Search Documents

By P. Munjal

"Usage of Supercritical CO2 in place of high pressure freshwater has proven to be a potential breakthrough in the technique of fracturing. Tapping of carbon footprints from feasible sources like industries can be used to manufacture Supercritical CO2 required for fracking. Supercritical CO2, being less viscous than water, creates complex and coherent micro-fractures which can connect many more natural fractures greatly, increasing maximally the fractures’ conductivity leading to an increment in production. The better clean-up property of Supercritical CO2 provides auxiliary benefits of immediate evaluation of fracture zones, usage of an optimized quantity of mesh proppant and elimination of the need of swabbing. Also, Coal has a stronger affinity for CO2 than for CH4. When CO2 is present, CH4 on coal is replaced by CO2. This also ensures rigorous recovery of gas from the coal beds. Use of Supercritical CO2 will obliterate many problems as the CO2 used for fracturing is either sequestered beneath the crust or is recovered at the surface and reused. Therefore, injecting CO2 into coalbeds achieves not only enhanced CBM recovery, but also greenhouse sequestration underground. INTRODUCTION Coalbed Methane At various times in the geologic past, earth had dense forests in low-lying wetland areas. Due to natural processes such as flooding, these forests were buried underneath the soil. As more and more soil deposited over them, these dead plant remains were compressed. As the process continued the plant matter was protected from biodegradation and oxidation, usually by mud or acidic water. Under high pressure and high temperature, dead vegetation was slowly converted to coal. The omnibus process of formation of coal, thus, comprises of conversion of dead plant matter into peat, followed by its conversion to lignite, then sub-bituminous coal, after that bituminous coal, and lastly anthracite. This process of enrichment of coal as it is progressively forced deeper into an ambience with higher temperature and pressure involves biological and geological processes that take place over a long period and is called coalification. During coalification, large amounts of methane-rich gas are generated and stored within the coal on internal surfaces; hence comes coalbed methane. Coalbed methane (CBM), a gas formed as part of the geological processes that are responsible for the generation of coal, is adsorbed into the solid matrix of the coal during its formation process. Coalbed methane is distinct from a typical sandstone or other conventional gas reservoirs, as the methane is adsorbed and not absorbed. The methane is in a near-liquid state, lining the inside of pores within the coal. The open fractures in the coal that result from the liberation of volatile materials (and subsequent contraction due to the liberation) from the coal due to the high temperature and pressure conditions encountered, called cleats, may also contain free gas or can be saturated with water."

Jan 1, 2015

By Y. A. Attia

A study was performed on selective flocculation and dispersion for ultrafine coal cleaning. A totally hydrophobic polymer, FR-7A, was employed as the selective flocculent for coal, sodium metaphosphate (SMP) as the general dispersant for shale and a synthetic polymeric product, polyacrylic acid-xanthate (PAAX), as the selective dispersant for pyrite. In the adsorption tests, nephelometry and spectrophotometry were employed for determining the concentration of FR-7A and PAAX in the solutions respectively. The adsorption tests indicated that: a) FR-7A has a higher affinity toward coal and pyrite than that for shale; and b) PAAX has a much higher affinity toward pyrite than toward coal and shale. In the selective flocculation tests, the ash-forming minerals can be efficiently rejected using sedimentation as the separation method. However, due to their relatively high specific gravity, pyrite particles co-settle with the coal flocs. To reject fine pyrite, a froth flotation was used for floc separation. The one-step flocculation-flotation process could reject more than 70% of each of the pyritic sulfur and ash minerals, while recovering more than 85% of the coal.

Jan 1, 1990

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of'these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990

By H. S. Duzgun, N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline’s long-term availability, to develop preventive maintenance plans and to make future projections about the dragline’s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, Page 736 and Marion 7820, which have been operating in the Tunçbilek openpit coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data and (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (15.29 m3) seemed to be more reliable and less likely to fail when compared with Marion 7820 (30.58 m3). The operating hours without failure range from 41 to 51 hours with 50% reliability.

Jan 1, 2011

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By S. P. Brown, J. E. Worthington

Increasingly, exploration geology seems to be growing into a practice overly separated from production geology, yet the eventual purpose of exploration is a producing mine. To help in the search for new deposits, exploration "lessons" will be drawn from the papers given at the Fall AIME Applied Geology Symposium. In addition, examples will be re-emphasized to show how early observation of matters now routine to mine work (for example, hydrology, rock mechanics, oxidation state) can help increase the effectiveness of exploration.

Jan 1, 1992

By E. J. Rorem

Rockfall and unstable rock slopes can be con-trolled by using steel wire-rope net systems as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting. This flexibility and strength permits kinetic energy dissipation with low maintenance requirements. Mining activities can produce temporary or long-term unnatural slopes and unstable rock faces that may produce rockfall hazards. Such conditions can necessitate efforts to minimize the hazard to workers, structures and equipment.

Jan 1, 1996

By Frank F. Aplan, G. Rinelli

INTRODUCTION Coal is a solid, combustible mineral substance resulting from the degradation and alteration of vegetable matter largely in the absence of air. In this natural process of coalification, some non-combustible mineral matter is always associated with the combustible material. Coal preparation or cleaning is the process of removing this inert mineral matter from the coal. Preparation is highly successful in removing the large fragments of inert material, but is not very effective in removing the fine inorganic mineral matter intimately associated with the coal. Of the 600 million tons of coal produced in the United States every year, approximately one-half is produced by coal cleaning methods (1). The bulk of this tonnage is cleaned by coarse or intermediate gravity preparation methods (5 inches to 28 mesh, Tyler). Fine cleaning, say, -28 mesh, is done by shaking tables, washing cyclones, and flotation, or, until recently, the fines were either incorporated into the clean coal or simply discarded--not infrequently, the latter. In 1972, only 13 million tons of raw coal were cleaned by flotation in the United States, and from this 8.4 million tons of clean coal were produced (1). The percentage of clean coal produced by flotation in Europe (England, West Germany, Poland, U.S.S.R., etc.) is substantially higher. However, coal flotation has grown rapidly in the United States from only a few plants in 1950 to 31 in 1960 (2) and 66 in 1970 (1). Virtually all new preparation plants incorporate flotation into their basic flowsheet. The essential difference between ore and coal flotation is that for ores the entire tonnage is ground to flotation size, whereas for coal

Jan 1, 1976

By W. Zhang

"The adsorption of collector on chalcocite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on chalcocite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. The result clearly shows that the adsorption of xanthate on chalcocite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. AFM images also showed that increasing solution pH to 10 doesn’t prevent the adsorption of xanthate on chalcocite much and the result confirms with the fact that chalcocite floats well in a wide pH range up to 12 with xanthate being used as a collector. INTRODUCTION In flotation, the adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying metal recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) The adsorption of xanthate on chalcocite surface in aqueous solution also attracted the interest of many researches. Gaudin and his colleagues (Gaudin et al., 1934; Gaudin and Schuhmann, 1936) studied the solubility of potassium ethyl xanthate and its reaction products in organic solvents and firstly proposed there was initially chemisorbed xanthate (X-) on chalcocite surface followed by insoluble cuprous xanthate (CuX). Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of chalcocite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on chalcocite was cuprous xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Richardson et al. (1984) carried out an electrochemical study of chalcocite flotation with the addition of ethyl xanthate. It was proposed that cuprous xanthate and possibly cupric xanthate were adsorbed hydrophobic species on chalcocite surface due to the exchange and charge transfer oxidation reactions. Leppinen et al. (1989) applied an in-situ FTIR study of ethyl xanthate adsorption on sulfide minerals under conditions of controlled potential and they concluded that, for chalcocite, there were three different potential regions of xanthate adsorption, including chemisorption, copper ethyl xanthate formation on the surface and multilayer formation."

Jan 1, 2015

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By C. Roos

"Nearly every input to a mine plan is based on an estimate. The estimates may be from sample data, historical information, models, or personal opinion, but in all cases, these values are simply expected values (means). In real life, we do not get to iterate the exact conditions at our mining operation many times to ensure that that average value is attained. The expected value also tells us nothing about the spread of values that that input might take on. The result is a significant amount of unquantified uncertainty in our mine plans. Unfortunately, it is often too expensive or time consuming to update planning processes and software. This paper presents a proof of concept spreadsheet scheduling tool that can be utilized to incorporate many geologic realizations (simulated models) into the mine scheduling process. While this POC is not intended to be a detailed model of uncertainty, it is to show that there are stepping stones available for mine planners to begin to embrace uncertainty and produce more achievable plans without requiring a significant change in their planning process. INTRODUCTION Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years, however many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize and even embrace the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process. Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple ore body realizations to provide a thorough unbiased “picture” of the geologic uncertainty but most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter. Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this paper presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid to long-term mine plans while continuously monitoring the uncertainty in the results. The author hopes that by demonstrating the usefulness of such a system that mining companies will encourage engineers, geologists, and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 1, 2017

By Robert G. Bottge, Paul C. Hyndman, Don J. Barnes, Clark A. Roberts

The effect of Federal restrictions on Federal mineral estate in Alaska and the Western States is being addressed by systematic, State-by- State studies. The Bureau of Mines has inventoried and classified 3.5 million sq km (876 million acres) of land, section-by-section, according to 1) mineral ownership, 2) availability for mineral exploration and development as affected by Federal restrictions, and 31, areas containing mines and mineral resources. The availability of Federal land for exploration and development is spatially compared to areas containing mines and mineral resources. The methodology and overall results of the studies are presented.

Jan 1, 1991

By G. W. Poling

Chemical and physical properties of thiol collectors are reexamined to compare the prospects of heavy metal-thiolate or disulphide surface reaction products acting as actual collector species. Recent evidences for the existence and importance of each of these types of adsorbed species on sulphide minerals are also discussed. A conclusion is reached that partial coverage by chemisorbed heavy metal thiolate is often sufficient to confer practical levels of hydrophobicity and floatability. Only on a few highly conducting and "noble" sulphides does adsorbed disulphide-type collector oxidation product appear to be significant.

Jan 1, 1976

The dissolution behavior of gold and silver from Au/Ag alloys in aerated cyanide solutions has been investigated using rotating disc electrodes. The variables studied included concentration of cyanide, oxygen partial pressure and rotating speed of the disc. The dissolution potential and the rate of dissolution were obtained in view of the anodic and cathodic current-potential relationships. The results were discussed in terms of a mixed potential theory. The results showed that the dissolution rate of gold and silver from the alloys was partially controlled by chemical reaction, but largely by transport of either oxygen or cyanide, depending on their relative concentration under the experimental conditions employed in this study.

Jan 1, 1995

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998