Search Documents

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By Y. C. Guan

The dissolution behavior of silver and copper form their elemental states and Ag/Cu alloys in ammoniacal solutions has been studied using rotating disc electrodes. The variables studied included concentration of ammonia, oxygen partial pressure and rotating speed of the disc. The results have been interpreted in terms of the mixed potential theory. The effect of local current resistance on the overall current has also been examined as a part of the governing theory of the dissolution. It was observed that the dissolution potential and the rate of dissolution were very much affected by the composition of the alloys.

Jan 1, 1995

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By Richard C. Enochs

In order to clearly understand our process control system it is necessary to briefly discuss the various process control systems that were considered and why we chose our particular configuration. We considered Analog Systems, Computer Supervisory Systems, Computer Setpoint Systems, Direct Digital Systems and Direct Digital with Backup Systems. Our concept of these systems is illustrated in Figure 1 through Figure 5. We chose Direct Digital Control with Manual Backup because it had the greatest flexibility, ease of implementation and cost no more than a pure Analog Control System for one control concept. There would be no increase for a Direct Digital Control with Manual Backup System if the control concept were changed, while there could be considerable additional cost with an Analog System, if the control concept were changed.

Jan 1, 1975

By R. Z. Pyrih

Uranium tailings at Cotter Corporation's Canon City, Colorado Mill were moved to a double-lined impoundment, but uranium and molybdenum salts remaining in the fractured bedrock underlying the old tailings ponds seeped into groundwater. Fluor Daniel GTI recommended an in situ geochemical fixation remedy, flushing Best Sulfur Products' calcium polysulfide reductant into the subsurface with clean water. Residual metals became immobile, trapped in the bedrock. Fluor Daniel GTI designed and implemented the process on ten acres with high metal concentrations. Cotter is operating and monitoring the system, which can be expanded to "hot spots." The original remediation time was estimated at less than five years.

Jan 1, 1998

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

By K. Norris

The Amax Gold Guanaco mine is located in the Atacama Desert, approximately 260 km southeast of Antofagasta, Chile. The 6,000 tpd leach operation produces approximately 90,000 oz of gold, and 360,000 oz of silver per year. Production began in 1987, and the operation has been managed by Amax Gold since 1992. The mine has been plagued in the past by high operating costs and low production. Several significant changes have been made to the operations which have resulted in lower costs and higher operating efficiencies. A review of these changes is presented herein.

Jan 1, 1997

By R. Y. Wan

Recent research efforts have shown have shown selective solvation extraction of a gold cyanide ion-pair complex from alkaline cyanide solution is possible with organic phosphorus esters. These alkyl phosphorus esters such as tributyl phosphate (TBP) and di-n-butyl n-butyl phosphonate (DBBP) can selectively load gold to rather high levels, even in excess of 30 gpl. However, traditional stripping techniques are not particularly effective. In this regard, gold recovery by direct electrolysis of the organic phase has been found to be an interesting possibility. Further, the rate of direct electrodeposition from the organic phase can be improved significantly by using an aqueous/organic mixture. Direct electrodeposition of sheet gold from loaded DBBP was successfully accomplished at a current density of 8x10 4 amp/cm2 and 55°C from such a two-phase mixture with the aqueous phase as the continuous phase. No appreciable degradation the DBBP was found after 5 cycles of extraction and, electrodeposition. Finally, the applicability of the process strategy for an industrial situation was demonstrated by the successful treatment of waste gold cyanide electroplating solutions.

Jan 1, 1986

By Jurgens PE Hamman, Faisal Putra, Hadnaltias Alpeki, Willem de Beer

The Deep Ore Zone mine is the third lift of caving at PT Freeport Indonesia’s East Ertsberg Skarn System. An increasing trend in seismicity along the northern boundary of the DOZ cave, as well as the northern fringes of the DOZ production and infrastructure levels, was taken as indicative of an interaction between the approaching DMLZ cave and the DOZ subsidence zone. Seismicity trends and locations indicated a reducing crown pillar and an associated stress increase along these DOZ excavations, as well as the regional area along the DOZ cave boundaries. Although rockbursts were not identified as an immediate hazard, seismic shakedown was a highly probable hazard in the case of remote large (≥3.0) seismic events. An evaluation process, as described in the Canadian Rockburst Support Handbook (1996), was followed to identify and quantify the various parameters that could contribute to a shakedown evaluation. A shakedown assessment, based on the Peak Particle Velocities scaling relation, was conducted to assess the current installed ground support systems along the northern fringes and the fixed facilities of the DOZ mine. The range in ground support systems were mostly due to different geotechnical environments. The load–deformation characteristics of these support systems were evaluated to determine the support capacity and compared to the potential support demand under varying shakedown conditions. Shakedown hazard maps were compiled to indicate the installed ground support system’s vulnerability to seismic shaking. Based on this information, areas were divided into zones indicating whether they were sufficiently supported, additional support was required, access was to be restricted, and / or they were to be abandoned. Mine management utilised these hazard maps to strategize actions for the various operational zones within the DOZ, including the fixed facilities. This paper briefly describes the derivation of the PPV scaling relationship. Seismic and geological data for the DMLZ – DOZ interaction areas were evaluated to determine the likely source of large events. Subsequent larger events and their effects are shown to assess the veracity of the magnitude and PPV estimates, as well as the effectiveness and appropriateness of the ground support systems.

Apr 26, 2022

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982

By A. Ang-Ug, L. Gurieff

"The Phu Kham Cu-Au mine in Laos is owned and operated by Phu Bia Mining Limited. The deposit is a complex and low grade Cu-Au porphyry ore. The rougher feed has a particle size distribution of 80% passing 110 µm, and the rougher concentrate is reground for cleaning to 80% passing 25 µm. The Cu losses in the cleaning circuit are primarily in the <12 µm fraction. A randomised paired ON-OFF test of magnetic conditioning in one of the two parallel cleaner 1 circuits was undertaken. The results showed that with magnetic conditioning there was approximately a 10% reduction in the <12 µm Cu distribution in the cleaner 1 tail to a 98% level of confidence. The Cu distribution in the <12µm fraction is a less variable measure of changes in the <12µm Cu recovery, therefore, this was used to evaluate the impact of magnetic conditioning. Subsequently, magnetic conditioning was installed in both cleaner 1 circuits and the plant results monitored after this installation. Comparing the plant results immediately before and after this installation showed that there was a 20% reduction in <12µm Cu losses to the cleaner tail. INTRODUCTION The Cu-Au, Phu Kham Mine (PKM) is located within PanAust's Phu Bia Mining Contract Area in Laos, approximately 140 kilometres from the capital city, Vientiane. PKM is PanAust's flagship operation and the significant cash flow generated by PKM has supported PanAust’s growth, while contributing to a strong balance sheet. PKM comprises an open-pit mine and a conventional milling and flotation operation that produces and exports a Cu and precious metals concentrate. The concentrate contains around 23% Cu, 6 ppm Au and up to 35 ppm silver. Process Overview The PKM deposit consists of complex heterogeneous mineralogy horizons of Cu-Au stockwork and skarn mineralisation. It contains areas of soft-leached zones, overlying transition zones and supergene chalcocite dominant secondary Cu mineralisation and clay-rich gangue. Areas of high As and Zn also pose a challenge in treating the highly variable ore. In addition, hardness of the ore increases with deposit depth. The ROM is hauled to a primary gyratory crusher to produce a coarse ore stockpile with size distribution suitable for the 13 MW semi-autogenous mill. The SAG product feeds two parallel ball mills each equipped with a cyclone cluster producing a product particle size distribution of 80% passing 110 µm. The conventional flotation circuit consists of two parallel rougher banks. The rougher concentrates feed the regrind cyclone where the underflow is split and reports to two parallel, 3MW, M10000 IsaMills. The regrind mill discharge combines with the regrind cyclone overflow with a product particle size distribution 80% passing 25 µm and reports to the Jameson cell."

Jan 1, 2018

By Luis Elu, Andy Bolland, Jack Simmons

The gold refinery at Barrick Goldstrike Mines has increased production to more than 2,000,000 ounces poured per year while reducing the labor requirement. Safety and health has not been compromised with this increased production and in fact incident rates and exposures have reduced over the past five years. Streamlining procedures, improving ergonomics and the wise use of unique innovations has accomplished this significant achievement.

Jan 1, 1998

By Neal Rackstraw, Mamo Meaza

Washington Metropolitan Transit Authority Section E8a consists principally of twin tunnels 1,713 meters (5,620 ft) long, excavated to a diameter of 6.35 meters (20.83 ft) using an open face shield, with a primary lining of four unbolted precast concrete segments expanded at the crown, and a full circle unreinforced concrete final lining with a finished tunnel diameter of 5.08 meters (16.67 ft). The tunnels, constructed in Cretaceous age sediments, are mostly in stiff to hard clay except for a few areas along the alignment that contain dense to very dense fine sand in the upper portion of the tunnel that created a mixed face condition. At two locations unexpected heavy water inflows produced very serious problems in both tunnels. Water flows in the interface area were generally more than 378.5 1pm (100 gpm) and reached as high as 2,649.5 1pm (700 gpm) in the mixed face ground. The nature of the tunnel inflows, the consequences, and the corrective measures adopted will be the subject of this paper.

Jan 1, 1991

By Donald E. Ranta

Many portions of the mining industry are under intense pressure to reduce costs while commodity prices languish. In response, global Internet-based marketplaces to deliver business-to-business (B2B) e-commerce solutions are being established to reduce costs and improve efficiencies across the mining industry supply chain as well as with customers. Over time these marketplaces will likely evolve to create an integrated supply chain solution, layer in value-added services, and develop mining community portals with industry content. Significant opportunities to help reduce costs and create value are available in mining e-procurement as well as in on-line product sales. The supply chain for the industry is highly fragmented and many mining companies have numerous inefficiencies in procurement. An e-procurement marketplace (or "exchange") can immediately address these inefficiencies and offer numerous benefits to buyers and suppliers. These benefits include improved sourcing options, inventory cost reduction, transaction cost reduction, access to value-added services, lower customer and supplier acquisition costs, improved reach, and improved information flows.

Jan 1, 2001

By William E. Spence

Gold was discovered at the Haile mine in Lancaster County, South Carolina in 1827 or 1828, and since that time the mine has been worked intermittently by both open pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 ounces. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores.

Jan 1, 1978

By Silvano Perla

Peabody Western Coal Co. operates two mines in northern Arizona. The Black Mesa and Kayenta coal mines are unique for several reasons. They both have only two customers: Southern California Edison’s Mohave generating station near Laughlin, NV and the Navajo generating station near Page, AZ. Both mines are close together. Between the two, they ship nearly 11 Mt/a (12 million stpy) of coal. Material is shipped to the power stations in two ways. This first is a 440- km-long (273-mile-long) underground slurry pipeline, the longest in the world. The second is an 11 -km-long (17-mile- long) long conveyor to four storage silos. Product is then shipped by train from the storage silos to the plant sites. Another factor makes these mines unusual. They are both situated in the middle of the 68,795km2 (17 million- acre) Navajo Reservation, home to the Navajo Nation and Hopi Tribe members. Nearly 90% of the Black Mesa and Kayentamines’ 850 employees are tribe members. Peabody Western Coal is the United States’ largest private employer of Native Americans.

Jan 1, 1995

By A. LaPlante, A. Cauchon

This gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18130 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size- by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 pm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution, generated by intensive column cyanidation.

Jan 1, 1990