Search Documents

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By R. Gradnik

The continuous need for infrastructure expansion forces the mining industry to develop underground structures into more sensitive and violent environments. When underground excavation enters into deep and high stress rock conditions, geotechnical designers find themselves faced with the difficult task of selecting a rock support system that will meet today's stringent requirements. Whatever support system is chosen, it is mandatory that potential rock movement be controlled. All this has intensified the development of safety systems and new, unique solutions which can enable construction companies to go both, further and deeper, without reducing the level of safety. To address these needs, Atlas Copco developed the Roofex® bolt, specifically designed to withstand large static and dynamic deformations under prespecified load conditions. The Roofex Rock Bolt acts as stiff support up to a designable load level before the sliding effect of the mechanical frictional system is triggered and allows highly controlled rock mass movement without loosing the support function.

Jan 1, 2011

By Gordon C. ‘Bud’ Presley

The pumice and pumicite review arrived too late for the June issue. Estimated domestic production of pumice and pumicite in 1992 was up compared with 1991, according to US Bureau of Mines statistics. The Bureau estimate of domestic production of 400 kt (440,000 st) for 1991 turned out to be 401 kt (442,000 st) of actual production, the lowest since 1989. In 1992, the estimated the value of pumice and pumicite sold or used in the United States was $11.6 million, up only $200,000 from the 1991 value. There was an increase in the mine, or mill, average price from the five-year low of $11.44/t ($10.37/st) in 1986 to $26.42/t ($23.96/st) in 1992. Estimated tonnage produced in 1992 was 439 kt (484,000 st). Apparent domestic consumption was 642 kt (707,000 st), up 135 kt (149,000 st) from 1991. Imports for consumption were estimated to be 215 kt (237,000 st) last year. Domestic production supplied 68% of the demand in 1992, with net imports supplying the remaining 32%. This compares with domestic production sup¬plying 53% and net imports supplying 47% of the apparent consumption in 1988. Exports were about 900 t/a (1000 stpy) for the period 1984 to 1988. In 1989, exports rose sevenfold to 7 kt (7700 st) and to 20 kt (22,000 st) in 1990. The Bureau of Mines reported that the amount of pumice and pumicite exported in 1992 was 12 kt (13,200 st). It is assumed that these exports were from the Pacific Coast because imports, mainly from Greece, continued to be a market factor on the East Coast and the Gulf Coast States in the United States.

Jan 1, 1993

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By J. J. Gusek, J. T. Gormley, V. Scovazzo

Glenrock, WY is underlain by two abondoned coal mines. Subsidence events have been recorded over the years, with the frequency increasing in recent years. As part of Wyoming's Abondoned Wins Lands Program, investigations including mining history/methods/mappings, subsurface drilling and material site searches were performed. Portions of the mines less than eighty feet from the surface, were identified as probable for subsidence. Subsidence control by hydraulic backfill was selected. Design included search and injection boreholes, water supply from the mines and the slurry mixing, transport and injection system. Injection system performance and backfill success is king monitored during construction.

Jan 1, 1986

By Donald M. Duncan

An acceptable source of concrete aggregate is available in Kansas City in a continuous, medium bedded, slightly dipping limestone unit. Removal is accomplished in shallow depth, 12 feet to 17 feet high, room and pillar mines. The accepted empirical design spaces 20 foot pillars 60 feet on center. A portion of the 20 foot unit is left in place for roof support. Rock and soil cover is variable to 100± feet maximum. Long-term stability of these mines is affected by numerous factors, including the above mine-rock profile, ground water conditions and mining practice. Crusher-run aggregate sells at the mine for $2.20 per ton, yielding a gross income of $2.00 to $2.80 per square foot of mine. Use of mine space for real estate development requires a new perspective in mine development. Mining practices to obtain long term stabile structures can become an over-riding factor as compared with minimum production costs and maximum extraction ratios. Poorly mined areas are unusuable for secondary purposes. Development cost for lease space in less desirable mines is substantially greater than those planned for a secondary use. Real estate development in mine space involves unique engineering problems. Properly engineered developments offer singular advantages. Warehouse lease space sells for $.50 to $1.00 per square foot per year; fully developed office areas may double these values.

Jan 1, 1968

By James P. Cooney

What is required for the mining industry to grow and prosper in a politically challenging world? The answer to this can be summarized as “the industry’s three priorities.” The first priority is gaining access to the world’s mineralized jurisdictions. The second is establishing a measure of security and predictability in government treatment of mining. Confidence in the stability of the fiscal and legal framework within which mining operates is necessary to encourage the investment of large amounts of capital in mine development. The third priority is sustaining the industry’s welcome during the long term in those jurisdictions worthy of investment.

Jan 1, 1996

By William L. Carter

Through your presence here this morning and your membership in the Society of Mining Engineers, you have shown that you are interested in keeping abreast of the latest technology and mining procedures, want to be part of the continuing progress made by those in your profession, and are looking for ways to participate in expanding your professional and personal experiences and skills. All of these factors are part of your continuing education, the need for peer identification or recognition, and the desire to make a specific contribution to strengthening your profession. However, you may be here with or without your company support and financial backing, unless you are self-employed. Whether you are here for the above reasons, or for many others, your presence reflects a recognition of the importance of participating in the organizational structure of your profession.

Jan 1, 1981

By Carl Rampacek

Laboratory and small-scale continuous pilot-plant investigations made at the Tucson Metallurgy Research Laboratory of the Bureau of Mines have demonstrated that the copper segregation process is applicable to the treatment of oxidized and mixed oxide-sulfide copper ores regardless of the gangue constituents. The process comprises heating the ore to a temperature of 750° C. with small quantities- of sodim chloride and coke to produce metallic copper, which then is recovered by flotation. Tests were made on' 23 copper ores of different types containing 0.8 to 5 percent Cu, .The copper recoveries ranged from 73 to 96 percent in concentrates assaying 10 to 62 percent Cu, depending on the grade and type of ore, The direct operating cost for a 1,000-ton-per-day furnace and flotation plant is estimated at about- $3 per ton of ore.

Jan 1, 1960

By Thomas J. Wright

The evaluation and development of the Eastern North Carolina phosphate deposit resulted in one of the world's largest and most modern phosphate mines and fertilizer complexes at an investment in excess of $90,000,000. The resulting ore beneficiation process showed excellent correlation with pilot plant data. A number of variations from current industrial practices were introduced and projected from bench scale tests through pilot plant to production. Principal among these variations were the following: 1) removal of magnesium by classification, 2) simultaneous flotation of coarse and fine phosphate, 3) the use of saponified fatty acid, 4) utilization of filter wash water for deoiling, 5) utilization of a rougher concentrate for acidulation, 6) calcination of flotation concentrates, and 7) elimination of grinding prior to the manufacture of phosphoric acid.

Jan 1, 1971

By H. J. Hutson

BRS, Inc. has utilized Carlson's Natural RegradeTM software to design the reclamation and stabilization of abandoned open pit uranium mine spoils, AML Project 16N, located in the Gas Hills Uranium District in central Wyoming. This work was completed for the State of Wyoming's Abandoned Mine Land Program (AML) on preSMCRA (Surface Mining Reclamation and Control Act) sites for which no reclamation obligation existed. The project successfully stabilized an eroding spoil dump, enhanced the local view shed, created habitat diversity and provided a significant source of fill material for open pit highwall hazard mitigation efforts. Additionally, the project served to evaluate innovative reclamation design methods, engineering software and grade control technology. This project was nominated for a National Association of Abandoned Mine Land Programs award by the State of Wyoming. The results of this project will be presented as a case history of the Natural RegradeTM approach to surface mine reclamation. Based on the successful application of this new mine reclamation technology on the AML 16N Project, reclamation designs for spoils associated with planned underground uranium mine operations at the Velvet Mine in the Lisbon Valley Uranium District of Utah for Uranium One USA, Inc have been prepared and will be presented. Critical elements will be the encapsulation of unsuitable materials, long term hydrologic stability, and sequencing and staging of ore and mine waste for final reclamation surface construction. The goal of the Uranium One Velvet Project will be to apply best available technology to reclamation planning and fully integrate the reclamation design with the mine planning. Benefits of the approach should include improved public and regulatory perception of the project, facilitate mine permit approvals and the eventual timely release of reclamation bonds, as it is anticipated the stable landform created through this process will result in more rapid stabilization of the site to pre-mine geomorphic conditions. NATURAL REGRADETM CASE STUDY AML Project 16N, D-9 and K Pit Reclamation Project, is located in an intensely disturbed area of the West Gas Hills Uranium Mining District in Fremont County, Wyoming. The overall design calls for the placement of approximately 7 million cubic yards of backfill materials in the D9 and K Pits, imported from adjacent mine spoils including the Central Spoils, and from local highwall excavation. Figure 1 shows the location of the Central Spoils excavation area, as well as the D9 and K Pits fill area. The entire project is located on public lands administered by the Bureau of Land Management, Lander, Wyoming District Office. No access controls are in place at the abandoned mine sites. The public lands are administered under a multiple use land policy including grazing of range land, public recreation, active mining and exploration, and oil and gas. The project site is located along Fremont County Road No. 5, which is a moderately well traveled road. Reclamation of the numerous and large abandoned open pits in the Gas Hills Uranium District has reduced the risk of death or injury to the public. Site History and Background The Gas Hills Uranium District was mined by multiple companies during the period from 1955 to 1981. The uranium was hosted in the Wind River formation, a sequence of soft sedimentary layers of interbedded sandstone, clayey shales, and conglomerates. Uranium was precipitated out of ground water in classic roll front deposits, which are found from very near surface to depths greater than 400 feet. Prior to the enactment of the Surface Mining Control and Reclamation Act of 1977 (SMCRA), very little reclamation work was performed when mines were abandoned or closed. The State of Wyoming Abandoned Mine Lands Program has worked to mitigate hazards associated with large open pits, control migration of unsuitable materials and restore watershed functionality of lands in the district. Additional reclamation is being performed by mining companies on bonded lands. Figure 2, Gas Hills Uranium District aerial photograph, shows the extent of the mining disturbance in the district. [ ] Project Hazards and Concerns The purpose of AML Project 16N is to mitigate hazardous conditions and risk to the public associated with open pit highwalls and toxic, acid forming, and /or radioactive mine waste materials. The D9 and K Pits are contiguous open pits characterized by an 8,800 foot long hazardous highwall that averages over 200 feet tall. In addition to the physical hazard presented by the highwall, the project addresses

Jan 1, 2009

By Arthur B. Cummins

It is appropriate to discuss diatomite at an AIME meeting in San Francisco. California has led the nation, and the world, in the production of diatomite products for more than 40 years. It appears that our State will maintain this position for a long time to come. Diatomite today ranks high in the list of California mineral commodities, with a total value since 1889 well in excess of $100 million. California's production has more than doubled since 1942. In 1959, the value of diatomite production in California is exceeded only by the following industrial mineral materials-borates, stone, sand and gravel and cement20,28. Also, not unimportant is the production of diatomite in each of our other Pacific Coast States, including Nevada. First, let us define diatomite. It is a sedimentary siliceous rock of organic origin, which consists mainly of the fossilized remains of diatoms. Diatoms are microscopic aquatic plants which have the capacity of precipitating silica bio-chemically so as to form a part of their organized structure. In the economic sense, we are not concerned with the numerous types of sedimentary materials which contain minor amounts of diatom residues, or with impure or highly indurated siliceous materials, which may have been formed from diatomite2. Diatomite (synonyms--diatomaceous earth, kieselgurO is a term generally restricted to material of such qualities as to be suitable for commercial uses. Diatomaceous silica is a designation which is best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself, and which is the major' constituent of beneficiated diatomite or processed diatomaceous products.

Jan 1, 1959

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

By T. Umadevi, A. Pratap Singh, R. Sah, K. Abhishek

"It was possible to beneficiate a low-grade iron ore fines sample from Bellary-Hospet, Karnataka, India assaying 56% Fe, 9.1% SiO2 and 5.2% Al2O3 and produce two concentrates, namely, a sinter-grade fines concentrate (43.7% by weight), assaying 63.6% Fe, 2.6% SiO2 and 1.7% Al2O3, and a pellet-grade concentrate (30.7% by weight) assaying 64.7% Fe, 2.9% SiO2 and 1.7%Al2O3. Rejects (25.6% by weight) assayed 32.5% Fe, 27.9% SiO2 and 15.4% Al2O3. The mineralogical characterization indicated that the sample consisted of 69.5% ironbearing minerals (56% hematite, 7.5% martite and 6% goethite-limonite), 12.5% quartz and 15.2% clay, and the rest were minor minerals. Liberation size was found to be in the size range of 25 to 100 µm. The process flow sheet consists of jigs, spirals, grinding and low- and high-intensity magnetic separation of the deslimed feed. IntroductionJSW Steel Ltd is a 10-Mt/a integrated steel plant. To produce 10 Mt/a hot metal requires nearly 16 to 20 Mt/a iron ore fines. The fast depletion of highgrade iron ore fines, increased industrial demand and an increase in iron ore prices have necessitated the exploitation and use of low-grade iron ore fines in the steel-making process after beneficiation. Thus, the beneficiation of low-grade iron ores by removing the associated gangue minerals and enhancing their grade is essential. The use of these iron ore fines in sinter and pellet making has prompted the undertaking of systematic studies on low-grade iron ores.Finely disseminated low-grade iron ores with siliceous impurities have been upgraded by gravity, magnetic and flotation-based processes (Burt, 1994; Svoboda, 1987; Houot, 1983). The processing of low-grade Indian hematite ore containing high levels of alumina-bearing minerals as impurities present separation challenges and pose special problems in martite and magnetite, in association with quartz and clay as the gangue-forming minerals. Alumina is mainly contributed by clay (kaolinite, montmorillonite, illite, alunite), lateritic material and gibbsite; some alumina occurs as solids in iron oxide minerals, namely, goethite and limonite. Silica is mainly contributed by quartz and the associated clay. achieving a high-grade concentrate (Pradip, 1994; Singh and Mehrotra, 2007). Hematite ore basically consists of varying amounts of hematite, goethite,"

Jan 1, 2015

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By J. M. Mutmansky

This paper outlines the results of a study of opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the sixty-seven responses received, about half were from mining engineers and half from environmental engineers. The results of the survey are outlined in detail. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2001

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966