Search Documents

By Steven W. Hunt, Safdar A. Gill

Design and construction of temporary shafts for underground facilities often require evaluation of bottom stability due to rupture (blow-ins) caused by water pressure acting on a bottom plug. This paper provides an overview of shaft bottom stability evaluation methods for the case of a relatively watertight soil plug which overlies an artesian aquifer. Methods of considering plug perimeter shear, plug buckling and pressure relief are discussed. Minimum factors of safety are suggested. Future use of the shaft subgrade is also considered. Bottom plug failure case histories at several shafts are evaluated. This paper should be useful to project designers, ground support system design engineers and contractors involved with construction of shafts for underground facilities

Jan 1, 1997

By Jeff Poe

When a takeup weight is offset to the side of a conveyor, a wire rope is commonly routed from the takeup weight through a series of sheaves to the takeup carriage. The friction developed from a series of wire rope sheaves can effect the actual belt tension at the make up carriage. Through real-mime testing the actual tension on a makeup carriage was recorded with data acquisition using an internally strain-gauged turnbuckle. The wire rope used to transfer the makeup weight to the makeup carriage was routed through a series of lubricated bronzed bushed sheaves. The tension on the makeup carriage was found to be as much as 26% higher than the weight of the makeup due to the friction in the sheaves. A detailed discussion of the testing and results will be made.

Jan 1, 2000

By D. D. Runnells, G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two of the pit lakes, 26- and 55-m (85and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper pit lakes, 110- and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1998

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009

By H. Wagner

Recently a detailed study ?Minerals Planning Policies and Supply Practices in Europe? has been completed. The study, conducted on behalf of DG Enterprise, demonstrated that there are very few written down national minerals policies within European Union. Mineral policy elements are dispersed in many different documents and acts. The paper discusses the essential elements of minerals policies; particularly importance is placed in issues related to planning (land use planning, mineral development, etc.). A number of examples of successful and less successful mineral planning policy approaches are presented in other to support the idea of importance of comprehensive mineral policy. The main sources of information were the country reports of 26 European countries that are appendix of the study. We conclude that comprehensive written mineral policy that incorporates essential elements is crucial in order to achieve secure minerals supply.

Jan 1, 2007

By Beth Robinson

This first of two articles on the Second Mexican Mining Rail Excursion describes some of the more casual experiences participants enjoyed on last fall’s rail tour of major Mexican mining operations. In this article, Beth Robinson, a graduate student at Colorado School of Mines, describes trip organizers, participants, and some of the unique events occurring during the two-week excursion. Next month, part two of the series will highlight various Mexican mines and plants.

Jan 1, 1982

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

By J. Burgess Winter

It is an honor to present the lecture in honor of Daniel C. Jackling, the developer of the technology of copper mining that we continue to use 100 years later. He made a dramatic breakthrough in the early part of this century in the development of bulk-mining methods for large, low-grade porphyry copper-sulfide ore bodies. At Magma Copper, we are particularly proud that the Jackling Award states we have "made significant contributions to technical progress." Before Jackling's time, copper mining had exploited with primitive equipment very high-grade underground ore bodies and high-grade open pits. During the 20th century, the situation changed. Three significant innovations occurred within about 10 years around the turn of the century. In 1903, Jackling's concept of large-scale mining with steam shovels and rail haulage was implemented at the Bingham Canyon mine in Utah. Eighty years after the introduction of rail haulage, the mine converted to truck haulage with large-capacity high-efficiency haul trucks and reduced the stripping ratio from 3.5:1 to less than 1:1.

Jan 1, 1995

At present, discounted cash flow analysis is generally accepted as the preferred method of valuation of mine projects in surface coal mining. One of the major reasons for that is its ability to take into account the time effect of money over the life-of-mine. As a looking-forward method, it requires forecasts be made with regard to economic, technological, technical, geological, and environmental conditions that will prevail in the future. All forecasts are inherently uncertain as they are a function of the uncertainty of all variables of the discounted cash flows analysis. This indicates that the only alternative for modeling the uncertainty in the project evaluation is the development of adequate risk models to serve the decision-making process. The paper offers a model of project cash flows at risk in strip coal mining, which is an integrated corporate risk management solution. The model is based on a stochastic approach that provides the answer to the question about how large is the deviation between stochastic cash flows and the planned value (or that used in the budget) at each time step of the discounted cash flows analysis, that is due to the uncertainty in the model variables. A solution is worked out for the allowable range of the stochastic cash flows variation that determines the probability of achieving the planned value of a mine project. The Monte Carlo simulation technique is used to model the stochastic behavior of the project variables. A case study of an opencast coal mine project is provided to illustrate the applicability of the risk model. The results obtained provide a new understanding of the mine project risk as a component of the project discount rate.

Jan 1, 2006

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. They are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations.Cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance of having proper stability in cyclone operation while implementing any plant-wide optimization strategy.One of the key challenges in cyclone operation is that cyclones are highly sensitive to changes in operating conditions and are affected by process fluctuations such as feed pressure, solids concentration and flow rates. Fluctuations in cyclone feed characteristics lead to unstable cyclone performance which affects mineral liberation. For such an impactful unit operation, cyclones have historically been under-instrumented in an otherwise highly instrumented process plant. Traditionally, mill operators have relied on visual observations of the apex discharge to determine the operating state of the cyclones. Visual cues corresponding to the different cyclone operating conditions have been discussed by Neesse et al. (2004) as shown in Fig. 1."

Jan 1, 2014

By Dan Armour

Bolting solutions traditionally offered only wet drilling or dry drilling options; each with advantages and disadvantages. Joy Mining Machinery has developed a Mist Drilling System that incorporates the best of both types of drilling. Compared to wet drilling, mist drilling offers as much as a 90% reduction in water use. As a result, floor and roof conditions are tremendously improved. This offers a safer and more comfortable work environment for operators. Mist drilling can offer a significant reduction in noise levels compared to dry drilling and in recent trials, bit life has been greatly improved. Holes are cleaner and operators experience less exposure to respirable dust.

Jan 1, 2005

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

By T. Patten

Inter-Mountain Labs, IML, performed a study comparing mining waste rock sample analysis by Net Carbonate Value (NCV) and Modified Sobek acid-base accounting procedures. The study looked at 468 waste rock samples and compared the data for Neutralization Potential (NP), Acid Generation Potential (AGP), Net Neutralization Potential (NNP), and the ratio of NP/AGP. The study found that a majority of the samples were below 50 Tons CaCO3/kTons. This subset of ?low-level? samples was also examined separately for Acid Base Accounting parameters. The analysis compared the NCV procedures to the Modified Sobek procedures and concludes that the NCV procedures are as protective of the environment as Modified Sobek procedures.

Feb 27, 2013

By S. Möllerherm, E. Drüppel

"The development of indicators to assess the sustainability of mineral raw materials operations is amajor task with respect to its actuality and difficulty. This holds true even more when dealing withenvironmental indicators.The use of existing environmental indicators in the mineral raw materials industry leads to false orat least distorted results. Therefore the Institute of Mining Engineering I from the RWTH AachenUniversity developed indicators and an assessment system for the mineral raw materials industryon operation, company and sector level on behalf of the Federal Ministry of Economics and Labour(Bundesministerium für Wirtschaft und Arbeit, BMWA) and the Federal Institute for Geosciencesand Natural Resources (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR).In total 30 indicators were defined and designed to assess the performance of the mineral rawmaterials industry in terms of sustainable development, 10 indicators for each pillar (economical,ecological and social pillar).The following paper describes some of the results focussing on the development of environmentalindicators. These had to be adapted or completely new designed in order to match the specificcharacteristics of the mineral raw materials industry."

Jan 1, 2005

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977