Search Documents

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

By Thomas E. Ban

The continuous sintering process was invented more than 60 years ago by two metallurgists, Arthur S. Dwight and Richard L. Lloyd, who saw a need for automation in mineral processing. Their specific objective was to beneficiate copper ore by desulfurizing and agglomerating it for copper blast furnace smelting at the Cananea plant in Mexico1. Since their early development the process expanded widely in scope, size, and application. The current worldwide sintering applications exceed 250 million tons per year for agglomerating ores of lead, manganese, zinc, and iron. Sintering is also widely used for production of sintered lightweight aggregate from clays, shales, and fly ash. The continuous sintering process took on wide expansion during the 1960's in foreign countries. Plants for production of approximately 135 million tons per year were built in these countries for sintering iron ore fines as shipped from new iron ore projects of Canada, Liberia, India, Brazil, and Australia. This expansion represented construction of approximately 80 new sintering plants, some as large as 15 thousand tons per day production on a single large sintering machine. Sized self-fluxing or highly fluxed sinter has become recognized as a premium blast furnace charge and has enabled blast furnaces of Japan and Europe to produce upwards of 10,000 tons of metal per day with coke rates less than 1,000 pounds per ton of metal. This coke requirement is practically 50 percent of the ordinary rates achieved during the early 1950's when the peak blast furnace production was less than 113 of the current records.

Jan 1, 1975

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-growing push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source of rare earths found in the United States is bastnaesite, a rare-earth-bearing fluorocarbonate, mined at the Mountain Pass Mine in California. To increase production, it has been essential to optimize existing processes and create new ones to capture current reserves. This paper presents the results of a research program conducted to expand the understanding of the bastnaesite leaching system. With the help of prior knowledge and thermodynamic calculations, a novel single-stage hydrochloric acid leach system was created to optimize the extraction of rare earths from bastnaesite. Historically, this extraction has entailed the use of a two-stage leach system involving a high-temperature hydrochloric acid leach followed by a caustic crack. We ran a series of single-stage leach experiments by reacting locked-cycle flotation concentrate with hydrochloric acid to test common leaching parameters. The results of these single-stage tests showed significantly higher rare-earth recoveries than the reported recoveries of the historic two-stage caustic crack processes, all while decreasing the number and amount of reagents needed.

Feb 1, 2023

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand and gravel mine sites throughout the United States. These interviews verified that the competencies included in the hazard recognition competencies framework agree with perceptions of the interviewed H&S professionals, who also provided validity for the critical role these competencies play. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

By Richard Switalski, Thomas Scotese, James Morrison, Randall Essex

OVERVIEW Like many older metropolitan areas across the U.S., the Greater Cleveland area is served by a combination of separate sanitary sewers and combined sanitary-stormwater sewers. In 1966, a Master Plan was implemented by the Northeast Ohio Regional Sewer District (District) to minimize pollutant overflows into adjoining Lake Erie and its tributary rivers and streams, that would occur during wet weather events. One component of the Master Plan was to reduce the load on combined sewers by constructing new conveyances to intercept separate sanitary flows and convey them to upgraded regional waste water treatment plants for priority treatment. As part of a 15-year program to construct 74 km (46 miles) of new interceptors, the West Leg Interceptor (WLI) Project intercepts flows from four decommissioned waste water treatment plants (WWTPs), and conveys those flows to the new Southwest Interceptor (SWI), which conveys the flows to the Southerly Treatment Plant, a tertiary level treatment facility. The WLI Project was built in sections to permit decommissioning of the WWTPs as each segment of the interceptor system was completed and put into service. Flows from the first of the four WWTPs was converted to the WLI in November, 1992; the final connection was achieved in July 1994. The WLI comprises 9.1 km (5.7 miles) of 21 to 29 m (70 to 95 ft) deep mainline interceptor tunnel, four vortex drop structures, approximately 2 km (1.3 miles) of shallow tunneled connector sewer to the mainline, approximately 2.9 km (1.8 miles) of open cut connector sewers, five construction work shafts (not including one work shaft constructed under SWI Contract 6 at the north end of the WLI), and 15 access shafts.

Jan 1, 1995

By John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau of Mines philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry's needs. The Bureau of Nines programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine comnications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved nine communications systems.

Jan 1, 1976

By C. McAllister, D. Preece, J. Berendzen

"The Multiple Blasthole Fragmentation (MBF) model models multiple explosive charge contributions and the effect on fragmentation of delay timing with its associated scatter for each blasthole. The model uses near-field blast vibration attenuation parameters and the ground p-wave velocity as inputs for part of the in situ rock property to model rock fragmentation. It models most blast design parameters explicitly and simulates the effect of wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges within a blasthole or among blastholes. The fragmentation size is calculated at three-dimensional grid points within a blast, and the fines and oversized blocks are treated explicitly. The model takes a surveyed irregular geometry of the free face of a blast as the calculation boundary.This paper presents a case study on applying the MBF model at an openpit mine. Near-field vibration measurements from signature hole blasts were conducted to obtain the stress-wave magnitude and attenuation parameters as well as ground sonic velocity. A production blast was then monitored with the corresponding fragmentation measured, serving as site-specific inputs to the MBF model. Various blast design scenarios were then simulated to develop ones that provide better fragmentation to improve mill throughput for the mine. IntroductionThe semiempirical fragmentation models currently found in the literature (Cunningham, 1987; Lownds, 1995) cannot explicitly model contributions from multiple blastholes with varying delay intervals. Most of these models are not three-dimensional. Furthermore, these models predict an average fragmentation size within a volume surrounding a blasthole and use the average size to generate a size distribution over the volume. The percentage of fines and oversize blocks is included in the distribution. Typically, such models are inadequate for predicting fines and oversize blocks (Cunningham, 1987)."

Oct 1, 2016

By M. D. Loy

In addition to products available from private vendors, many useful programs are developed at universities - in fact, many of these programs led the way to commercial development. Other projects are assigned to consultants with backgrounds in system design and mining. Both types of development have led to programs that can be acquired for the cost of a tape or disk. This paper highlights several underground mining packages. These programs consist of: ? USBM model-developed by the United States Bureau of nines. ? PSU model-developed by Pennsylvania State University. ? VPI model-developed by Virginia Polytechnical Institute and State University. ? NUS model-developed by NUS Corp.

Jan 1, 1987

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor --will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Jan 1, 1997

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

By Quispe Mamani, Mayra Casas Azañero

The research is located within Asuncion and Cospan districts, which according to their geological features in contrast with previous studies pointing out Au, Mo and Pb anomalies create an environment of prospective interest. The objective is to use ASTER Satellite Images to identify ore-bearing hydrothermal alteration zones. To do this, processing techniques such as the combination of bands by RGB 943 and 461, band ratio 4/6, 4/5, 5/8 and 2/1 to identify advanced argillic, argillic to phyllic and propylitic alterations. In addition, indices defined by Ninomiya were used as a third technique in order to reinforce the data obtained from the previous techniques. The results in the study area are confirmed by the SAM spectral mapping technique using spectral signatures from the USGS library. Identifying kaolinite, alunite and pyrophyllite, assemblages of the advanced argillic alteration. Concluding in 3 areas of interest with the band ratios, 5 areas with the Ninomiya indexes and 9 areas validated with SAM, which were contrasted in 13 areas of prospective interest with well-marked argillic alteration.

Feb 1, 2025

By William C. McBee

A sulfur concrete technology has been developed by the U.S. Department of the Interior, Bureau of Mines, in which chemically modified sulfur is utilized with suitable mineral aggregates to produce construction materials which are resistant to corrosion by acids and salts. This report presents a summary of the basic technology and results of testing the materials under actual operating conditions in 50 corrosive environments in 40 commercial plants. After 4 years of testing, there was essentially no evidence of material degradation or loss of strength. Regular concrete materials were attacked and in some cases completely destroyed under the same conditions. Testing is continuing to establish ultimate longevity and durability of the sulfur concretes. The materials are finding widespread applications in metallurgical, chemical, and fertilizer processing plants.

Jan 1, 1983

The global mining industry will always face significant challenges. Some, though, are bigger than others. What do you consider the major challenges facing the mining industry as a whole and SME in particular? Without a doubt, the major issue in both coal and metal/nonmetal mining industries is the ?graying? of the workforce in all aspects of mining. As the baby boomers continue to age, valuable experience is being lost by industry, government and academia. And there is the potential for SME to lose some of its membership. Now with that said, I should note that, despite the aging of the workforce, SME membership continued to grow by 7.1 percent during 2011.

Jan 1, 2012

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the United States for the detection of fire in the belt entry and the monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data have the potential to provide fire characteristic information such as fire growth — in terms of heat release rate — and exact fire location. Such information is critical in making decisions regarding firefighting strategies, underground personnel evacuation and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide concentration, carbon dioxide concentration and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division’s Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy.IntroductionFires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases.The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke and toxic gases are produced and transported by the ventilation system and which provides an indication of the time available for escape or firefighting (Babrauskas and Peacock, 1992). The HRR is also an important input parameter to mine fire simulation models."

Jan 6, 2017

In this paper, we present design and implementation details of a fuzzy-behavior-based controller for an automated excavator. This robotic excavator must be equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered from bucket mounted force sensors during the excavation process. Implementation details and experimental results using the fuzzy behavior based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining excavator controller.

Jan 1, 1996

When Caterpillar announced that it had purchased Bucyrus for $8.8 billion, it was billed as the next great chapter in the history of mining. Surely, when the history books are written, it will be remembered as a deal that changed the face of the mining equipment sector, and it could well be a major milestone in the path toward autonomous mining in the future. In the short term, the deal is a clear indication that the world?s largest equipment maker is bullish on the mining sector. The purchase of Bucyrus allows Caterpillar to expand its mining interest to six product segments (underground, surface extraction, large mining trucks, surface material handling, hauling products and growth markets) with 16 product lines to serve the mining industry. But the commitment doesn?t end there. According to Steve Wunning, president of Caterpillar?s resource industries group, which includes Cat?s global mining division, the commitment to mining goes far beyond the acquisition of Bucyrus.

Jan 1, 2011

By I. Abdullayev, M. Soberano Capistran, J. Garcia

The application of post-tensioning in segmental structures was introduced in the early 1900s and has been successfully applied in different types of structures including immersed tunnels, bridges, buildings, metro stations, and stadiums. There are, however, only five known circular concrete tunnel projects where the post-tensioning approach has been adopted. This paper discusses the application of post-tensioning to mitigate the high internal operating pressures in an effluent outfall tunnel project 7 miles, 11.3 km long, currently under construction for the Los Angeles County Sanitation Districts, LACSD. This project will be the first use of post- tensioned segmental concrete tunnel linings in North America.

Jun 23, 2024