Search Documents

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) is used in the mining industry for early fire detection. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) have developed a direct method to calculate the fire heat release rate (HRR) when a mine fire is close to the AMS sensors, but this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire HRR using AMS sensor data at any location downstream of the fire. The method was validated using a full-scale diesel fire test conducted in the Safety Research Coal Mine at NIOSH’s Pittsburgh Mining Research Division.

By Michael H. Leon, John A. Organiscak

Controlling worker dust exposure on longwall mining systems is difficult because the working face area serves as an immediate return during the mining cycle and the amount of airborne dust generated is directly related to production. Since improvements in longwall mining technology have significantly boosted production levels, additional technology is needed to control the airborne respirable dust generated at present and future production levels. One concept to reduce longwall worker's dust exposure is to maintain two splits of air at the face -- a clean intake split in the workers walkway, and a return (dusty) split over the face conveyor. The U. S. Bureau of Mines has recently investigated a concept to overcome the visibility handicap of face partitions by utilizing a permeable polyester mesh. The mesh material was anticipated to provide adequate air-splitting capabilities as long as the pressure differential between the face and worker walkway was minimal. Initial testing of this concept at the Bureau's Lake Lynn Laboratory showed that notable reductions could be achieved with a 1/8 in (3.18 mm) and 1/16 in (1.59 mm) mesh opening size. Dust reductions at 100 ft (30.5 m) and 200 ft (61.0 m) downstream of source were 58 and 36 pct, respectively, for the 1/8 in mesh and 79 and 55 pct, respectively for the 1/16 in mesh. Longwall application of the 1/8 in mesh showed similar results to the Lake Lynn Laboratory tests. A flame retardant mesh was used underground with portable lighting mounted on the shearing machine for face side lighting.

Jan 1, 1993

By W. M. Jr. Aubrey, R. L. Stone

INTRODUCTION Most metallic minerals and some industrial minerals have a relatively high specific gravity and most have at one time or another been concentrated by gravity methods. The principles of gravity concentration are straightforward, well documented and easy to understand, but in practice there are many pitfalls that await the engineer in the development of an integrated flowsheet. Gravity concentration equipment has a long history of use and there is a great diversity available. The equipment is capable of treating material over a broad size range, only falling off in efficiency in the very fine sizes. Gravity concentration is also inexpensive, generally free of environmental problems, and commercial equipment can process large tonnages of ore with a minimum of capital cost. As might be expected of an efficient and low cost process, the bulk of the tonnage quickly and inexpensively. Another obvious application is treating mineral deposits such as hematite and manganese ores that are sufficiently liberated after a minimum of crushing to allow production of a coarse concentrate that will meet market specifications. Except for hand picking and mechanical sorting, there is no competing process on coarse size material. Conversely, it is sometimes obvious that gravity concentration does not warrant consideration. Examples are ores that require very fine grinding to attain liberation, for ores where the minerals of interest have a gravity similar to the gangue, and ores that are strongly magnetic. Actually a mineral processing engineer may not know if gravity is the best way to concentrate an ore, but he should have little difficulty recognizing when gravity concentration deserves consideration based upon specific gravity differences and liberation gravity concentration has wide use. size. His challenge then is to At times its selection as the identify and test the applicable primary concentration process is processes, to develop a obvious. Low grade placer deposits metallurgical balance and flowsheet of tin, gold and beach sands usually for the best process, to estimate are only profitable because gravity production rate over the life of concentration is able to throw away the deposit and to make equipment

Jan 1, 1986

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By M. N. Brodie

The paper examines the requirements for electric power used in concentration and dewatering circuits, the effects of plant capacity and process type, the restraints imposed by the primary supply and applicable codes and outlines the procedure by which effective design is carried out.

Jan 1, 1986

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By Sean E. Armstrong, Deepak Malhotra

Gold extraction from refractory ores as a percentage of total gold production is increasing. The processing technology options for treating difficult-to-process refractory ores are also increasing. The best processing option is dependent on many factors including feed grade and the cause for ore refractoriness. The causes for ore refractoriness are many foldCpreg-rob­bing, encapsulation in pyrite, arsenopyrite or silica, presence of cyanocides, presence of cyanide-insoluble gold compounds, etc.1. The first step in the process development of a refractory gold deposit is to determine the cause for ore refractoriness. The traditional approach of undertaking detailed mineralogical examination of ore types, major and minor mineral constituents and their association does not necessarily provide the metallur­gist all the information needed for characterization of gold-bear­ing ores. For process development programs it is desirable to complement traditional mineralogical methods with diagnostic leach testing, which attempts to quantify the deportation of gold in various mineral matrices. This paper briefly reviews the diagnostic leaching proce­dures and its applications for a wide range of gold-bearing refractory ores, both primary and by-product.

Jan 1, 1996

By S. S. Nadgauda, A. J. Hathaway

Typically, as long as the coal quality is within the specified range, electric utilities have used delivered cost of fuel per million Btu as the primary criteria for qualified coals when making coal-procurement decisions. Such an approach may not fully address the total cost of using different quality coals at a given plant. A practical and easy-to-build model is described for estimating plant-specific utilization costs for coals of different qualities. Examples are included to illustrate the modeling results for plants operated by two utilities. While the model has certain limitations, it does represent an improved method for evaluating coal bids, and, consequently, reducing generation costs.

Jan 1, 1990

By Charles D. Litton

This report describes a smoke particle detector which utilizes a novel three electrode configuration and 5.0 [] source of Americium 241. The detector operates on the principle of diffusional charging by a region of unipolar molecular ions. The detector is sensitive to particle concentrations in the range of 10 to 5 20 ug/m3. The detector is intended for use primarily as an early warning fire detector but has the potential for other applications of particulate monitoring. In particular, this report adresses the potential use of the detector for monitoring diesel particulate matter (DPM). To assess the viability of this application, particle size data obtained from in-mine sampling of both DPM and dust were used to derive detector sensitivity functions for DPM and dust as a function of their mass concentrations only. These sensitivity functions are dependent upon the average diameters and size distributions of the DPM and dust. Using the derived sensitivity function for DPM, experiments were conducted in a ventilated tunnel where the true DPM mass concentrations, measured using a Tapered Element Oscillating Microbalance (TEOM) were compared to the mass concentrations calculated using the detector sensitivity function. The agreement between the two measurements was good, indicating that with additional experiments, coupled with in-mine evaluation of the detector, refinement of the device for use as a continuous monitor for DPM appears feasible.

Jan 1, 1989

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By F. W. DeVries

The preoccupation with cyanide as an environmental issue has been described as virtually an obsession for state and federal agencies enacting regulations for environmental protection. This seems likely to continue in legislative planning, as well. This is despite the fact that the only significant group of cyanide-related incidents has been the bird-mortality occurrences, predominantly in arid areas, and these have been greatly reduced by a concerted effort by operators. What follows is a brief list of areas for which the industry may need either additional information or plans for defensive strategies over the next two to five years.

Jan 1, 1991

By John M. Anderson

This paper examines the methods available to improve climatic conditions around a deep, high production longwall district of a British coal mine using results from a computer model. Such methods include the provision of increased ventilation quantities, the application of refrigeration, the reduction of heat input at source and the use of alternative ventilation systems. An approach to the solution of a climatic problem is explained with reference to other coal mine contaminants and a cooling strategy for deep high production British coal mines is described.

Jan 1, 1987

By Jerome C. Neyer

Within most of Canada and the northern third of the United States, the soils overlying bedrock are of glacial origin. Tunnelling in glacial soils presents numerous challenges to the contractor, including abrupt changes in soil type, boulders and glacial erratics, water bearing fine sands and silts, toxic or explosive gases, and glacial till. This paper examines the available techniques for geotechnical exploration in glacial soils; the relationship between subsurface conditions predicted by various techniques and conditions actually encountered during tunnel construction; and potential improvements in the planning and implementation of geotechnical explorations. Case histories of geotechnical exploration and tunnel construction in glacial soils are also reviewed.

Jan 1, 1985

By Janusz Szywacz, Bozena Bojko, Stanislaw Wasilewski

Two groups of computer programs are described in the paper. First one is the OWEN system containing software modules designed for air flow distribution analysis and prediction within the whole ventilation network of a mine. The second group is a set of programs commonly used in a routine design work connected with chosing the optimal ventilation schemes and equipment for individual areas of a mine (headings. longwall districts etc). All the programs are designed for running on the IBM PC/XT, IBM PC/AT and compatible computer systems.

Jan 1, 1989

By W. D. Monaghan, A. J. Kwitowski, A. L. Brautigam

Teleoperation is a technology that can provide significant health and safety improvements in mining operations by locating machine operators hundreds of meters away from the face area. The US Bureau of Mines recently developed a teleoperation system for continuous mining and haulage equipment. This system features near real-time closed-loop control. A prototype system was developed and demonstrated. This system could be used in thin-seam applications down to 36 in (914 mm). Provided are details of the teleoperation system, the results of testing and the expected applications of this technology.

Jan 1, 1996

By Chuck Hornaday, Brad Miller

Geosynthetic clay liners (GCLs) are manufactured barrier layers containing a high-quality sodium bentonite clay attached or adhered to geotextiles or a geomembrane. The GCL's low permeability and high strength make it an ideal replacement for low permeability soil or clay liners for mineral extraction and processing containment applications. This paper will discuss the advantages of utilizing a GCL versus compacted clay in containment applications. Some of the advantages include: the GCL's lower permeability (5 x 10-9 centimeters per second (cm/sec)) and corresponding better composite liner leakage protection, the GCL' s greater resistance to desiccation, differential subsidence and freeze­thaw, and lastly, the ease and speed of installing the GCL. This paper will also detail a number of important case studies related to the mineral extraction and processing industry. These case studies include using GCL in two large reclamation capping projects, as a secondary liner in two gold heap leach pads, as a composite liner in a dam for stormwater runoff control, and lastly, as a primary liner for a tailings runoff diversion channel.

Jan 1, 1997

By C. N. Greene

I am sure it is obvious to all of you that a complete program of casualty and property insurance is as necessary for any tunneling contractor as it is for anyone else involved in trade in the United States today. Going beyond those general undefined terms, there are many areas that need specific attention, particularly for contractors, regardless of size. WORKERS' COMPENSATION Workers' Compensation is mandatory in all states and the District of Columbia. In most of the states, private insurance provides this coverage. In a few states, the state operates Workers' Compensation funds, some of which are competitive with the private sector and others are operated on a monopolistic basis. Under a monopolistic setup, you have no choice, you must buy coverage from the state. Self insurance of the Workers' Compensation risk is also an alternative in most jurisdictions. With a contractor operating only in the U.S., the coverage extensions are few in number. If your work brings you anywhere near navigable waterways or land extensions thereof, you should have both U. S. Longshoreman and Harborworkers' coverage, as well as Employer's Liability coverage for the master or members of the crew of a vessel.

Jan 1, 1983

By Hans von Michaelis

This paper examines the process options available for treatment of "refractory" gold ores. As more and more of the easily leached oxidized gold ore zones are exhausted, the pressure is on to find more economical ways of treating refractory gold ore deposits. Historically, refractory ores were generally concentrated, e.g. to make a flotation concentrate that could be roasted. A major development is taking place in the USA in which ores from which gold cannot be concentrated well by flotation are being treated using whole ore oxidation processes prior to cyanidation. Refractory gold ore treatment processes are generally expensive to install and operate. Thus, for a refractory gold ore project to be economically viable, the grade must generally be higher than for free milling gold ores.

Jan 1, 1993

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986