Search Documents

By U. Srivastava

In the processing of manganiferous ore, it is useful to control whether the manganese (Mn) goes to the iron product to produce ferromanganese, or to the slag for extraction as a high Mn product. This can be done by manipulating the thermodynamic conditions for manganese oxide(MnO) reduction to control whether it remains as MnO or converts to metallic Mn. Results are presented showing that during production of iron nuggets, reduction of manganese oxide (MnO) can be controlled by changing the furnace temperature and reductant composition appropriately.

Jan 1, 2010

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By Boleslav Taraba, Antonín Taufer

Thermovision monitoring of surface temperature has been examined for the purpose of detection of spontaneous combustion of early stage. Measurements were carried out in bituminous and subbituminous coal mines. It was found that surface temperature heterogenities can be considered as common phenomenon in mine openings. However, the most of the observed temperature heterogenities were not connected with coal spontaneous combustion of early stage. These, so called [non-spontaneous combustion] temperature heterogenities in surface of mine openings were found to be caused by: l. Different conditions of heat transfer between opening surface and air stream; 2. Low temperature (natural) oxidation of coal; 3. Dissipated heat loses of working machine. Sites of early stage spontaneous combustion of coal were characterized by: 1. More significant, local rise in surface temperature comparing with low temperature coal oxidation; 2. Evolution of carbon monoxide with local concentration near the surface of such site more than about 15 ppm (bituminous coals) or 30 ppm (subbituminous coals). INTRODUCTION Mine fires are a serious hazard to life and result in a considerable loss of coal reserves. Thus, great attention is paid to investigation of new methods enabling already early detection of self-heating of coal. The earlier a fire is observed, the easier would it be to deal with. Detection methods used in coal mines are mainly based on: 1. [Mine air analysis]. Changes in composition of mine air are examined. Products of spontaneous heating of coal, not being present in mine air under normal conditions, are considered as indicators of anomalous behaviour of coal (carbon monoxide, unsaturated hydrocarbons) (Mackenzie-Wood and Strang, 1990). 2. [Temperature measurements]. Sites of higher temperature level comparing surroundings are looking for underground using various direct or indirect methods of temperature measurements. This paper summarizes experience from thermovision monitoring, as one of the latest indirect temperature measurement technique, used for the purpose of early detection of self-heating of coal in mine openings. INFRARED THERMOVISION Infrared thermovision device of AGEMA Infrared systems AB (Sweden) was used for the in situ measurements. The constant value of emissivity factor, 0.95, was pre-set as the most probable level of emissivities of coal and rocks in mine conditions.

Jan 1, 1993

By M. K. McCarter

A unique telemetry system was developed to monitor potentially unstable natural slopes above a residential area. Continuous interpretation of data transmitted from remote movement-sensitive devices and immediate communication of signficant changes to emergency personnel were made possible by a readily available "home" computer. Even though the computer based system was originally developed for a non- mining application, it could be used with little or no modification to monitor ground control instrumentation in open pit and underground situations.

Jan 1, 1985

By T. Yue, Z. Gao, X. Tong, R. Liu

"Lead ions (lead nitrate) were introduced to modify the surface properties of scheelite, effectively and selectively improving the flotability of scheelite, with benzohydroxamic acid (BHA) serving as the collector. A series of experiments about the mode of addition and the ratio of lead ion to BHA were conducted and indicated Pb-BHA complexes were the active species responsible for the flotation. And two adsorption models of BHA on the surface of scheelite were established. For both the two adding methods, some kind of complexes formed by lead ions and BHA played a key role in the flotation process. Zeta potential, FTIR, and XPS studies indicated that the adsorption amount and intensity of BHA on the surface of scheetlie were larger by adding the reagents as a mixture. The mixed addition is conducive to form Pb-BHA complexes and improve the adsorption efficiency of BHA on the surface of scheelite, as well as the recovery of scheelite. INTRODUCTION Scheelite, as an important tungsten-bearing mineral, is nowadays utilized mainly by flotation (YIN and WANG, 2014; Sun et al., 2011; Gao et al., 2015; Gao et al., 2015). Flotation separation of scheelite from calcium minerals creates difficulties because of the existence of the same cation in the minerals and similar physico-chemical characteristics such as solubility, hardness, specific gravity, point of zero charge (PZC), etc. (Arnold and Warren, 1974; Deng et al., 2016; Deng et al., 2015; Ozcan and Bulutcu, 1993a; Yongxin and Changgen, 1983). The conventional collectors used in the flotation of scheelite ores are generally fatty acids or fatty acid derivatives (Bo et al., 2015; Oliveira and Sampaio, 1988; Shi et al., 2014; Sivamohan, 1988; Yongxin and Changgen, 1983). It is difficult to separate scheelite, especially from calcite, with these reagents because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface (Atademir et al., 1979; Changgen and Yongxin, 1983; Hiçyìlmaz et al., 1993; Hu et al., 2011). Therefore, it is almost impossible to separate them by fatty acid flotation without using any selective depressant. Although oleoyl sarcosine was used as a selective collector in the flotation of fluorite and siliceous scheelite ores (Ozcan and Bulutcu, 1993b; Ozcan et al., 1994), this selectivity is inadequate for a low-grade calcitic scheelite ore. Unfortunately, reagents such as organic colloids (dextrine, starch), quebracho, sodium phosphates, sodium silicate solutions containing polyvalent cations (hydrosols), etc. (Bo et al., 2015; Schubert et al., 1990; Shi et al., 2014; Yongxin and Changgen, 1983), used for calcite depression also depress scheelite to a large extent. Cationic collectors, such as amine and quarternary ammonium (Yang et al., 2015) and collector mixture (Gao et al., 2015) have been used to improve the scheelite flotation. However they have not been applied in industry due to the poor separation from silicate minerals."

Jan 1, 2017

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey's Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By M. S. Celik

Unlike most other minerals, electrokinetic measurements of calcium montmodonite (a clay mineral) and u1exite (a boron mineral) exhibit an unusual behavior. While the addition of monovalent salts such as NaCI and KCI is expected to compress the electrical double layer with a resultant less absolute charge, an opposite trend is observed. A set of systematic experiments with monovalent and multivalent ions has been carried out to understand the mechanism of this phenomenon Examination of the results reveals that the behavior of montmorillonite is dictated by the exchangeable divalent cations at the edges which undergo an exchange process with monovalent cations resulting in the reduction of positive charges. The solubility of ulexite, on the other hand, is found to decrease with increasing monovalent cation concentration leading to again an increase in the absolute negative charge.

Jan 1, 1996

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

By Jie Li, Longxiang Li, Wenbing Guo, Gaobo Zhao, Yuhang Hu

Surface subsidence caused by underground longwall mining is a very complicated process in time and space, influencing building and structures on the surface of the mining area, including houses, pipelines, and highway. The field monitoring data of surface subsidence are essential for protecting them. This study investigated the dynamic and residual subsidence characteristics of both the surface and the highway over a 730-day monitoring period on a longwall panel. Three monitoring lines (Lines 1–3) were established to monitor the subsidence process, and three stages were identified: initial stage of surface subsidence, active period of surface subsidence, and residual subsidence deformation stage. The maximum subsidence value on the highway (1,786 mm) was smaller than that on the surface (2,094 mm), and the maximum subsidence velocity on the highway (41.7–50.8 mm/day) was also lower than that on the surface (66.7 mm/day). During the residual subsidence deformation stage, both the surface and highway subsidence velocities decreased to below 0.6 mm/day. Furthermore, differences in subsidence characteristics between the surface and the highway were analyzed, with the subsidence value on the highway always being less than that on the surface, while the subsidence velocity during the residual deformation stage was not always lower. This could be attributed to the influence of dynamic loads from vehicles, which could induce additional residual subsidence on the highway. Further investigation into this phenomenon will be conducted in future research.

Jul 1, 2023

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By Charles G. Zink

Anthracite is widely known as a domestic or space heating fuel. The prevailing market ratio of domestic to industrial consumption was about 80 to 20 up until 1950. Since then it has been shifting until now the ratio index is about 50/50, exclusive of overseas export. Despite a declining domestic space heating market, the demand for industrial anthracite remains good. However, as a result of stringent air pollution regulations, there is a renewed interest in this low sulphur coal which cannot smoke under any conditions. Anthracite serves other important industries such as power generating, metallurgical, cement, ceramic, chemical, water sewage and industrial wastes filtration. Anthracite is an excellent natural source of carbon and may be utilized in many processes.

Jan 1, 1966

By L. M. Cenegy

The formation of scale is common in gold ore processing plants. A working definition of scale, applicable to the various scaling conditions found in gold ore processing plants, would be: "a hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water". The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem.

Jan 1, 1990

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By E. S. Forbus

A process for producing reductive bleach in-situ in kaolin slurries has been developed. The bleach is formed by mixing an iron sponge powder (-325M) with slurry treated with SO2. The process has been successfully demonstrated in production, and applied to several grades. The color, brightness, and viscosity of the bleached product is equivalent to or better than that of product bleached with commercial sodium hydrosulfite . The tested products can be bleached at a cost, which is 38-54% of those associated with the use of commercial bleach.

Jan 1, 1993

By Trevor R. Ellis

In this paper a method is presented for estimating the specifications of sandstone-type uranium deposits which will be the minimum that can meet a company's economic requirements for investment. The method interpolates and extrapolates from available cost data for typical mines to provide the costs for a wide range of possible deposits. The range of deposits achieving the company's required discounted cash flow rate of return on investment at an estimated uranium oxide selling price is then calculated, thus giving the complete range of deposits which meet the minimum required specifications. Prospects are then evaluated by comparison with these minimum requirements.

Jan 1, 1979

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By Bobby Michael (Mike) Roberts, G. M. (Mike) Bernard, Ronald R. Kelly

This paper describes Cananea's successful implementation of the world's first mobile high angle conveyor (MHAC™) to achieve multiple-lift stacking of their primary crushed (2,500 mtph) low-grade ore. The mobile high angle conveyor answered Cananea's needs to stack a second lift, 30-meter high, on their Quebalix I pad. The mobile high angle conveyor is a custom unit that was designed by Terra Nova Technologies (TNT) in conjunction with Continental Conveyor and Equipment Company (CCE's 100th HAC). The stacking system expansion project also includes a rail mounted tripper on the existing overland conveyor and a custom designed "corridor conveyor" to build the corridor for the upper mobile HAC tracks and tail of the existing mobile stacking conveyor. Mexicana de Cananea, part of Grupo Mexico, is a large copper producer in Sonora Mexico and has been in operation continuously for over 100 years.

Jan 1, 2002