Search Documents

By S. M. Jarrett, W. B. Schmidt

Within the last year, the Nation has been shocked by two major tunneling disasters. Almost exactly a year ago 17 men died in the San Fernando Tunnel in an explosion attributed to gas. A few months later another 21 men died in an explosion laid to the same cause at Port Huron, Michigan. The analysis of the causes of these accidents is still continuing. While it appears that they differ substantially from each other in their specifics, they share the common trait that, like most industrial accidents, they might well have been prevented. Gas explosions in tunneling are neither new nor particularly unusual. Forty years ago, Assistant Director Jarrett was hired as a safety engineer on the Hetch Hetchy Aqueduct in California after an explosion that killed 12 men. Prior to 1946, in California alone, the Bureau of Mines had recorded 27 gas explosions incidental to hard rock mining and tunneling. The purpose of this paper is to review the status of the principal regulations affecting tunneling and to indicate some ways in which safer and more healthful conditions can be obtained. The Bureau of Mines was established by an Act of Congress of May 16, 1910. Since that time the Bureau has been making investigations and compiling and publishing health and safety data relating to mining and to tunneling. If any benefit is to come from an anaylsis of tunneling accidents, it must be the knowledge needed to prevent their repetition. The Bureau of Mines has also had informal discussions with the Department of Labor regarding the possibility of the Bureau's assuming that agency's responsibility for tunnel inspections.

Jan 1, 1997

By A. S. Kastrinos

There are many concepts of preventative maintenance. The basic objective of all maintenance organization, however, is the efficient (accomplishment and control of all) inspection, repair, overhaul, material and preventative maintenance functions necessary to maintain facilities and equipment in a condition that will meet operating requirements at a level consistent with low costs and high availability. To formulate a preventative maintenance program requires sound judgment and the ability to apply in a practical manner a system that meets Plant operation requirements, based upon organization, experience, conditions, design and historical data. A maintenance program must be divided into to categories consisting of: 1. Scheduled tasks to be accomplished at planned intervals. The objective of these tasks is to maintain reliability and prevent as much as possible abnormal failures. 2. Non-scheduled tasks that result from periodic reports and which can be scheduled to fit in conveniently with other routine work. The non-scheduled work items may include long-range preparation for lenghty shutdowns requiring Engineering and Shop services.

Jan 1, 1975

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By Aydin Shaterpour Mamaghani, Cemal Balci, Nuh Bilgin, Mucahit Namli, Hanifi Copur

"It is expected that more than 10 Billion USD will be spent in Istanbul in coming years on tunnel boring especially with EPB-TBMs. However, the geology of Istanbul is very complex. Geologic formations changing from Paleozoic to Cenozoic ages cause tremendous problems due to frequently changed rock formations and andesite and diabase dykes. This paper summarizes a universal model to predict the performance of EPB-TBMs which is created upon the data base collected from several projects. The model first is based on predicting field specific energy and power consumed of TBMs using geo-mechanical properties of the excavated material and TBM diameter. Later net production rate is calculated using field specific energy and power consumed by TBM. A methodology to predict machine utilization factor permits to calculate daily advance rates. The validity of the model is tested using the data obtained from two recent metro tunnel projects. 1. INTRODUCTION It is expected that in a near future a total length of 400 km will be excavated in Istanbul in a complex geology. Selecting proper tunneling equipment, organizing an effective operational management with the right tunneling crew will be a major concern for an efficient scheduling of the future projects necessitating to create a model to estimate daily advance rates. Several TBM performance prediction models with few on the prediction of machine utilization time were realized in the past. However, there is quite limited number of research studies on predicting the performance of EPB TBMs. Specially predicting daily advance rates in complex geology, in mixed face, in fractured rocks, in transition zones etc. are in big concern (Namli et al. 2013, 2014). The first experiences in Istanbul with a gripper type TBM was a nightmare, roof collapses caused big delays in tunnel excavation (Bilgin 1993). A typical example to EPB-TBM was Kadikoy-Kozyatagi tunnel, changing TBM from opened mode to closed mode with few modifications on the cutterhead resulted a tremendous increase in the daily advance rates (Bilgin et al. 2009). The data collected from several tunnelling projects served a basis to create a model to predict daily advance rates of EPB TBMs. Within the frame of a research program the validity of the model was tested in Uskudar-Umraniye–Cekmekoy-Sancaktepe metro project and very recently in Mecidiyekoy-Mahmutbey project."

Jan 1, 2016

By R. Buchan

A number of mineral processing techniques have been adopted for the separation of the plastics making up a typical beverage bottle, and a complete flowsheet developed. Thus, size reduction, heavy media separation and flotation were used to separate PE, PVC and PET from their mixtures with cellulose fibers and aluminum, which makes up the cap of such bottles. It is shown that while heavy media separation allows the separation of a PVC/PET mixture from the solid waste, froth flotation can be readily used to separate PVC and PET from a mixture of the two. For this purpose, the differential action of an alkaline aqueous solution (PH=II) which contains methanol and MIBC as surface tension control agents has been found to be a suitable flotation medium. This paper reports some aspects of the flotation flowsheet developed for the separation of plastics from municipal solid waste mixtures and PVC from PET.

Jan 1, 1995

By W. G. Kegel

Coal mining today is confronted with numerous problems, all of which affect in some way the ability of the operator to produce profitably. The major endeavor, therefore, is a quest for cost lowering techniques. Complete belt haulage from shuttle car to river barge appeared to be a step in such a direction. A deep look into all aspects proved this to be more involved than just the installation of such a belt line. With this paper, we will attempt to present to you the problems and requirements of design and installation of an all-belt haulage system, believed to be the longest underground belt installation in the world at this time. The first and most important item is the justification of an all-belt haulage system. The following is a brief history of the coal property and the facts affecting our decision.

Jan 1, 1964

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By S. Mathur

Oxide particles are commonly used as fillers in plastics, paper, rubber etc. (particulate composites). The successful fabrication of such composites is dependent upon the adhesive strength of the filler particles to the matrix. The compatibility of the matrix and the filler particles is generally enhanced by adsorption of surface modifiers such as surfactants and polymers at the particle-matrix interface. In order to develop a scientific basis for selection of appropriate modifiers it is necessary to understand their adsorption mechanism(s). Specifically, adsorption of polymeric additives is attributed to a combination of chemical and electrostatic interactions, hydrogen bonding and van der Waals forces. Hydrogen bonding has been suggested to be the primary adsorption mechanism for non-ionic polymers. However, a literature survey of Poly(ethylene oxide)(PEO)-oxide system suggested PEO, a non-ionic polymer, to be substrate specific. A systematic study was undertaken to investigate the adsorption mechanism(s) of a PEO on oxide particles. It was determined that strong Bronsted acid sites on the surface interact with the ether oxygen, a Lewis base, of PEO to induce adsorption. In this work characterization of PEO binding sites on oxides is reported and the mechanism(s) of PEO adsorption discussed.

Jan 1, 1997

By L. Hales

Neural networks are a generalized, multivariable non-linear modeling technique that can be used to model mineral processing operations. Neural networks will be described as will their use in modeling column flotation. Optimization of column flotation will be explored and discussed by using the neural network column models.

Jan 1, 1996

By D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. Current beneficiation for these ores is almost entirely by flotation. Silver recovery often is low, but little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate collector concentration, conditioning time, potentiostatic control of the mineral potential, and pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling mineral potential during the flotation process is discussed.

Jan 1, 1994

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization's structure that addresses the immediate and long-term impact of a company's products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By Fred C. Wrobbel

Two counties in Illinois, Ope and Hardin, and three counties in Kentucky, Crittenden, Livingston and Caldwell comprise the entire Kentucky-Illinois fluorspar district. The output from these five counties, however, makes up over 60 percent of our domestic fluorspar production, amounting to some 175,000 tons of finished product in 1956, The area is rough and hilly. It is bisected by the Ohio River, and has numerous smaller rivers and creeks. Add to this a generous average annual rainfall, in excess of forty inches, and it is understandable that the-area-can boast of an ample water supply. An abundance of water, however, is unfortunately not always conducive to ideal mining conditions. The faulted structure of the area and the soluble Mississippian limestones make the subsurface sediments' willing hosts to the surface water. Limestone cavers and sinkhole topography also compound the occurrence of underground water. It is little wonder, then, that water frequently presents an economic problem in the area, particularly in vein-type mining.

Jan 1, 1958

By C. Trepka-Bloch

Silver-copper-zinc mineralization is confined to metasomatically altered late Paleozoic and Cretaceous sediments consisting predominantly of limestone, siltstone and sandstone units. Mineralized alteration halos are spatially and presumably also genetically related to the emplacement of a Cretaceous quartz monzonite stock. Several generations of ore formation and alteration took place. Distribution of skarn and ore was influenced by intrusive contacts, calcareous horizons and by relatively less permeable rock units which served as barriers. Most of the ore bodies form conformable near horizontal mantos but some follow steeply dipping monzonite dikes. Structurally controlled alteration pipes connect the mantos locally. The deposit is strongly affected by mineralized fault and breccia zones.

Jan 1, 1986

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016