Search Documents

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Mobile RAs have a limited ability to dissipate heat, and heat buildup can lead to a life-threatening condition as the RA internal air temperature and relative humidity increase. The National Institute for Occupational Safety and Health Office of Mine Safety and Health Research performed heat testing on a 10-person tent-type training RA and contracted ThermoAnalytics, Inc. to develop a validated thermal simulation model (TSM) of the tested RA. The TSM was used to examine the effects of the constant mine strata temperature assumption, initial mine air temperature (MAT), initial mine strata surface temperature (MSST), initial mine strata temperature at depth (MSTD), and mine strata thermal behavior on RA internal air temperature using 117 W of sensible heat input per simulated miner. For the studied RA, when the mine strata temperature was treated as a constant, the final predicted RA internal air temperature was 12.8°F lower than it was when the mine strata thermal behavior was included in the model. A 10°F increase in the initial MSST resulted in a 7.1°F increase in the final RA internal air temperature, whereas a 10°F increase in the initial MSTD yielded a 2.5°F increase in the final RA internal air temperature. INTRODUCTION Since 2008, the Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (1). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. NIOSH recommended an apparent temperature limit of 95°F in its 2007 report to Congress (2). In 30 CFR 7.504, MSHA has specified a maximum apparent temperature of 95°F inside an occupied RA (3). The apparent temperature is calculated using both air temperature and relative humidity (4). Calculations could be used to determine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, in order to simplify the problem, the mine temperature could be assumed to remain constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. OMSHR research has shown that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (5). Thus, calculations performed with the assumption that the mine temperature is constant would under-predict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, research has not been used to confirm that the mine air temperature is the appropriate basis."

Jan 1, 2016

The purpose of the 3DOPT Program is to determine, starting from drill hole data, the optimum economic mining limits for an open pit. The economic limits are defined as those which maximize total profit, i. e. total mineral value mined less the total mining and milling costs, subject to the restriction imposed by the pit slopes. To accomplish this, the program employs the following: (1) A three dimensional matrix of equal sized blocks in order to file the engineering data and the cost/value data required to develop the profit figure for each block of ore/waste. (2) A graph algorithm developed specifically for optimizing these profits.1

Jan 1, 1966

By Andrew M. Wala

The determination of air quantity needed to dilute the exhaust gases to a safe level has to be individually evaluated for particular cases. The diesel powered machines are doing some specific operations in the cyclic order required by the technical process. The dynamics of this process in certain conditions has an essential influence on environmental health conditions in the working area. The main purpose of this paper is to show, using computer simulation, how the movement (dynamic) of diesel vehicles effects environmental health standards and also how to determine the required air quantity for certain conditions

Jan 1, 1983

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By Roy Norcross

For the past few years Caro's acid has been used for the treatment of cyanide containing slurry effluents, providing a feasible alter­ naive to other slurry treatment processes including !NCO SO2 / Arr and ferrous sulfate. Presently, mines using Caro's acid gen­erate their own Caro's acid onsite making a relatively low quali­ty product. It was at this point where we, at Degussa Corporation, decided to focus our efforts on engineering a Caro's acid genera­tor capable of cost effectively producing a high quality Caro's acid solution, thus reducing operating costs significantly. Caro's acid or peroxymonosulfuric acid is not a new chem­ical nor is it new to Degussa. The product was named after Heinrich Caro (1834-1910), a German chemist who first described its synthesis and its oxidizing properties in 1898. Degussa has been producing the potassium salt of Caro's acid as the triple salt, 2KHSO5 - 2KHSO4 - K2SO4, called Caroat®, for over 30 years. Caroat® is used for household and denture cleansers, as a bleaching agent in dish washing detergents, in printed circuit board etching and for cyanide destruction in the plating industry. From our experience in producing Caroat® Degussa developed its new Caro's acid based DegOX™ technology for the treat­ment of cyanide containing effluents from gold and silver mines.

Jan 1, 1996

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By Leslie C. Thompson

The heap leach process used for recovering gold from oxide and sulfide ores is operated as a closed circuit system in which the cyanide process solutions are continuously recy­cled. In a well-designed operation there is little or no dis­charge of cyanide to the environment. Spent leached ore residues are water washed to remove most of the trace cyan­ides and precious metals remaining after completion of cyan­ide leaching. After the washing step, small amounts of cyanide, metal-cyanide complexes and nitrates remain in the residue. Most of the cyanide and nitrate residue constituents exist in the pore water of the spent ore rather than in the solid mineral fraction. More than 90% of the complexed cyanides in a freshly washed ore residue are present as free cyanide or weakly complexed metal-cyanides. Natural volatilization and decom­position rapidly remove most of these easily dissociable cyanides from the spent ore. Only the stable, strongly com­plexed metal-cyanides, such as gold, cobalt or the ferrocyan­ides and other constituents such as nitrates have a long term persistence in the spent ore residue (Towill et al). Despite washing and natural removal mechanisms, spent ore has the potential to act as a point source of com­plexed cyanides and nitrates for soil and groundwater con­tamination if inadequately contained (Huiatt et al). The groundwater contamination is caused by the leaching of the soluble cyanide compounds and nitrates from the pore water of the residue.

Jan 1, 1990

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By Fred H. Seymour

In spite of the progress made by geostatistical theory over the years, evaluation of low grade open pit gold deposits continues to be challenging. Many Carlin type deposits are modelled from exploration drilling spaced on 10C foot centers. From these drill holes, 50 by 50 by 20 foot blocks containing about 4000 tons of material are estimated. The block size is a compromise between being large enough for a good geostatistical estimation and being small enough for practical pit limit analysis and mine planning. Most of these gold deposits are highly variable and include ore and waste zones that are too small to be properly defined from exploration drilling information. Because of this, selective mining is controlled by sampling closely spaced blast holes where the density can be as high as 50 blast holes per exploration drill hole intercept. Figure 1 illustrates an example of the ore/waste contact definition before and after blast hole sampling. With exploration information only, a tentative ore/waste contact can be drawn between the exploration blocks.

Jan 1, 1989

By Jerry Grott

Southwest Salt Company is solution mining the Luke Salt Body of probable late Miocene age. The discovery hole, from which the first core was recovered, was drilled in 1968. The deposit was encountered at a depth of 880 feet, and the bit was still in salt at the bottom-hole depth of 4,500 feet. The solar ponds, developed on land formerly dedicated to agriculture, have an annual capacity of about 90,000 tons. Because land values are very high, mining rates and procedures are governed by the need for near-saturated brine to minimize land requirements. Because of the frequency of dust storms, the salt operation uses a unique wet-harvesting method. Most inventory is kept in the ponds under brine and harvested only a few days before shipment. Studies of the nature of crystal growth and the distribution of windblown and brine impurities led to the development of procedures for processing salt of high chemical purity and low insolubles content. Chemical purity exceeds that of most salt produced in fuel-fired evaporators. Salt is shipped from Phoenix as tar east as west Texas and as far west as central California. Occasional shipments have been made to Hawaii and Alaska.

Jan 1, 1987

By Clinton A. Hollingsworth

The Flotaire Flotation Cell is a simple, efficient hydraulic/pneumatic Flotation Cell that has no moving parts. It is normally used in conjunction with a surfactant (frother) in which case the combination is known as "The Flotaire System". On many ores, metallurgical efficiencies are substantially increased and operating costs reduce. For example, in floating phosphate rock, it is not unusual for BPL recovery to be increased more than 10%, the major increase being due to floating coarse phosphate, up to 14 mesh, and the difficult to float phosphate. Substantial improvements have also been made on coal, mica, vermiculite, kaolin, barite, copper, etc.

Jan 1, 1981

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

By R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using either a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion, and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent.

Jan 1, 1990

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By M. G. Eiselein, R. A. Smith, C. H. Sheerin

FMC Gold's Paradise Peak Mine was one of the top two producers of mercury metal in North America in 1988 and 1989. As a by-product, elemental mercury is produced from cyanide soluble mercury minerals, primarily to reduce the health risks incurred with the refining of precious metal precipitate containing elemental mercury and mercury amalgams. A discussion of the design, primarily the Merrill-Crowe units, and permitting for the safe production of mercury will be presented. Additionally, laboratory testwork to determine the effect of mercury on reagent requirements in the Merrill-Crowe process will be discussed.

Jan 1, 1990

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By J. Herman

The Mid-Continent Geophysical Anomaly (M.G.A.) which extends from Michigan into Wisconsin, Minnesota, Iowa, Nebraska, and Kansas, has recently been the object of intense preliminary oil and gas exploration activity involving widespread land leasing, seismic data collection, permitting of deep exploratory holes and other activities (Paul et al., 1985). This report describes the remote-sensing techniques and results of the application of these techniques to study the geology of the M.G.A. and the surroundings in Iowa. In early 1981, Coal Valley Natural Resources contracted Geospectra Corporation to find a large, (100,000 acres or larger) lease block for wildcat oil and gas exploration. The southwest Iowa area was chosen for several reasons. First, southwest Iowa contains the northeast portion of the Forest City basin (Figure 1) which has produced oil and gas from numerous fields in Kansas, Missouri, and Nebraska (Landes, 1970; Petzet, 1982).

Jan 1, 1986

By Michael J. Friedel

The permeability and flow capacity in unsaturated media is investigated by the Bureau of Mines for application to in situ copper leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through rubblization. By producing a maximum block diameter of 4 m, injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 1991

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974