Search Documents

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By Scott Ellenbecker

Soon New York City will have a new train station. A tunnel project is under construction to extend Line 7 to a new station that is located near the Jacob K. Javits Con-vention Center. This is also part of the Hudson Yards redevelopment project that is intended to aid redevelop-ment of the west side of Midtown Manhattan around the Long Island Railroad?s Caemmerer Railyard. The station, or ?cavern? as it?s called by those excavating it, will be the portal for that growth. In the city, public transportation means high-rise residential proper-ties will have better access to the business district, and those outside the area will have greater access to event facilities ? two factors that are critical for development investment.

Jan 3, 2010

By Morteza Gharouni Nik

Flexible Dilatometer Test (FDT) is one of the in-situ test methods for determining the deformational characteristics of rock masses. In this study, several dilatometer tests have been conducted in different geotechnical phases of site investigations by means of two types of FDTs. The purpose of this paper is comparison of the performance of these two types of dilatometers and analysis of the differences in the results of the tests.

Jan 1, 2008

To build an effective entry roof beam, a roof bolting or supporting system must be of the ability of providing a clamping force to the bolted roof strata. Currently, two roof bolting systems are widely used to serve the purpose of providing such a clamping force. They are resin and mechanical anchorage bolting systems. Both numerical modeling and double shear testing results indicate that a greater pre-installed load or pretension of a roof bolting system is very critical for effective beam building. Although it?s generally accepted that a mechanical anchorage bolting system can provide a greater pretension than a resin anchorage bolting system does (Su and Poland, 2007 and Peng, 2008), no published field data are available to support such a conclusion. This paper analyzes the results of our field tests on both roof bolting systems, explains why one roof bolting system is better than the other under a typical roof condition, and finally discusses the effective means for coal mine operators to determine the best roof bolting system for their roof conditions.

Jan 1, 2011

By Chunhui Zhang, Enton Bedini, Jiang Chen, Fengchao Yang, Hang Dong, Xiaoyan Chen

The alteration formed by the reaction of ore-bearing fluid and wall rock is often used as an important prospecting indicator, resulting in the dilution or enrichment of metals or related trace elements. A variety of rock-forming and metallogenic elements have been analyzed in regional stream sediments so that the relationship between the ore-bearing altered rock and the change in the geochemical elemental content can be obtained. Therefore, by using appropriate models, such as matched filtering, the abundance of the distribution of wall rock alteration, similar to the discovered deposits, can be modeled by using the distribution of geochemical elements in the region, and the areas with high distribution abundances are usually favorable prospecting targets. The alteration types related to gold mineralization in the Baiyun gold deposit are potassium feldspar alteration, silicification, pyritization, sericitization, and chloritization. In this paper, the geochemical data of the Qingchengzi ore field (1:200,000 and 1:50,000) have been used to form geochemical images through rasterization. In the three sections of the Baiyun gold deposit, binary-coded curves have been formed, revealing the differences in geochemical elements in stream sediments between altered rocks and the rocks surrounding the Baiyun gold mine. Among them, Au, W, and Mo are enriched elements, while Sn, Zn, and Hg are depleted elements. Several gold deposits are found in the predicted altered rock area by using the matched filtering method during fieldwork, which shows the effectiveness of the method.

Dec 30, 2023

By A. W. Popp

After forty years of exploration and development, the heavy mineral sand deposits of the Murray Basin are on the eve of substantial exploitation by Iluka Resources Limited, Southern Titanium NL and RZM/Cable/Bemax, whom plan to initiate mining and processing operations in 2005. A trial mining and processing operation was undertaken on the Wemen North strandline deposit in 2001-2003 by Murray Basin Titanium, a joint venture of Sons of Gwalia and RZM/Cable, which brought to light a number of mining and processing problems which have since been the subject of extensive studies and process development work. The mineralogy of these weathered strandline deposits is complex by industry standards due to the variety of the heavy minerals present, coatings on the mineral grains and the extensive weathering and alteration which has taken place during the past 50 million years. This paper provides an overview of the complex mineralogy that, in turn, dictates the processes that can be used to recover the valuable heavy minerals. The Murray Basin encompasses some 300,000 km2 and has been a depositional basin, often land locked, since the start of the Cenezoic Era. The economic heavy minerals include ilmenite, altered ilmenite, leucoxene of highly variable composition, rutile, and zircon. There are also other heavy minerals present such as cassiterite, chromite, and monazite in quantities that pose both problems and opportunities. The clay content and overburden thickness also play a major role in the selection of the deposits to be mined. Project Services Consultants (PSC) has undertaken the preparation of this paper as part of its ongoing participation in the mineral sands industry and in particular the project development activities in the Murray Basin region currently being undertaken by Iluka Resources. PSC has been involved with the mineral sands business for several years with senior staff having in excess of 30 years global industry experience. The company is well placed to provide a range of services to clients like Iluka Resources in the areas of project development, execution and strategic development and industry advice.

Jan 1, 2005

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By Nick Rose, Robert Sharon, Mark Rantapaa

Development of the Northeast Layback of Barrick’s Betze-Post open pit commenced in June 2000 and was successfully completed to a height of 400m (1,300 ft) in January 2003. Following a brief exploration drilling campaign at the toe of the final slope, in-pit waste rock backfilling commenced, which will ultimately buttress the final wall. Instability initially occurred in late 2000, above the 5040 Level, as the slope height approached 120m (400 ft). As mining reached the 4680 Level, significant deformation was experienced over a slope height of 230m (760 ft). Slope stability was managed and targeted reserve recovery was achieved by executing complicated modifications of the mine plan, including splitting layback development, well placed offloading cuts, step-outs and mid-slope waste rock buttresses. Decision on timing of these modifying events was often dictated by review of deformation magnitudes and rates determined from continuous slope monitoring records. Design modifications were developed through continuing interpretive refinement of structural geology controls and groundwater distribution, and through stability re-assessments. This document presents an overview of the geological setting and material and strength conditions of the northeast sector of the Betze-Post open pit, followed by development experience leading to design and development of the Northeast Layback. Rock mechanics modeling, design details and geotechnical performance monitoring are then presented. Development experience, stabilizing adjustments to the original design and safety procedures for development and exploration activities are described. The document is finalized with conclusions and acknowledgements.

Jan 1, 2005

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

By J. A. Botín

NPV is a static measure of project value which does not discriminate between levels of internal and external risk in project valuation. Due to current investment project?s characteristics, a much more complex model is needed: one that includes the value of flexibility and the different risk levels associated with variables subject to uncertainty (price, costs, exchange rates, grade and tonnage of the deposits, cut off grade, among many others). Few of these variables present any correlation or can be treated uniformly. In this context, Real Option Valuation (ROV) arose more than a decade ago, as a mainly theoretical model with the potential for simultaneous calculation of the risk associated with such variables. This paper reviews the literature regarding the application of Real Options Valuation in mining, noting the prior focus on external risks, and presents a case study where ROV is applied to quantify risk associated to mine planning.

Jan 1, 2012

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By Gökhan Çevikbilen, Ümit Karadoğan, Sevde Korkut, Berrak Teymur

This study proposes a methodology for dewatering of mine waste using a multistage process, combining geotextile tubes and anionic polyacrylamide (PAM), which accelerates the recycling process of water for aggregate mine waste facilities. For this purpose, waste from a rock quarry located in Istanbul was investigated. Flocculation tests revealed that the use of anionic PAM at an optimum dosage reduced sedimentation time and decreased turbidity. The compatibility of geotextiles and mine waste conditioned with different dosages of the effective PAM was evaluated by rapid dewatering tests, considering the water content of the filter cake, amount of infiltrated solid content, and rate of filtration. Geotextile dewatering tests were also performed on PAM-free and conditioned suspensions. The dewatering process was optimized by the use of a geotextile tube in two stages: (i) on the unconditioned suspension and (ii) on recovered PAM-conditioned leachate. Directing PAM-free non-hazardous soil-based material obtained in stage i to alternative beneficial uses is suggested, to minimize the volume of waste. Furthermore, recycling of the effluent obtained at the second stage of the proposed method will ensure more efficient water reuse

Sep 29, 2022

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Jiayao Wang, Jian Chen, Leiting Shen, Hongyang Wang, Zeping Cao, Ziru Wang

Large amounts of by-products, including coal gangue, circulating fluidized bed (CFB) slag, and coal fly ash (CFA), are generated during mining, washing and burning of high alumina coal (HAC). The stockpile of these by-products of HAC will cause the pollution of air, water and soil. Meanwhile, the unbalanced regional distribution of bauxite and alumina production has been a critical challenge for the sustainability of world alumina refineries, especially for China. Therefore, economical extraction of alumina from by-products of HAC not only resolves the environmental pollution problems caused by stockpile but also decreases the dependence degree of import bauxite in China. Considering the fact that powder alumina can only be produced by alkali methods, the alkali extraction of alumina from by-products of HAC is summarized in this paper. Based on the formation process of by-products of HAC, the principle, research status, and problem of existing methods were analyzed and discussed, as well as the forecast of research trend. The analyses indicate that simplex recovery of alumina from byproducts of HAC generates large amounts of leaching residue (red mud) with difficulty for disposing, while comprehensive extraction of alumina and silica meets the research trend for clean and high-value utilization.

Aug 25, 2023

By F. L. Pirkle, D. L. Pirkle, E. C. Pirkle, W. A. Pirkle

Heavy minerals have been mined from the sands of the United States’ Atlantic Coastal Plain since the early part of the twentieth century. Production of ilmenite from beach sands near Mineral City (Ponte Vedra), Florida, began in 1916. The first reported large-scale recovery of zircon in Florida was reported from this deposit in 1922 and of rutile in 1925. These operations ceased in 1929. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site. In 1942 heavy-mineral operations were established on 202 hectares of land situated in Duval County, Florida. The location is about 16 kilometers east of the center of Jacksonville, Florida, in an area known as Arlington. This operation demonstrated that low-grade sand containing only 2 to 3 percent titanium minerals could be concentrated economically with the Humphreys spiral and that the oxides could be separated from the heavy silicates by electrostatic methods. Much of this area is now covered by a large mall and is a major retail- commercial center. Between 1958 and 1964 the Skinner tract, a deposit about 4 kilometers south of the above deposit, was mined. Today the area of this deposit is known as Deerwood, a gated country club community on the southside of Jacksonville. Further inland, E.I. du Pont de Nemours and Co. has been mining heavy minerals from a physiographic feature known as Trail Ridge since 1948, and a deposit near Green Cove Springs, Florida has been in production since 1972. Since the start of heavy-mineral mining in the southeastern United States, nine heavy-mineral ore bodies either have been or are being exploited in Florida and Georgia. Other deposits either have been lost to mining or are yet to be mined. These deposits have different origins. Some formed along shorelines at the heights of marine transgressions while others formed on regressional beach ridge plains during periods of temporary stillstands or slight transgressions. These different origins are reflected in the chemical and physical characteristics of the deposits. Ilmenite in older, more western deposits has a higher TiO2 content than ilmenite in younger, more eastern deposits. TiO2 content does not very with north-south direction. Garnet and epidote are absent or rare in the older Trail Ridge deposits, but progressively become common in the younger Duval Upland, Crestal Pamlico, and Holocene deposits. Grain size is coarsest for Trail Ridge sediments and finest for sediments in Duval Upland and Crestal Pamlico deposits. The average grain size for Holocene deposits is intermediate between Trail Ridge and Duval Upland deposits. The two models for the origin of the heavy-mineral deposits – deposits formed at the height of major marine transgression; and deposits formed during periods of temporary stillstands or slight transgressions that occur during a general marine regression; - are consistent with known sedimentological data and depositional trends.

Jan 1, 2005