Search Documents

By W. C. Shanks

Metalliferous sediments and/or saline brines have now been discovered in numerous sea floor deeps along 900 km of the axial rift zone of the Red Sea (Fig. 1). The Atlantis II Deep remains the most interesting of the the brine deeps both in terms of intensity of submarine hydrothermal processes and in terms of potential economic importance. In fact, successful completion of a pre-pilot mining test in 1979 indicates that the Atlantis II Deep may become the first deep sea base metal sulfide mine (Mustafa and Amann, 1980). Under the most optimistic scenario, the Atlantis II Mine might be established 4-6 years after completion of a year long pilot mining test in 1983-84. If established, mining would produce about 100,000 tons per day of wet mud with about 200 tons per day contained zinc, and proportional amounts of Cu and Ag. Expected mine life would be about 15-20 years (Anon., 1981). In addition to direct economic importance, the Red Sea brines and metalliferous deposits provide significant insight into exploration for sea floor brine-related ore deposits and for analogous ancient deposits. In this paper I will concentrate on the economic potential of Red Sea deposits and sea floor exploration for brine related deposits, but some ramifications of relevance to ancient deposits are extant.

Jan 1, 1982

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By J. W. Mustard

The Macmillan Pass tungsten property (MacTung) is the largest known copper-tungsten, calcic, exoskarn deposit in the Western Hemisphere. Located on the border between the Yukon and Northwest Territories in northwestern Canada, the deposit crops out on Mt. Allen within the Selwyn Mountain Range. It was discovered in 1962 by a subsidiary of AMAX Inc. and has since been explored by 16,300 meters of surface and underground diamond drilling and by 800 meters of underground development. Geologic reserves are in excess of 30 million tons, grading slightly less than 1.0% WO3. Scheelite (CaWO3 ) is the main mineral of economic interest. Accessible by road, the property is not in production. Previously estimated reserves at MacTung have been unable to fully utilize all the geological controls on mineralization. In the past three years, however, an intensive program has been underway to improve our understanding of the deposit and to use the resulting information in a more precise way. This paper will discuss the key aspects of the geology as they specifically relate to reserve estimation and will demonstrate how these controls are being used in a geostatistical model of the deposit.

Jan 1, 1985

By J. M. Applegate

In the same way that a blueprint communicates information about a structure, a useful systems architecture should provide information that guides the construction and implementation of computing systems. Taking the blueprint analogy a step further, a plot plan can also show where in the "bigger picture" a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: 1. The primary purpose of computer based systems relative to particular task or operation. 2. The relationship of systems to each other and an indication of their interaction and dependencies. 3. The relationship of systems relative to the organization and its objectives. 4. Indications of where IS/IT resources can best be allocated to support the organization. 5. The overall context in which new systems and technologies can be assessed for both their impact on current system and on the organization itself.

Jan 1, 1998

By T. M. Barczak, Zach Agioutantis

The Support Technology Optimization Program (STOP) has been developed by the National Institute of Occupational Safety and Health (NIOSH) to provide a comprehensive tool for evaluating the performance of available secondary roof support systems and designs based on support strength, convergence, cost, installation time and material handling considerations. This program uses engineering models developed from full-scale testing of numerous supports under controlled loading conditions in the unique NIOSH Mine Roof Simulator load frame to determine the support load-displacement performance as a function of the various sup- port design parameters. Both standing supports, such as wood cribs installed within the entry, and intrinsic supports such as cable bolts, can be evaluated. Support systems can be designed and compared for use in a new mining section or to evaluate potential replacements for an existing design. The support design requirements are defined from 1) estimating the failure height in the immediate roof, 2) in-mine measure- ments of support and strata interaction or development of ground reaction curves from numerical modeling, 3) the performance of an existing support system, or 4) from any arbitrary load and convergence criteria. All settings can be saved to permit resuming an evaluation in progress at a later time. This paper presents the updated MS Windows version of this tool, which can be easily installed and run on a personal computer. This Windows implementation will feature a project and application scenario setup where multiple scenarios can be assigned to one project. Scenarios can then be compared on support parameters and cost. Cost parameters can be provided either as individual cost items or using a price grouping feature. Additional support performance curves and/or additional ground reaction curves will be distributed with program updates as new information is developed. Users can also provide their own support and/or ground reaction curves.

Jun 25, 2024

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: 1) investigate the utilization of sandy kaolinS and other clays associated with bauxite-kaolin deposits; 2) find limits of the bauxite district, looking for possible extensions; and 3) study the geology of the district, looking for patterns or trends that may aid in finding new ore reserves. This work was done with the full cooperation of mining companies operating in the district and property owners. Research was aided by the U.S. Bureau of Mines and the University of Alabama. The investigation included detailed geologic mapping of mines, drilling in selected areas, and making mineral analyses of bauxite and clays. The mapping was performed primarily by pace and compass because of the complexity of the deposits studied, but aerial photographs were used to a limited extent. Drilling included both auger and core drilling. The auger drilling was limited to 100 feet, but core holes were drilled as deep as 200 feet. The term 'bauxite,' as used here, indicates a mixture of minerals containing more than 50 percent gibbsite. Bauxitic clay is a mixture of gibbsite and kaolinite that contains more kaolinite than gibbsite. The term "kaolin" indicates a clay composed of predominantly kaolinite. Other clays in the Eufaula district are composed of kaolinite, illite, quartz, mica, and goethite or hematite.

Jan 1, 1971

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

By Alvin D. Cronberg

Silica flotation with amine salts has been a commercial process for years in certain non-sulfide mineral systems. Phosphate rock and feldspar deposits are notable examples. Generally, the quartz is clean and coarse. Primary amines and imidazolines are used, usually in a mole weight range 250-300, ad often fairly impure grades of collectors are satisfactory. As the production of magnetic iron concentrates grew in Michigan, Minnesota, Canada and in foreign locations, the iron mining companies began to explore amine flotation of silica to improve these concentrates. Many of the mining companies, as well as reagent suppliers, government laboratories and university research teams, had already studied amine collectors for silica, but the application to magnetic iron concentrates presented a real commercial opportunity to apply the art. Amine flotation of silica has been accomplished by simple addition of a flotation cell, and possibly a regrind mill, at the end of the magnetic concentration process. The flotation system gave the mill operator a flexible method to control final grade caused by ore variations in the feed. It increased iron content with lower silica, which resulted in lower freight costs per unit Fe and better pellets for blast furnace use.

Jan 1, 1968

By R. H. King

Recently, the North American mining industry experienced a severe recession, forcing managers to take dramatic steps to cut costs and compete in the difficult international market. Some of these steps were closing mines, reducing work forces, renegotiating wage agreements, and purchasing the most productive equipment. Managers are now looking beyond these traditional avenues and are focusing more on advanced technology. In the present environment, it is essential that mine operators obtain the maximum use of capital expended on equipment. However, mine workers do not obtain maximum efficiency or productivity from equipment because the adverse and hazardous mine environment impedes human performance. Also, the efficient use of large, complex machines calls for levels of precision that many times are beyond the capability of even highly trained miners. A possible solution to this problem is a machine that mines without operators - autonomous mining machines. However, numerous problems confront researchers who are attempting to develop such equipment. Some mining tasks are not always composed of a series of cyclic motions readily performed by factory floor robots. In addition, mining takes place in the geological environment where conditions are highly variable and unpredictable. As a result, these machines must be able to sense and adapt to variations in operating tasks and environment. Considerable autonomous vehicle research has been completed, especially for defense. However, autonomous vehicle (AV) technology has not advanced to practical application yet (King, 1988) and mining research is necessary in areas: representing mining specific knowledge; •analyzing and reasoning about sensor data in the mining environment; and •discovering completely new mining methods or new approaches to existing methods that become apparent when we remove the constraints imposed by the necessity of human operators. A specific machine, the LHD, can be used to show the problems for researchers who are attempting to develop autonomous machines for mining. This author chose the LHD because it can borrow concepts developed for autonomous navigation by military programs. But considerable mining research is also required. Furthermore, studies done at the Henderson mine, in Colorado, show autonomous LHD 's promise cost and safety benefits (King, 1988). At Henderson, LHDs load ore from draw points, tram to an ore pass, dump and return, or switch to another draw point. An autonomous LHD must sense vehicle position along the route, relate sensor data to stored-map information, to determine location, follow drift center lines, plan paths between dump position and initiate appropriate control commands, sense vehicle operating status and vehicle health, key on features or targets for special tasks like high speed turns, perform end of travel tasks (loading and dumping), and detect and avoid obstacles. These goals are similar to those for shuttle cars, trucks, and front-end loaders. Therefore, much of the technology is transferable. Each Henderson LHD extracts six to 40 dippers from each of a series of draw points. The LHD transports the ore to an ore pass within 55 m (180 ft) of the draw point, making the longest round trip 110 m (360 ft). The LHDs have very fast hydraulic dumping and loading systems that reduce the round trip cycle to less than one minute. Even though the LHD is capable of 500 trips per shift, the average production is 300 dippers. Man trip and lunch reduce available operating time to 6.5 hours per shift. Mucking difficulties (setting large boulders aside), operator breaks for activities like talking shop, and cleaning and smoothing roads further reduce operating time. Supervised autonomy can reduce the number of operating units by increasing operating time per shift since computer controlled machines can operate during lunch and between shifts and reduce operator errors. If dippers per shift increase from 300 to 350 (long-range goals are 500 dippers per shift), constant production requires only 10 operating LHDs and two spares. Manpower requirements drop from 24 to four by controlling five machines from one workstation. A review of technology available from the Autonomous Land Vehicle, the Advanced Ground Vehicle Technology, the Ground Surveillance Robot, and other programs, show the following differences between others work and mining industry needs: •If we focus initially on mobile haulage vehicles, we can navigate from a map. We do not need to explore. •We can modify the environment to reduce the navigation requirements. •We have a harsher environment than any of the research programs have encountered. •Our equipment must operate faster and more precisely than present AVs. •Our equipment must operate reliably over long periods of time. •We must have better onboard machine health monitoring and diagnostics. •The AV programs do not address geosensing. •The major AV programs are not cost-effective. For example, we cannot afford the computer power for robust image processing, yet. To computer control an LHD, we must replace the guidance and monitoring skills of experienced operators with sensors, computing hardware, interfaces, and several software mod¬ules. Experienced operators avoid collisions and load efficiently in piles that may contain oversize muck. Collision avoidance without an operator requires sensing all obstacles in the draw

Jan 1, 1991

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958

By Peter I. Brooker

The semi-variogram, the basic tool of geostatistical estimation procedures, must itself be estimated from the available data. From a numerically simulated two dimensional deposit, with known variability expressed through its semi-variogram, the standard arithmetic mean estimator is used to calculate experimental semi-variograms. These are determined on a series of data sets obtained from the deposit with various sampling grids which cover different areas of the deposit and which have a wide range of available data. The orders of discrepancies between estimated and theoretical semi-variograms are determined in this idealized situation; and this provides a basis against which to assess experimental semi- variograms made on field data.

Jan 1, 1982

By A. M. Marabini, V. Alesse, Belardi. G.

An alternative flowsheet was designed for the flotation treatment of a complex sulfide ore from the Sotiel Mine in Spain. The ore contains 0.71% Cu, 2.24% Pb and 5.63% Zn. Two specially developed synthetic collectors, methyl-mercapto-benzoxazole (MMBO) and 6n-propoxy-mercapto-benzo-thiazole (PMBT), were examined. MMBO exerts a specific action on copper and zinc minerals after treatment with copper sulfate, and PMBT exerts a specific action on Pb minerals. Flotation operating variables (pH, frother type, frother quantity and feed particle size) were examined by means of rougher flotation tests to determine the optimum conditions for the new collectors. Once the optimum conditions were determined, a series of open flotation circuits were run on feeds of various particle sizes (obtained by different types of grinding). The objective was to obtain high-grade Cu and Zn concentrates. The results of the open-circuit tests demonstrated that a Cu concentrate grading from 18% to 23% Cu and a Zn concentrate grading from 40% to 48% Zn can be produced.

Jan 1, 1996

By N. S. Dalal, Xianglin Shi

Metal ions, such as chromium (Cr) and vanadium (V) are found as trace impurities in mineral dust. Since metal ion mediated free radical generation has been implicated in many disease processes, we carried out a detailed investigation of the metabolism of these metal ions by biological redox systems and the possible oxygenated radical generation therefrom. We found that highly reactive Cr(5+) species are generated in the reduction of Cr(6+) by NADPH-dependent glutathione reductase, lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase. The reduced metal ion species react with hydrogen peroxide, to generate hydroxyl (•OH) radicals in a continuous cycle. The enzymatic catalysis processes also involves the reduction of molecular oxygen to the superoxide [(0-1 2)] radical. Thus only a trace amount of metal ions chemisorbed on mineral dusts, such as quartz, can catalyze the generation of the highly toxic oxygenated radical species from cellular hydrogen peroxide, suggesting a new biochemical mechanism for mineral dust induced chronic lung injury.

Jan 1, 1991

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By Edward L. Vickers

When I was originally asked to give this talk, I had certain preconceived ideas of the mining industry's reaction to Operations Research. It seemed at the time to be a rather simple task to collect these ideas for presentation here today. Jotting down these notions, I became concerned that overexposure to this activity called OR perhaps had clouded my outlook on what was actually being done on a nation-wide scale. I felt, to have a better cross section, a questionnaire of current industrial activity was in order. I solicited the response of some 75 mining companies varying in sizes and operating characteristics, and I am pleased to report that the response was good. I received answers from 51. The questionnaire was intended to measure the degree to which their concerns were actually engaged in OR efforts. With all due respect to the people who were so gracious as to answer the questionnaire, I feel that there is a tremendous misconception as to the designed purpose of OR. This is not to imply that there are no active OR groups in the mining industry. But by in large, the majority of the companies sampled appear to be somewhat confused as to what OR really is.

Jan 1, 1962

By Martino Scialpi, Miriam Piemontese, Claudio Cimiotti, Matt Kendall, Nicholas Karlin, Roberto Schuerch

The Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to the White Point Manifold. Upon completion, through ground conditions ranging from soils to hard rock, the tunnel will be approx. 7 miles (11 km) long with a finished internal diameter of 18-ft (5.5 m). This paper will present the Tunneling Condition Assessment Report (TCAR) and Tunnel Operation Plan (TOP) developed prior to construction, as well as the actual TBM performances achieved along the northern portion of the alignment in soft ground, shallow cover, and beneath a densely urbanized area.

Jun 23, 2024

By G. L. Alston

The mine disaster last November in northern West Virginia has compelled the coal mining industry to take a closer look at the methods of transporting and applying rockdust. The USBM has indicated they would like to see a minimum of 80% incombustble in the back entries and want rockdust to be maintained to within 40 feet of the face at all times. With today's high rate of advance of mining machines it will be necessary to apply dust in the immediate returns continuously and the working places mutt have dust applied during the operating shift. The inspectors have become more demanding in requiring clean-up of coal and coal dust in the working place before rockdust is applied and are insisting on better clean-up and better rockdust applications along belt conveyors. Maintaining a constant application of rockdust in the back entries can be done with a Trickle-Duster. The machine is designed with hopper capacities of either 400 or 1,000 pounds of dust. The discharge rate of dust being fed through 1-1/2 inch diameter hose can be adjusted from 1/2 to 5 pounds per minute. The hose is extended into the return through the last open breakthrough and the return air carries the rockdust along w th the coal dust, depositing them uniformly on rib, roof and bottom.

Jan 1, 1969