Search Documents

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By Ulf G. Gwildis

The Bright water Conveyance System includes 21 km of tunnels mined by two earth pressure balance Tunnel Boring Machines (TBMs) and two slurry TBMs. The probabilistic baseline approach defined in the Geotechnical Baseline Report (GBR) can representatively be verified by use of a comprehensive tracking system to identify face conditions that allows comparison with the baselines. The glacial geology includes a high lateral variation in soil types that, when combined with the pressurized face tunneling methods, creates challenges for documenting face conditions. Baseline tracking using spoil samples and TBM operational parameters provides information to document actual conditions and support resolution of differing site condition claims.

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By Tim O’Neil

Question: Looking forward, do we face a future in which energy markets, energy policy and energy conflicts threaten to preoccupy, if not dominate, our concerns over economic growth, national security and domestic tranquility? The answer is, we may indeed face such a future. Question: What oil resource is comparable in size to the reserves of Saudi Arabia and presents a tremendous opportunity? The answer, the oil sands in Alberta, Canada. Question: What is the largest mineral staking rush in North American history, still under way? It has so far led to the development of two large mines. The answer is the Point Lake diamond strike in Canada’s Northwest Territories. It led to the development of the Ekati and Diavik mines.

Jan 1, 2004

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By A. D. Davis

The Gilt Edge Superfund Site is a former heap-leach gold mine that currently is being remediated in the Black Hills of South Dakota. Mine runoff water is treated before release from the site. The field pH, before treatment, is about 3, and the water contains arsenic and some heavy metals, in addition to sulfate concentrations of about 1400 to 1500 mg/L. In the Keystone area of the Black Hills, naturally occurring arsenic has been detected in ground-water samples from wells. Keystone City Well #4, which is not used currently, showed arsenic concentrations of 36 parts per billion (ppb) and sulfate concentrations of about 19 mg/L. With field samples of water from these sites, a limestone-based method was successful in reducing arsenic and heavy metals concentrations. The results are significant because previous research with the limestone-based method mainly had involved samples prepared with distilled water in the laboratory, in which interference of other ions such as sulfate did not occur. The research indicates the potential for broader field applications of the limestone-based removal method.

Jan 1, 2011

By Steve Skelhorn

Over the recent years, major advances have been made in design of precast concrete segmental tunnel liner. Starting from basic, parallel sided rings, we now have state of the art, universal rings incorporating custom tapers to suit individual requirements. At planning stage, the ring diameter is normally fixed and the ring geometry is one of the first items to be assessed. Obvious factors such as TBM layout and curve radius can constrain geometry; however, there others factors that should be considered in order to optimize production. This paper takes a look at the history of the segmental rings and criteria for ring selection, including: general ring geometry;; individual segment geometry; ring taper, and ring width. This paper also explores optimization of ring with a focus on constructability.

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By Chee Theng

"Mining professionals are a resilient lot. Sure, copper prices are dismal, permitting processes seem interminable and the top mining companies are shedding jobs like a Shetland sheepdog sheds hair. All the more reason to hone technical skills, reconnect with old contacts and get one’s finger on the pulse of the industry.More than 400 did just that in the balmy sunshine and among the saguaro cactus of the Tucson venue of the SME Arizona Conference.Giving the keynote speech was Patrick Merrin, vice president at Hudbay Minerals (see box), while the luncheon speaker was University Distinguished Professor Mary Poulton, director of the Lowell Institute for Mineral Resources at The University of Arizona.“Attendance was great, especially given the copper price,” said Ta Li, vice president of business development at Tetra Tech and 2001 SME President. “The luncheon speaker was one of the better ones in recent years. Her talk contained a lot of fresh ideas, and practical versus theoretical concepts.”Talk about values, not economicsPraise was unanimous for Poulton, who gave a thought-provoking talk on “The New Face of Mining: The Culture Change for Compatible Mining.” Corporate social responsibility has been embraced by the metals mining industry, and it’s being done right, she said. “So why do we have more conflict? Why are there more protests? Why does permitting take longer and longer?” Poulton made a case for an approach based on compatible, rather than sustainable, mining to present a new face of mining that can be compatible with communities, cultures and the environment, and still be profitable. When the mining industry starts to talk about compatibility between what it is doing and what “me,” as the consumer, wants, what “we,” as citizens of a community, want, and what’s good for the “world,” we’re going to see the next culture change happen, she concluded."

Jan 1, 2015