to environmental protection. To others, it is about social responsibility. And to the developer, it is about economic benefit. Slowly a theme emerged from the research that seemed to be part of all the definitions. That theme has three parts. First, the development, whatever or wherever it is, must contribute economic value to the developer and the stakeholders of the development. Stakeholders in this context include employees, neighbors, residents of the surrounding area, citizens of the country, suppliers and all others affected by the development. Next, sustainable development must contribute environmental value. This means that at a very minimum it must be neutral and not cause irreparable damage. And last, and what is new for miners and most other businessmen, it must contribute real social value to the stakeholders. How to use the concept? With that three-part theme as a working definition, the mining industry must find ways to use that “the challenge is for an individual company to translate what sustainable development means for them. There is no one model..." Donald W. Gentry is president and chief executive officer of Polymet Mining and former professor emeritus of mining engineering at Colorado School of Mines. He added: "While simple to state, the concept is anything but simple to implement. Present trends indicate ... one wins the sustainable development argument by staking out the high ground early..." In other words, start using sustainable development principles at the beginning of the project. New ways of doing business The mining industry's challenge is to implement sus¬tainable development universally around the world. Paternalism as a way of doing business is dead and a new model of doing business is emerging. All types of businesses are learning to deal with the stakeholders of new developments. Mining cannot be an exception to these trends. To understand how the international mining business came to sustainable development, it is useful to look back a few years. For many North American mining engineers, there were few opportunities for foreign assignments from the 1960s to the 1980s. American companies had been asked to leave many of the Latin American countries. Africa was going through a continent-wide upheaval. The Soviet Union and China had Eastern Eu-

Jan 1, 2000

By S. B. Kim, J. Hong, K. Park, W. Kim, H. Kim, Y. Han, J. Choi

"For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50–200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.INTRODUCTION A great number of potential applications of lithium are being developed currently by the thermonuclear fusion power generation industry(1,2) as well as by the battery and fuel cell industry(3). Even though lithium is mainly consumed in the form of lithium metal and some lithium compounds, about 10% of total lithium production is consumed directly as mineral concentrates by the ceramic industry for the manufacture of special ceramics and mica based glass-ceramics(4). Granitic pegmatites normally contain feldspars, quartz, and mica in addition to lithium-bearing minerals such as spodumene (LiAl(SiO3)2), petalite (LiAlSi4O10), and lepidolite (KLi2Al(Al,Si)3O10(F,OH)2). The amount and grade of metallic minerals tend to gradually decrease and become lower, leading to the increase in the price of base metal or metallic compound(5). Accordingly, recent studies have been extensively devoted to developing the technique to improve the grade of metallic minerals from low grade metallic ores(6,7). Nevertheless, studies regarding the improvement of Li grade from lepidolite ores are very scarce. Lepidolite is a phyllosilicate mineral of the mica group and is often associated with other minerals such as calcite, muscovite, feldspar, and quartz, which need to be separated for lepidolite enrichment(8). Many studies have reported the flotation techniques for separating calcite, muscovite, feldspar, and/or quartz from various targeting minerals(9-11); however, there has been no attempt to investigate physico-chemical properties of lepidolite and its separation from such types of gangue minerals through flotation. Hence, in this study, for the first time, flotation has been carried out for the quaternary ammonium salts (stearyl trimethyl ammonium chloride (STAC, (CH3)3CH3(CH2)16NCl))-lepidolite system based on only the electrokinetic property of minerals that consist of lepidolite ores without adding any depressant to get an initial insight on its flotation behavior. The experimental variables that influence the lepidolite flotation such as amount of collectors, feed size and solution pH have been also examined."

Jan 1, 2015

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

By D. R. Nagaraj

The chemistry and structure-activity relationships for four new classes of sulfide mineral and precious metals collectors developed recently are discussed in this paper. These collector classes are alkoxycarbonyl alkyl thionocarbamates and thioureas, dialkyl (or diaryl) monothiophosphates and dialkyl monothiophosphinates. The main emphasis will be to highlight the differences between collectors and their affinities for various minerals on the basis of data on kinetics of adsorption on pure minerals, natural ore flotation and microscopy of flotation concentrates. The mechanism of interaction of these collectors with sulfide minerals is also discussed with the available data on the FTIR and solution chemistry studies.

Jan 1, 1989

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By H. H. Murray

New and improved benefication techniques are available to allow the production of clay minerals of exceptionally high purity. This is particularly true for kaolins and smectites. Wet processing techniques including particle size separation, high intensity magnetic separation, chemical leaching, flotation, and selective flocculation are described and results and applications are discussed. The blending of clay minerals with other minerals provide opportunites to make special ceramic materials such as cordierite and other minerals which have very special ceramic properties including low heat expansion, high fired strength, low absorption, and other desired qualities.

Jan 1, 1989

By O. Ozcan, J. D. Miller, Z. S. Nickolov

The production of soda ash from trona (sodium sesquicarbonate, Na2CO3•NaHCO3•2H2O) resources has completely displaced the production of synthetic soda ash in the USA. Further, the utilization of other trona resources is under consideration in China, Turkey, etc. Recent research has been concerned with the development of flotation technology for the trona industry. In this regard studies on the flotation behavior of sodium carbonate salts: trona, sodium carbonate monohydrate and decahydrate, as well as the flotation behavior of sodium bicarbonate, are reported for both cationic (dodecyl ammonium hydrochloride) and anionic (sodium dodecyl sulfate) collectors. It has been found that strong flotation of sodium bicarbonate (NaHCO3) can be achieved with 100% recovery, while the other sodium carbonate salts do not float well. These results have been explained by FTIR analysis of aqueous solutions of Na2CO3and NaHCO3in a range of concentrations from very dilute to saturated conditions. The changes in the shape of the O-H stretching band of water are correlated with the flotation behavior of Na2CO3salts and NaHCO3. In addition, the absorption band of the carbonate ion at ca. 1385 cm-1is used to monitor its interactions with water and/or other ions in solution. The infrared results demonstrate thatNa2CO3acts as a water structure maker, leading to an extensively hydrated surface that accounts for the poor flotation of most sodium carbonate salts. In contrast, NaHCO3does not have this characteristic and consequently complete flotation is possible with both cationic and anionic collectors. These results support the previous water structure analysis for soluble salt flotation of alkali halides and other oxyanion salts.

Jan 1, 2003