Search Documents

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By D. F. Malan

This study reviews the concept of squeezing (large time-dependent deformation) in rock and investigates the possibility of this phenomenon becoming more pronounced in the planned ultra-deep mines of the South African gold mining industry. Although squeezing behaviour is not commonly found at the current depths of the gold mining industry, it is observed at Hartebeestfontein Mine due to a combination of weak rock and high stresses. Calculations based on the average strength of the Witwatersrand quartzites and the competency factor used to identify squeezing conditions in civil engineering tunnels, indicate that there is an increased risk of squeezing behaviour in ultra-deep mines. This will adversely affect the profitability of these mines and highlights the need for further research into the time-dependent behaviour of rock. Finally, the current support strategies in squeezing conditions are reviewed.

Jan 1, 1998

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By R. L. Castro

The extraction of ore in panel caving operations also involves the coextraction of non-economic material, known as dilution. Forecasting, avoiding, and understanding the mechanics of dilution is critical to longterm planning. The models of dilution that are currently in use in panel caving operations are those by Laubscher (1994), who postulated that dilution is due to gravitational flow and depends on the height of interaction, the column height, and the draw uniformity. This paper presents a back-analysis of extraction and dilution behaviour at Codelco?s El Salvador and Andina Divisions, which use panel caving as a mining method. This analysis was conducted in order to review the existent dilution entry mechanisms and calculation methods. Three sources of dilution were identified. The first source is ?gravitational dilution?, which is due to gravitational flow and mixing as dilution migrates by gravity from a sector located above the panel under analysis. The second source of dilution is ?caving dilution?, which occurs when an air gap is formed in a large area and a sudden propagation of a hang-up occurs, inducing early ingress of waste into the production level from a level above. The third mode observed is ?lateral dilution?, which occurs when the panel is located next to an exhausted sector and the broken material enters the draw column early during draw. In the last two cases, dilution could migrate large distances horizontally. The mine data indicated that draw and caving strategy are key for long-term planning of large panel caves.

Jan 1, 2014

By S. C. Gouws

"SynopsisSustainable infrastructure development has long been identified as a key enabler for socio-economic growth and poverty reduction in societies globally. Twenty-one years into the young South African democracy, economic prospects are fragile and unemployment statistics are high. According to Trading Economics (2015) the GDP growth rate in South Africa averaged 3.07% from 1993 until 2015.Through the National Development Plan 2030, the government has responded by instituting the Presidential Infrastructure Coordinating Commission (PICC) to direct national growth and drive job creation by effecting a long-term infrastructure investment programme. The Commission is mandated by Cabinet to coordinate, integrate, and accelerate implementation of more than 150 individual social and economic infrastructure plans.In the civil infrastructure development sector, increased urbanization is compelling governments and the public sector to expand safe and reliable public amenities, but the availability of real estate for construction in congested cities is a challenge. Within the mining infrastructure construction industry safe, rapid, and efficient mine extraction strategies are imperative to realize increased production, business hurdle rates, and stakeholder expectations.Asset owners and stakeholders are obliged to consider advanced mechanized underground excavation and support technologies in order to present feasible solutions timeously. From an engineering design, procurement, and construction management (EPCM) perspective tunnelling technology and boring applications have a distinct advantage over conventional excavation techniques. These solutions may enhance commerce and transportation by expanding infrastructure in concentrations of national economic activity, providing crucial linkages with rural areas, between cities, and across international borders.This paper explores the contribution by mechanized tunnelling technology and boring applications applied in conjunction with digital and automation technologies compared with conventional methodologies. The technological expertise, combined with a paradigm shift in delivery of project objectives, will promote economic growth, aid recovery from the economic downturn, and improve social development."

Jan 1, 2015

"In mechanized mining, poor equipment efficiency (availability, utilization, productivity, and quality) can endanger the success of the operation. This case study will show how an initiative to improve equipment performance developed into a comprehensive turnaround plan for the mine that placed it in the forefront of performance achievement.As part of a company-wide review process, poor overall equipment effectiveness (OEE) was identified as a major reason for the mine not achieving its targets. A project to improve the OEE identified eight improvement areas (elements) that contributed significantly to the poor performances. Measurement metrics were determined for these elements, followed by determination of baseline and target (improved) key performance indicators (KPIs). Cost savings associated with the improved efficiencies were calculated and tracked throughout the project. The mine team determined the specific actions required to achieve the target KPI in each element. These were individually developed and managed like mini-projectswith allocated responsibilities for delivery. The paper will indicate how this OEE improvement initiative triggered an improvement in almost all sections of the mine. Soon after launch, the initiative gathered momentum as the KPIs starting to improve. A visible tracking system exists at the mine and each employee can see the improvements and feel the success. The original eight elements were extended by five more, and the mini-projects grew as participants saw the success of the initiative.This paper concludes that through management and worker involvement, visible measurement and controls, and carefully chosen improvement elements, the mine was turned around. It is now achieving and exceeding its targets, and employee relations and motivation as well as safety have improved considerably. All of these achievements are reflected in the bottom line."

Jan 1, 2016

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012

By B. W. J. van Rensburg, M. J. Schmidt

Bulk materials handling systems are extensively used in the mining and minerals industry, where a fairly high incidence of structural failure is experienced, notwithstanding design compliance with appropriate standards. A number of case studies are explored to demonstrate how insufficient controls or protection systems have contributed to structural failures on mobile bulk handling equipment. The importance of design integration across engineering disciplines is highlighted. The revision of ISO 5049-1 (1994) is proposed to provide specific rules and guidelines pertaining to machine protection systems. It is further recommended that the structural design engineer of the original equipment manufacturer(OEM) fulfils a more prominent role during the final acceptance and handover of mobile bulk handling equipment, with specific reference to protection systems.

Jan 1, 2015

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By T. J. Goff

Keywords: accurate control, matte level, smelting operations, process control, tapping, sounding bar, electromagnetic measurement [ ] Accurate control of matte levels during primary matte smelting operations is desirable in order to improve process decision-making. High matte levels in the vessel could have to disastrous consequences, particularly in the new generation of intensive smelting furnace with deep-cooled copper coolers. Knowing when to commence tapping and a better understanding of melt times can only be improved if the furnace levels are monitored correctly. At Lonmin Marikana Smelter Division it has long been understood that the matte level information being provided by the manual sounding bar is only as good as the operators? following of measurement procedure, their skill in assessing what the sounding bar is displaying, and their individual interpretation of what they are looking at. This paper sets out to show how this problem was identified as an area of major concern to the plant, how a solution was sought and how an electromagnetic measurement system was installed as an alternative measurement to the matte sounding bar system. Other areas discussed in the paper are the difficulties to be overcome when first installing new equipment and how these teething problems were solved by close co-operation between Lonmin and equipment suppliers, which led to some design modifications to the delivery system. In conclusion the paper discusses the results between the electromagnetic measurement and the manual sounding measurement and how best to integrate the generated data into the plant?s process control system for improved decision making.

Jan 1, 2011

By H. H. Einstein

This paper reviews how uncertainty has been dealt with over the past 40 years using the decision making cycle as a frame of reference. The review of the phases of this cycle, as applied to rockmechanics and rock engineering, namely characterization, performance analysis, updating and decision making shows that in each, progress has been made over the past 40 years, although most of the basic concepts existed already in the 1960’s. Characterization is the area in which the greatest scientific steps were taken, this phase and performance analysis also gained from the tremendously expanded computational capabilities which allow one to use both more complex and more practically oriented models. The greatest practical advance is without using any doubt in risk based decision making although its acceptance shows interesting differences between different professions. Dans l’article suivant on utilise le cycle de décision pour illustrer le développement du traitement des incertitudes en mécanique des roches et en construction en roche dans les quarante années passées. La revue des phases du cycle de décision montre qu’on a fait du progrès dans chaque phase du cycle de décision, c’est à dire dans la caractérisation, dans l’analyse et la prédiction du comportement, dans l’actualisation et dans l’acte de décision, même si les concepts fondamentaux existaient déjà dans les années 1960. Les plus grands avancements scientifiques se trouvent dans le domaine de la caractérisation tandis que l’analyse prédictive profitait du développement de l’informatique qui a mené à des modèles plus complexes mais aussi plus pratiques. Le plus grand progrès est sans doute dans le domaine de l’acte de décision sur la base des risques. Ce procédé est devenu assez commun même s’il y a encore des différences d’acceptation entre différentes professions. Im vorliegenden Artikel wird der Entscheidungszyklus gebraucht, um darzustellen wie sich derUmgang mit Unsicherheiten im Felsbau während der letzen 40 Jahre entwickelt hat. DerÜberblick über die Phasen des Entscheidungsprozesses zeigt, dass bei der Anwendung in derFelsmechanik und im Felsbau, in allen Phasen d.h. bei der Charakterisierung, bei der analytischenVorhersage, beim Aktualisieren und bei der Entscheidungsfindung Fortschritte gemacht wurden,obwohl die grundlegenden Konzepte bereits in den 1960er Jahren existierten. Im Gebiet derCharakterisierung gab es wohl die grössten wissenschaftlichen Entwicklungen, während dieanalytische Vorhersage vor allem von den Fortschritten der Informatik profitierte, welchekomplexere wie auch praktischere Modelle möglich machte. Der grösste Fortschritt ist ganz sicherin der Entscheidungsfindung zu beobachten, wo Risikobetrachtungen gang und gäbe sind, obwohlhier noch einige Unterschiede zwischen verschiedenen Berufsgattungen zu finden sind.

Jan 1, 2003

By R. Boom, K. C. Mills, S. Riaz

This paper details the recent trends in slag-related research from 1999 to 2003. The trends in thefollowing are outlined: • Annual publication rate • Geographical origin of the work • Nature of the research (e.g. thermodynamics, kinetics) • Nature of the slag studied. This study has revealed that slag research in the USA and Europe has decreased to about a half over the last 20 years and that there has been a significant decrease in Japanese research in this area in recent years. However, these decreases have been offset by significant increases in Chinese and Korean research activity. There has been a significant increase in the amount of work carried out on the recycling and environmental aspects of slags in recent years.

Jan 1, 2004

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By H. Aykul

The choice of which mining method to use at many large surface coal mines is often dicated by what machinery is available or what experience the mine management can offer. One of the most significant surface coal mines in Turkey is owned and operated by the Turkish National Coal Board, located to the west of the city of Kütahya. The Seyitömer Lignite Enterprise (SLE) extracts low quality coal, the majority of which is supplied to an adjacent power station. The coal seems at SLE contain bands of ash which under normal mining conditions are extracted with the coal. This increases the ash content of the run of mine coal and results in lower efficiency at the power station and financial penalties for SLE. In this paper, therefore, selection of the best possible equipment and production method was identified to achieve high selective mining at SLE. The research found that two different high selective mining methods were suitable for selective excavation of the B3 seam, which were hydraulic excavator and truck and surface miner and truck combinations. It was also found that high selective excavation could provide the desired coal quality at 52% lower costs when the whole process (excavation, transportation, processing, etc.) was considered. Keywords: coal mining, surface mining, selective mining.

Jan 1, 2007

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012