Search Documents

By B. F. Dickerson

STRATEGIC METALS! Recently, this money accented cry has been heard in such diverse locales as Mining company boardrooms, Banker's offices, Stockbroker's quarters, Swindler's dens and Congressional committee rooms. (In some cases, these locales are one and the same). Is the strategic metals rush for real? Should it be? Our paper attempts to give a very generalized view of the subject for a few metals, points to a few potential, but generally overlooked sources of these metals, and offers conclusions based on our studies.

Jan 1, 1981

By M. Scaggs, K. Phillips

"Coal Worker’s Pneumoconiosis (CWP) is an occupational lung disease caused by chronic exposure to respirable mine dust. After decades of steady decline, CWP incidence appears to be on the rise since the mid-1990s, particularly in some regions of Appalachia. Alarmingly, many of these cases have rapidly progressed to the most advanced form of CWP, referred to as Progressive Massive Fibrosis (PMF). Most of what is currently understood about respirable mine dust has been gleaned from routine regulatory monitoring, which tracks total mass concentration of respirable dust (mg/m3) and, less frequently, silica mass content. This paper focuses on the use of thermogravimetric analysis (TGA) as a way to provide basic characterization of the whole composition of the dust, allowing it to be classified into three mass fractions – coal, carbonate, and non-carbonate minerals. TGA was conducted on 59 dust samples collected by miners from eight coal mines in central Appalachia, and the results are discussed in terms of differences between mines, regions, and primary occupations. Consistent with prior results on area dust samples from some of the same mines, results of the personal samples generally show that the coal mass fraction of the dust is relatively low. Carbonate and non-carbonate minerals thus tend to make up the bulk of the dust mass, and vary across occupations and specific mines. INTRODUCTION After nearly four decades of decline, the prevalence of Coal Workers’ Pneumoconiosis (CWP, or “black lung”) in the US has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of progressive massive fibrosis (PMF), which is the most advanced form of the disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 US coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85%) that had a normal radiograph on file to use as a baseline, 27 (17%) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84%) of the individuals in that study worked in KY, WV or VA, and 169 (88%) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern KY. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, these recent reports may well overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression – such that effective interventions can be devised."

Jan 1, 2018

An AFM has been applied to study in situ the adsorption of oleic acid on fluorite in aqueous solutions. The AFM images show that fluorite surface becomes smoother with the adsorption of 7 × 10-5 M oleic acid solution at pH 9. Force measurement shows that fluorite is strongly positively charged in water at pH 6, suggesting a neglectable surface carbonation of fluorite. The adsorption of oleic acid at pH 9 renders fluorite more and more negatively charged. The surface morphology change of fluorite as shown by the AFM images suggests that oleic acid chemisorbs on fluorite at pH 9. Increasing temperature can help increase the adsorption of oleic acid on fluorite. It may also improve the lateral polymerization of unsaturated oleic acid on fluorite as suggested by the smoother mineral surface in oleic acid solutions at an elevated temperature.

Feb 23, 2014

Bigger is indeed better in today's surface mining operations. That is especially true regarding haul trucks. Building larger, "supersize" trucks, however, means designing more powerful engines and drive systems that are also more efficient and environmentally friendly. And miners are demanding that these trucks have longer service lives with minimum maintenance. So truck makers are teaming with engine manufacturers and mining customers to design these larger trucks that will ultimately lead to reduced mining costs. About 180 of those truck makers, engine designers and miners gathered in Tucson, AZ in September to discuss the state of haul trucks in today's mining environment. Haulage 2000 was sponsored by World Mining Equipment and attracted attendees from around the world. Manufacturers described the latest in haul truck advancements. These included the design of more powerful engines, improvements to mechanical and ac and dc drive systems and suggestions on how to reduce maintenance spending. Technology improvements in tires for larger struck was discussed as was the cost efficiency of new, lighter-weight bed liners. The following is a summary of a handful of the presentations.

Jan 1, 1997

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By J. S. Hall

The performance of a full-scale balling drum circuit is well known to fluctuate, and is difficult to control. The fluctuations stem from causes that are not readily quantifiable. Results from plant tests show that surging of the recycle tonnage is dependent, inter alia, on the method of bentonite addition, small variations in drum or cutter bar speed and the method of drum water addition. This paper presents detailed observations from experiments on full-scale drum circuits, including preliminary results of a computer measurement and control scheme. Size distributions measured at points along an industrial drum are presented, together with the results of a mathematical model fitted to one plant data set. Model predictions are also included emphasizing the importance of screen performance on circuit stability.

Jan 1, 1983

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England&apos;s largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford&apos;s salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By D. M. Anderson

The current mine closure process is faced? with the formidable challenge of controlling environmental and legal liabilities that are associated with mine closure. The current level of environmental statutes and regulations, and the legal/liability considerations, has evolved through regulatory enactment of mine reclamation laws and other existing environmental laws, such as the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Management tools and techniques to limit risk exposure and financial losses should be employed as an active measure throughout the mine life, including closure and post-closure.

Jan 1, 1995

By R. W. Wotring

Mr. Chairman, Officers, Members and Guests of the AIME, I want to express my appreciation for the privilege of being on your program at this meeting. Coal mining, in recent years, has become much more competitive than it formerly was. To stay in business, it has been necessary for coal mines to mechanize. This, in itself, has not been enough for after one has mechanized his mine, he must keep replacing the equipment with the latest type and model machines. We, at Olga, have been doing this very thing for the past several years. Olga No. 2 Mine is located at Caretta, West Virginia, in McDovell County, about twelve miles south of Welch, It is a shaft mine, operating in the No. 4 Pocahontas seam. The thickness in the area, we are presently mining, varies from five to six feet. In some areas the immediate roof is slate, ranging in thickness from a few inches to four and five feet; in other places, the sandstone lies on top of the coal, This sandstone is about twenty-five feet thick.

Jan 1, 1961

By D. A. Karvonen

Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major new source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960&apos;s - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth with about 5 percent of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40 percent of known world potash reserves and its ten active mines account for some 25% of annual world production. The development of this resource was recognized to be important to the development of Saskathcewan. In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation&apos;s Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product and conducting all of the other activities necessary for a successful corporation competing in the world potash industry.

Jan 1, 1983

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

By C. J. Bise

Virtual Reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced fonn of computer graphics where the images are generated based upon where the user looks and how the user moves. As personal-computer-based (PC-based) instruction gains acceptance as an innovative approach to providing safety training, VR offers the capability of providing a multisensory, rather than merely a multimedia, mode of presentation. VR has been effectively used by the military for training tank commanders and by hospitals for training surgeons. However, these applications have been limited to small numbers of highly skilled participants. The purpose of this paper is to examine VR&apos;s potential for enhancing the hazard awareness of larger numbers of individuals in a broad-based approach to mine safety training, such as new-miner, annual-refresher, and independent-contractor training.

Jan 1, 1996

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine&apos;s cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By Yves C. Lizotte

Although blasting remains the most inexpensive method of fragmentation in hardrock mining, the significance of the costs of blast-induced rockmass damage in terms of mining efficiency and safety is becoming increasingly recognized. There is no straightforward and systematic method of adequately measuring blast damage in on-going mining operations. This paper considers various techniques available to measure blast damage, making particular reference to recent underground hardrock mine studies. It concludes by proposing a damage audit procedure for integration into routine mine production control.

Jan 1, 1996

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998