Search Documents

By J. D. de V. Louw

Introduction Zircon is a natural occurring mineral and may exhibit natural low level radioactivity. It contains trace levels (90 to120 pCi/g and 110 to 115 pCi/g respectively or 3.3 to 4.4Bq/g and 4.1 to 4.3 Bq/g) of naturally occurring radioactive uranium and thorium. This mineral is often found in a suiteof minerals (rutile, ilmenite and monazite) Due to the overlap in physical properties of monazite (containing 4–7% thorium) with some of the zircon (slight magnetic susceptibility) it often contaminates the zircon, adding to the levels of thorium in the product. Hazards associated with the products from zircon and its processing is inhalation of respirable dust (generated by milling) containing radioactive uranium and thorium which may cause cancer of the lungs. Legislature regulates the transport, use, workplace environment exposure and storage of radioactive material. In America the general regulation for the unlicensed use of low levels of radioactive materials limits the concentration to 500 ppm (U plus Th). Europe (IAEA) specifies a limit of10 Bg/g (Bequerels per gram) on the parents for transport only which is a higher level of U+Th. Companies selling into these markets need to comply with these regulations and certification is therefore required, not only of the major constituents determining the price, but of the U and Th levels as well. Exceeding the limits for U and Th may result in material being returned to the country of origin. However, for the analyst the requirement is to analyse for these elements throughout the production process as well as the analysis of the ‘tails’ that is returned to the mine area. This requires a wide range of concentration to be analysed. Methods of analysis A wide variety of methods exist for the analysis of U and Th in a range of matrices. (Table I) All these methods have been used with varying degrees of success in terms of accuracy. Overall precision for the different techniques varies from 5 to 25% relative. Time to produce results from these methods vary from a few minutes to several days. The Production Chemist is expected to produce between5 and 10 analyses per hour for process control purposes. A suitable technique that fits this requirement is X-Ray Fluorescence. Both Wavelength Dispersive (WDXRF) and Energy Dispersive X-Ray (EDX) instruments are suitable. X-Ray analysis in general has a few major advantages over competitive techniques. •It is fairly simple to set up and interferences are known and easy to correct •It has multi-element analysis capabilities •Clean spectral lines for U and Th (in zircon specifically) •Uncomplicated and easy to measure background •Low detection limits (3 to 5 ppm) •A very high degree of precision •Sample preparation is uncomplicated and fast (pressed powders and fused beads). In Zircon (ZrSiO4) processed sands the matrix is constant(>99% ZrSiO4) and the background is thus essentially constant. A typical set up for the analysis of U and Th by WDXRFis given below: X-Ray Tube Tungsten (W) Target, 2.5 to 3kW operated at 50mA/50kV Crystal LiF200 (or LIF220 for higher resolution) Analytical Lines (2?)U La1,226.14Th La1,227.47 Detector Scintillation Counter Analysis time, depending on the concentration can vary from as little as 20 seconds up to 5 minutes. Standards As with any other comparative technique XRF analysis relies heavily on the quality of the standards used. Assuming proper set-up and operation of the instrumentation as well as consistent sample preparation, accuracy is determined by the quality of the initial calibration standards. A search for the available zircon certified reference materials (CRMs) shows that there are only a few CRMs

Jan 1, 2003

By J. M. Benson

Titanium is an exciting structural material that can offer significant strength-to-weight advantages over currently used alloys. However, its Achilles? heel is its costly, energy-intensive production process that effectively eliminates it from competing with aluminium and high-strength steels, apart from critical applications where titanium forms only a small component of the total cost. Current attempts are being made to reduce the cost of titanium products and these recognize the importance of minimizing the costs over the total production chain. Powder metallurgy (PM) technologies play a crucial role within this, as the output of the existing and potential primary metal production methods is in the form of sponge or powder. By using PM, costly remelting and forming operations can then be avoided, except in the manufacture of large components. Metal injection moulding (MIM) is an effective process for producing complex net-shape components in large volumes from metal powders. Nevertheless, the commercial use of titanium powders in this process is still in its infancy. The only major supplier of feedstock utilizes a polyacetal-based binder. This gives good green strength but requires a catalytic nitric acid process to remove most of the binder prior to thermal treatment. As this involves additional and expensive equipment and is a potentially hazardous process, there is interest in finding an alternative binder system that can be debound either purely thermally or that involves a less hazardous, more environmentally friendly solvent. This paper describes the use of capillary rheometry to characterize the influence of temperature and shear rates on the flow behaviour of potential binder systems for titanium MIM feedstock. Keywords Titanium, metal injection moulding, capillary rheology, feedstocks, powder loading.

Jan 1, 2011

By L. Jurca, C. Gligor

After 1990, a great process of re-organisation and economic reform has occurred in the Romanian mining sector and especially in the pitcoal mining in the Jiu Valley. This process has included both legislation and the main aspects for getting an economic efficiency in the environment issues and for dealing the problems with social impact. Accordingly, starting with the year 1993 a new mining method has been introduced to turn efficient the pitcoal mining, and we speak about mining with caved in bed. This method has two variants: - with transverse strips and caved in bed; - with long face and caved in bed. Each of the above-mentioned variants has in turn several subdivisions, depending on how the longwall is prepared and on other characteristics. By using this method, the output has increased compared to other mining methods. The main safety aspects concerning caved in mining refer to: - great emissions of methane; - technical aspects (a mining method system, supports, discharging process); - pressure driving (analysed for the case of mining with long face, with transverse strips as well for the case of transverse strips when mining a subsequent sublevel).

Jan 1, 2003

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By G. B. Dukes

Scaling of rockpasses was problematic at Tau Lekoa Mine prior to production commencing in 1991. High horizontal stress levels relative to the host rock mass strength have been instrumental in causing the observed scaling. Scaling has been more pronounced in the deeper rockpasses and these are monitored regularly. Rehabilitation of one of the reef passes and one of the waste passes was required in the period 1999 to 2001. This paper describes the extent of the problems experienced to date as well as the rehabilitation completed.

Jan 1, 2006

By L. Sahu, S. Bhattacharya, S. Dey

"An ideal procedure to determine the limits of flotation-based separation, as is the case with washability analysis for density separation, does not exist. Therefore, a procedure called release analysis, considered to be the counterpart of the washability process in density separation, was developed to evaluate the flotation characteristics of coal fines. Since flotation is a complex process it is necessary to know the maximum recoverable yield that could be achieved at a target ash level and what could be obtained by release analysis. Due to a number of limitations in the initial procedures, modifications were recommended by various researchers to generate an optimum separation curve. This paper presents a review of, and a discussion on, the chronological evolution of release analysis methodology over the decades. Notwithstanding the availability of a standardized release analysis procedure, such as BS 7530, the paper highlights the critical parameters involved in the procedures, such as coal type, feed characteristics, choice of reagents and dosage, operator bias, and design features of the flotation cell IntroductionCoal is a heterogeneous substance consisting of various combustible constituents (macerals) and associated mineral matter. The kind and abundance of the various macerals present in the coal, such as vitrinite, semivitrinite, exinite, and inertinite, determine the type of coal. As macerals are formed by biological degradation of different parts of the plant material, they have different properties based on their original composition. Coal cleaning processes are dependent on the differences in physical properties between the coal components (the macerals) and also between the macerals and the mineral matter. Thus the cleaning characteristics of the coal might vary from one type to the next. The cleaning processes influence the distribution and the concentration of macerals in the various size and density fractions of the cleaned product."

Jun 1, 2019

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By J. M. Font, R. G. Reddy

Jan 1, 2004

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

In their excellent paper, Milev and Spottiswoode have provided quantitative and definitive descriptions of an important phenomenon that hitherto has been largely the subject of conjecture. They convincingly show that ?site-response? can amplify the strong ground motions on the rock-wall of a stressed tunnel by a factor of 10 to 12 compared with the PPV in the solid rock mass (at the same distance from source). This knowledge gives us a firm foundation from which to begin to build an understanding of the mechanism of damage resulting from a rock burst. Regrettably this understanding is still far from adequate, in my opinion. The authors of this paper, however, have made some statements that are too reassuring and which tend to reinforce the sense of complacency that prevails among many members of the rock engineering community on the deep gold mines.

Jan 1, 2006

By A. Ahmed, A. Fathy, M. Eissa, K. El-Fawakhry, A. El-Mohammady

Silicomanganese is widely used as a complex reducer and an alloying addition in the production of various grades of steel due to its economic and metallurgical advantages. It is also used as a semi-product in the manufacture of medium- and low-carbon ferromanganese and metallic manganese. Manganese-rich slag, resulting from high carbon ferromanganese production, has the advantages of high manganese content, high Mn/Fe ratio, low excess oxygen, low phosphorus content, low fine content and low cost. Such slag seems to be very attractive to use as raw materials for the production of silicomanganese alloys. In the present study, experimental heats were designed and carried out to optimise the factors affecting the production process of silicomanganese using manganese rich slag in the charge. The results of pilot plant experimental heats showed that the optimum metallic yield and recoveries of manganese and silicon are obtained with initial slag basicity,(CaO + MgO) / (Al2O3), equals 1.8 by using dolomite as fluxing material and charging quartzite and fluorspar in percentage of 25% and 4% of the blend, respectively. The results showed also that an amount of 30% of coke in excess of the stoichiometric amount should be added. These result are relative for the specific high Al2O3 ores used.

Jan 1, 2004

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 357 to 366 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2002 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 26 July 2002 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2002 set out on page 357 to 366 wereapproved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2002

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009