Search Documents

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By J. P. Ducarme

The eastern U.S. contains vast reserves of thin seam coal deposits, particularly in the Appalachian mountain region. These typical 355 to 710 mm thick reserves are difficult or uneconomical to recover with present technology. The U.S. Bureau of Mines is developing technology that would allow nearly 100% recovery of thin seams in these mountaintop regions. This paper details the research that has been conducted on these new techniques and presents results of testing on a cross-ridge full-scale physical model.

Jan 1, 1994

By Nik Sokol, Eric Sekulski, Leo Weiman-Benitez, Jon Hurt, Shrinidhi Vijayakumar, Phaidra Campbell

The Silicon Valley Clean Water (SVCW) Gravity Pipeline (GP) is the first Progressive Design Build (PDB) tunnel completed in North America. As part of the Regional Environmental Sewer Conveyance Upgrade (RESCU) Program, the tunnel is a key component to replacing and rehabilitating components of the existing conveyance system in San Mateo County, California. The GP consists of a large diameter Fiberglass Reinforced Polymer Mortar (FRPM) pipe installed inside a 4.1 m (13.5 ft) inside diameter, 5.3 km (3.3 mile) long precast concrete segmentally lined tunnel. The tunnel was constructed using a 4.6 m (15.2 ft) diameter Earth Pressure Balance (EPB) Tunnel Boring Machine (TBM) through heterogenous silts, clays and sands. Construction included two separate TBMlaunches from a centrally located access shaft, and a tunnel alignment below but in close proximity to very soft Young Bay Mud. Settlement criteria and mitigation strategies focused on protection of an existing 1.42 m (56 inch) diameter force main and adjoining structures along the alignment. This paper discusses the results of the theoretical settlement analysis versus the actual observed ground movements, while also presenting mitigation measures and adjustments made during tunneling to reduce the risks of adverse settlement.

Jun 13, 2023

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Yoichi Shimada, Katsuyuki Nishida, Shinichi Takahashi, Yasushi Okada, Yohei Nakamichi, Kazunori Oshiro, Taichi Terui, Sigehiko Sugie

"Temporary retaining walls are ordinarily used for tunnel construction work conducted using the opencut construction method. Retaining walls in such instances are typically installed vertically. However, shoring (such as struts and king posts) is required to ensure the stability of retaining walls in cases of excavation work to depths that exceed approximately 4 m. A new design and construction method that focuses on the effectiveness of retaining walls that are installed on an incline was studied with the aim of improving construction workability by omitting shoring. The inclined braceless excavation support (IBES) method, which was developed for use with the inclined buttress method, requires no shoring, even for deep-open-cut construction work and can be applied to deep excavation work on ground with a high groundwater level. This method has been applied at six work sites in Japan in recent years. This paper introduces the IBES design and construction method and presents verification results based on the design method, a model experiment, finite element analysis, and measurements obtained during construction work.INTRODUCTIONBackgroundIn the past, temporary retaining walls used in open-cut construction work have been installed vertically, and shoring (such as struts and king posts) has typically been used to ensure the stability of these retaining walls when the excavation depth reached 3–4 m. However, shoring interferes with structures built within excavations and requires box-outs and penetration sections in the structures, as well as concrete joints that raise concerns about their impact on the watertightness and long-term durability of structures (Figure 1).Shoring also narrows the space available for conducting construction work and reduces construction work efficiency, and the installation and removal of shoring increases the construction duration and cost. As a result, there has been a demand for ways to reduce or eliminate shoring to improve the quality of structures and construction work efficiency."

Jan 1, 2016

The dissolution kinetics of cobalt in iodine/iodide solutions was investigated using a rotating disc technique. Variables studied here included temperature, rotating speed, concentration of lixiviants, and pH of the solution. The overall dissolution reaction was found to be limited by mass transfer of tri-iodide through the diffusion boundary layer with Arrhenius activation energy of less than 16.2 kJ/mol (4 kcal/mol) over the temperature range, 2-42°C. The pH of the solution had little effect as long as the pH of the solution was less than 8. However, when the pH of the solution became greater than 8, the dissolution rate decreased dramatically due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1994

By M. Ziegler

The article deals with the use of a digital twin in the assessment and optimization of a conveyor system in the Chilean copper mine. This example shows that a digital twin is initially just a new (albeit powerful) tool with which the system behavior can be examined. The benefits for the customer arise through the system identification and automatic detection of critical deviations from the target state. This knowledge allows mine management to react and coordinate operational and/or maintenance counter measures to insure optimal performance of their conveyor system. The information derived from the BeltGenius digital twin also allows mine management to gain a clear perspective of the overall efficiency of their conveyors, which will be invaluable for future conveyor component selections.

Mar 2, 2022

By Daniel A. Jones

The Surface Mining Control and Reclamation Act of 1977 establishes a nation-wide program requiring the Secretary of the Interior, through the Office of Surface Mining Reclamation and Enforcement, and the States to protect against the adverse effects of coal mining and to reclaim previously mined lands left without adequate reclamation. The Act requires coal mine operators to: restore the land to approximate original contour, return the land to a condition capable of supporting prior potential uses, protect the hydrologic balance, segregate and restore topsoil, control blasting to prevent damage and injury, establish vegetative cover, and control surface effects of underground mining. The Act also establishes: a reclamation fee on coal, a program to assist small operators, a program to give technical and financial assistance to State programs, State Mining and Mineral Research Institutes., a program for designating areas as unsuitable for mining, and a study on surface mining of minerals other than coal.

Jan 1, 1977

By G. T. Lineberry

There is a critical need for effective instructional materials at the university level and for an upgrading of mine safety and health in the mining engineering curriculum. A fundamental approach to mine safety and health is recast into the familiar 3 E's: engineering, education, and enforcement, in that order. Each is briefly reviewed and their interdependence emphasized. A unique philosophy for successfully integrating safety and health principles into the mining engineering curriculum is offered. The concept of textbook ?tailoring? is discussed and defended, permitting rapid assemblage and synthesis of existing educational materials. Final recommendations are made for a u, comprehensive approach to mine safety and health education in the undergraduate curriculum.

Jan 1, 1987

By Ehsan Moosavi, Kamyar Tolouei, Mehran Gholinejad

The literature defines rockbursts in slightly different ways based on their generation mechanisms, field phenomena, and degree of damage, but in a way that is almost consistent. Generally, a rockburst refers to seismic events that mainly happen in underground excavations, for purposes such as underground mining, road and railway tunnels, nuclear power, etc., and that are followed by the collapse and outburst of rocks. Long-term rockburst prediction can be abstracted as a classification problem mathematically, in which we can introduce deep learning to solve it. Further, using deep learning in rockburst prediction can overcome drawbacks such as subjectivity and inconsistency brought from previous traditional approaches. A rockburst data-set, was employed to evaluate the current method for predicting rockburst grade, and the good results of overall success rate were obtained. The results indicated that the proposed algorithms can speed up parameter optimization search, the proposed method is robust model and might hold a high potential to become a useful tool in rockburst prediction research.

Apr 26, 2022

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By J. M. Dean

The MANpower SUPport Program (MANSUPP), a part of the Mine Management Support System (MMSS), allows an underground coal mine site user to determine manpower requirements for production support work by considering ongoing operations and current mine conditions. The objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and management preferences to predict required manhours for various activities, for example, belt moves. The program is written in Quattro Pro version 3.0 (Lotus 1-2-3 compatible) utilizing the command language, macro and formula capabilities.

Jan 1, 1992

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By G. A. Kordosky

Solution mining followed by solvent extraction-electrowinning (SX-EW) is one possible way to economically extract copper from ore bodies which cannot otherwise be profitably exploited. Published costs for the unit processes of SX and EW are out of date especially in view of the newer reagents now available and the newer circuit configurations, This paper updates the costs for SX-EW in 1985 dollars and also discusses some of the trade-offs which must be made when designing an SX-W plant.

Jan 1, 1986

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By T. Skodack

This presentation will compare actual work site results for the loading and transport of shot rock for two major tunneling projects in North America. "SCARMAR" (the Canadian subsidiary of S & M Construction) is operating a rail bound Hagglund continuous gathering arm loader in combination with a Hagglund nine car shuttletrain system at the West End of Table Mountain on the B.C. Railway project near Tumbler Ridge, Canada. Al Johnson Construction is operating a Hagglund rubber tired continuous gathering arm loader in combination with haul trucks at the Rocky Mountain Pump Storage Project near Rome, GA. This paper will compare: 1) tunnel and ground conditions, 2) the total work cycle as it relates to mucking and haulage 3) efficiencies and related problems with the two systems 4) mucking and haulage rates 5) operating costs, and 6) recommendations for future large tunnel excavations. Manuscript not received in time for publication.

Jan 1, 1983

The viability of physico-chemical purification methods such as selective flocculation for separation of two components having similar chemical composition and same crystal structure but different surface properties is demonstrated. Loss of selectivity was observed in a dolomite-dolomite mixture with Polyethylene Oxide (5 million molecular weight) as the flocculant. Hetero-flocculation was minimized using a low molecular weight PEO (MW -105) as the site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at 100% recovery level.

Jan 1, 1993