Search Documents

By T. F. J. Hälbich

Namakwa Sands aims to conserve environmental resources and prevent or minimize environmental impacts from its operations. The challenge faced by Namakwa Sands is the rehabilitation of the arid winter rainfall Strandveld and lowland Succulent Karoo vegetation zones affected by its mining activities. Extensive experimentation with different rehabilitation methods resulted in the development of an effective rehabilitation programme. The use of topsoil as a seed bank and shade-cloth as windbreaks have significantly aided the rehabilitation process. The aim of the programme is to stabilize the soil environment so as to allow the germination and development of the local plant species. The ability to control wind erosion is critical to the success of the rehabilitation effort. A programme of biodiversity audits has been started to measure the recovery of plant species in the rehabilitated area. The principle of continuous improvement, coupled to site-specific rehabilitation studies, is applied to enhance the rehabilitation programme.

Jan 1, 2003

Mr D. Wilson was born in Vereeniging, where he also completed his schooling, matriculating from General Smuts High School in 1977. Mr K.A. van Gessel was born in 1937. His final studies were conducted at Delft University, where he graduated with an M.Sc. degree in mining engineering. Mr J.G. McCaUum was born in 1938 and matriculated at Jeppe Boys' High School, Johannesburg. Mr H. Scot RusseU started his mining career at Randfontein Estates Gold Mining Co. Witwatersrand, Limited, where he served as temporary Geological Assistant, Sampler, Surveyor, Shift Boss, and Mine Overseer. Mr A.M.P. Henderson was born in 1950, in Kiel, West Germany. Mr J.L. Nel matriculated in 1957. This was folowed by his atainment ofthe folowing degrees: B.Sc. (Chemistry, Physics) in 1961, B.Sc. Hons. (Metalurgy) in 1965, M.Sc. (Metalurgy) in 1967, and MDD (student of the year) in 1981

Jan 1, 1989

By D. J. H. Walker, W. H. Gibson

The inclination of any pit wall composed of stacks of benches is limited by the overall quality and structural complexity of the rock mass in which the slope is situated. For a bench stack angle that satisfies the stability criteria, various combinations of bench height, bench face angle and berm width can be used in the slope design. The bench face angle and berm width geometries must be chosen to fit the bench stack angle but must provide a berm that will be capable of catching the volume of failed wedge material from the bench faces above. Other considerations for bench height and berm width are equipment size, ore selectivity and blasting design. This paper studies the effects of different slope configurations on slope performance as it relates to wedge stability, volume of rock safely contained on berms, and rockfall. Optimisation of the geometry is carried out based on the need to minimise the volume of failed material which limits the effectiveness of the berm. This will reduce the number of rocks that can continue to fall further, reaching geotechnical safety berms or pit ramps, that put safety of personnel and equipment at risk. For general study it is most effective to investigate and compare the performances of each of a wide range of geometrical combinations of bench height, bench face angles and berm widths that fit a variety of different bench stack angles. These analyses were conducted for a predetermined bench stack height and three different bench stack angles.

Jan 1, 2006

By E. Garab, M. Pillalamarry, E. Develo

"Recent geological exploration at Rosh Pinah mine revealed that the mine’s major production is shifting towards the western orefield, which will increase the demand for air flow to be supplied to this area. A snapshot of the ventilation survey carried out in December 2014 at the western orefield drill drive B (WOF-DDRB) showed that the air flow was well below the required standards. In order to improve the existing conditions, possible options were considered and simulated using Ventsim™ software.The best option found was to replace the existing western orefield fans with the larger fans from the inactive southern orefield workings, to increase the air flow in the DDRB district. Simulation showed that as much as 20 m3/s of air can be received at the working faces of WOF 30, compared to the previously received amount of 1.37 m3/s. The economic analysis indicated that the above option can reduce the ventilation cost by N$1.9 million annually. It was also noticed that after implementing this option together with other projects, the ventilation conditions in the mine were greatly improved and currently give no cause for concern. IntroductionA good mine ventilation system should be capable of providing adequate quantity and quality of air to all working faces, and is critical to the occupational health, safety, and comfort of underground employees (Luxbacher and Ramani, 1977; Exikis and Kapageridis, 2006). No ventilation system can remain adequate indefinitely; as the mine workings are extended, the ventilation characteristics such as system pressures, air volumes, leakages, and airway resistances change considerably. Continuous improvement of the ventilation system is needed to ensure compliance with health and safety regulations (Lovejoy, 2010). It also ensures that the right quality and quantity of air is delivered to all the necessary areas at the lowest possible cost. This can be achieved by identifying inefficient airways and poorly ventilated areas in the mine and planning how best to upgrade them.The latest geological exploration shows that the focus of production at Rosh Pinah mine is shifting towards the western orefield (WOF). As mining progressed, the working areas have advanced away from the main fans, which increased the resistance to air flow drastically and resulted in increasing demands being imposed on the main fan in order to supply an adequate air flow. This process also created more leakage paths between the fan and the working areas, which has caused the air to short-circuit before it can reach the faces. Consequently, a much larger quantity of air has to be circulated by the fan so that the stipulated quantity reaches the face, which increases operating costs (Singh et al., 2004)."

Jan 1, 2016

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By K. Sørli, H. Elstad, I. M. Skaar, A. Hildal

Generally, monitoring of refractory furnace linings is of interest to the metallurgical industry. The main issues are to control wear of the furnace lining and break out of molten metal. Penetration of molten metal through the lining can cause considerable damage to equipment in the vicinity of the furnace and endanger operators. Rebuilding of a furnace lining is expensive, mainly because it stops production, but also because the lining materials are expensive. Here, two methods for monitoring the lining of a smelting furnace are presented. The methods are based on monitoring of the temperature distribution in the lining, more specific monitoring an isotherm in the lining. One method is based on the assumption of unidirectional heat flow locally, reducing the problem to a set of one-dimensional heat conduction problems. The other method is based on inverse heat conduction. In this context inverse heat conduction means estimating the wear from temperature measurements using mathematical optimization techniques. The study is based on the ilmenite smelting furnace at Tinfos Titan & Iron KS. Some results from real temperature measurements and real observations from the ilmenite smelting furnaces is presented.

Jan 1, 2003

On 8th August, 1973, 57 members of the Institute visited Prieska Copper Mine at Copperton in the North Western Cape. After tea, the group was welcomed by the Management of the Mine, and Mr Grobler, the General Manager, gave an introductory talk. After they had been taken on a bus tour of the property, the members split up into groups and proceeded underground or to the concentrator. Of special interest to the mining members were the rock-handling methods in use at the mine. The stoping method that has been adopted is the continuous, long-hole sub-level open stoping system. The broken ore is moved with rubbertyred front-end loaders from the stope drawpoints to the ore passes. On the main tramming levels, the ore is collected by electric locomotives and discharged into the main shaft system at the bottom. At the shaft ore-pass system, a gyratory crusher that can accept rocks up to 1 m in diameter has been installed. The crushed product (minus 150 mm in diameter) will then be hoisted by a Koepe winder, which has a rated capacity of 900 tons per hour. The mine is also served by a declined roadway from surface, which facilitates the movement of heavy equipment. The most striking aspect is the productivity that can be achieved by the use of a trackless-mining system. For the production of 230 000 tons per month, it is estimated that 6 stopers and 7 developers will be required. The total labour force will be approximately 2500-2000 Bantu, 200 Coloured, and 300 Europeans. Training of maintenance and operating personnel is of the utmost importance, and it was interesting to note the extent to which non-White labour is being used in these occupations. Lunch was served at the single quarters, after which the group proceeded to the airfield for the return trip to Johannesburg. On behalf of the visitors, Professor de V. Lambrechts thanked Mr Grobler and his staff for the most interesting morning and for their hospitality,

Jan 10, 1973

By N. Fardin, O. Stephansson, L. Jing

A pair of silicon rubber replicas of size 250 mm by 250 mm, from a natural rock joint, was used to produce several high strength concrete fracture replicas of different sizes, from 50 mm by 50 mm to 200 mm by 200 mm. The morphology of the concrete fracture replicas were digitized at the laboratory using a 3D-laser-scanning machine with high accuracy and resolution. The scale dependency of the geometrical properties, including surface roughness and aperture, of the samples were investigated using fractal method. The investigation was extended to study the scale effect on the mechanical properties of the concrete fracture replicas. Four concrete replicas having same geometry from each sampling size were sheared under four different normal loads. The results show that normal and shear stiffness and peak shear strength decrease with increasing sample size and decreasing normal stress. It is concluded that for accurate determination of geometrical and mechanical properties of rock joints in the laboratory and field scales, samples with size equal to or larger than stationarity limit are required. Silikongummiabdrücke der Größe 250 mm x 250 mm einer natürlichen Kluft dienten als Vorlage für mehrere Hochfestbeton Rissreplikas verschiedener Größe. Die Morphologie der Beton Rissreplikas wurde mittels eines 3D-Laserscanners hoher Genauigkeit und Auflösung im Labor digitalisiert. Die Skalenabhängigkeit der geometrischen Eigenschaften, dies inklusive Oberflächenrauhigkeit und Öffnungsweite, wurden mittels Fraktalen bestimmt. Die Studie wurde durch die Untersuchung der mechanischen Eigenschaften der Betonrepliken erweitert. Hierbei wurden vier Betonrepliken der selben Geometrie jeder Probengrösse unter vier verschiedenen normalen Belastungen abgeschert. Die Ergebnisse zeigen das sowohl Normal- und Schersteifigkeit als auch die Spitzenscherfestigkeit mit zunehmender Probengrösse und abnehmender Normalspannung abnehmen. Es hat sich gezeigt, daß für eine genaue Bestimmung der geometrischen und mechanischen Eigenschaften von Felsklüften im Labor und im Feld Proben einer Größe gleich oder größer des stationären Limits verlangt werden. Deux répliques en gomme de silicone d’une fracture naturelle, de dimension 250 mm par 250 mm, ont été utilisées pour produire des répliques en béton de haute résistance de dimensions allant de 50 mm par 50 mm à 200 mm par 200 mm. La morphologie de ces répliques a été digitalisée au laboratoire à l’aide d’un laser-scanner 3D haute résolution et haute précision. L’influence de l’échelle des propriétés géométriques, incluant rugosité et ouverture, a été étudiée en utilisant la méthode des fractales. Des essais complémentaires ont été réalisés afin d’étudier l’effet d’échelle sur les propriétés mécaniques des répliques de fracture en béton. Quatre répliques béton de même géométrie pour les différentes tailles d’échantillons ont été cisaillées sous quatre valeurs de contrainte normale. Les résultats montrent que la rigidité normale et tangentielle ainsi que la résistance de pic diminuent en proportion de l’augmentation de la taille de l’échantillon et de la diminution des contraintes normales. On peut en conclure que, pour une détermination précise des propriétés géométriques et mécaniques des fractures au laboratoire et sur le terrain, des échantillons de taille égale ou supérieure à la limite stationnaire sont nécessaires.

Jan 1, 2003

By J. Szlazak, A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents the analysis of ventilation systems used in dead-end headings, while being drilled, in coal mines. Special emphasis is put on methane and dust hazard. Mathematical model for distribution of methane concentration in a heading is given as well. This model takes into consideration sources of methane emission and change in air flow rate due to leaks in a duct line. Solving equations presented in this article enabled giving dependencies describing distribution of concentration along the heading. On the basis of these dependencies there is a possibility of determining places with higher methane concentration and ways of combating this hazard. Determining the distribution of methane concentration in dead-end headings ventilated by a separate ventilation system is of great importance as far as work safety conditions are concerned. The information obtained may be of use when finding proper places for installing methane sensors. Three kinds of separate ventilation systems were distinguished: forcing, exhaust and overlap. The development in construction of fans and spare parts of a duct line enables using both forcing and exhaust ventilation systems in headings developed by continuous miners, with length above 1000 m, in the conditions of methane, temperature and health-detriment dust hazards.

Jan 1, 2003

By H. W. J. P. Neomagus, R. K. K. Mbaya, J. R. Bunt, N. T. Leokaoke, N. W. Makgobelele

Silicon Smelters consumes more than 80000 t/a of wood-derived charcoal as carbonaceous reductant in the production of silicon metal. More than 10% of this material is discarded as fines (<6 mm) generated due to abrasion during processing. Charcoal fine residues (<650 μm) and polyvinyl alcohol (PVA) binder were used in this study to produce mechanically strong charcoal briquettes for metallurgical application as carbonaceous reductant. The PVA binder was added in mass percentages of 1, 3, and 5 wt% to the charcoal fines. The compressive strength, abrasion resistance index (ARI), drop shatter resistance (SRI), and water resistance index (WRI) were measured as functions of curing for up to 7 days under atmospheric conditions, and the results compared with metallurgical grade coarse charcoal. The ash content of the produced briquettes was found to be high (6.6–8.0%) compared with the coarse charcoal (1–3%). The 3 and 5 wt% PVA-bound briquettes were found to be the strongest, with compressive strengths of 40 and 115 kg/cm2 respectively, with WRI values of 75 and 73% respectively. The produced briquettes were found to have lower ARI and SRI values compared to the coarse charcoal. Future work should include beneficiation of the fine charcoal discards prior to briquetting, and an increase in binder addition to above 6 wt% to improve the ARI and SRIn.

May 1, 2021

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

By Y. -J. Park, K. -H. You, Y. -T. Choi, Lee. H. -W.

Many large caverns are being constructed in great depths in Korea mainly for the storage of oil and LPG. These caverns are mostly located near the port where rock conditions are reasonably good. In some instances, the horizontal stress is very high and endangers the stability of the cavern. The purpose of this study is to assess the stability of large caverns excavated in a rock mass with high horizontal stress where Ko value is close to 3. Result shows that stress exerted in the shotcrete at crown exceeds allowable value when the 3rd bench is excavated. Also found is the tensile failure of shotcrete near the boundaries between benches. In Korea werden viele grosse Kaverne fuer Aufbewahrung vom Oel und Fluessiggas in grosser Tiefe gebaut. Am Meisten befinden sich diese Kaverne in der Naehe von Haefen, wo der Fels gute Verhaeltnisse zum Bauen einer Kaverne besitzt. In einigen Faellen ist die Horizontalspannung sehr gross und dadurch wird die Stabilitaet vom Kaverne gefaerdet. Der Zweck dieser Arbeit ist die Stabilitaet des im Fels gebauten grossen Kavernes mit hoher Horiaontalspannung zu schuetzen, wo Ko-Wert sich auf 3 naehrt. Die Ergebnisse zeigen, dass die Spannung im Spritzbeton an der Krone den zulaessigen Wert ueberschreitet, wenn das dritte Bank ausgegraben wird. Im Bereich des Spritzbetons zwischen Baenke wurde das Zugversagen festgestellt. Des larges cavités nombreuses sont en train d’être construites en grand profondeur en Corée prin-cipalement pour le stocage du pétrole et LPG. Ces cavités sont pour la plupart situées près de la porte oú les conditions des roches sont résonablement bons. En quelques cas, la contrainte hori-zontale est trés haute et met en danger la stabilité de la cavité. L’objet de cet étude est d’estimer la stabilité des large cavités excavées dans une masse de roche ayant une haute contrainte horizontale oú la valeur de Ko est proche à 3. Le résultat montre que la contrainte exercée dans le shotcrete à la couronne dépasse la valeur admissible quand le troisième banc est excavé. En plus une faillite en tension du shotcrete près de la frontière entre des bancs est trouvée.

Jan 1, 2003

By S. M. Rupprecht

A deposit to be mined by underground methods can be accessed by a number of methods: ? Adit ? Decline or ramp ? Inclined shaft ? Vertical shaft. Adits are an economical approach when the orebody is above the general floor elevation i.e. suitable in hilly or mountainous terrain. Incline shafts are limited to relatively shallow deposits, and because they are developed on an incline, development lengths for a given depth are the three to five times longer than for a vertical shaft. Vertical shafts are the preferred method for deposits deeper than 300 m but the development rate is slow and construction costs are very high. Declines or ramps offer early access to shallow deposits, which develops the ore body expediently, but are generally developed at a gradient of approximately 12 per cent. Decline haulages have become an attractive alternative to shaft hoisting, and over recent years the role of decline access has become more widespread throughout South Africa. Traditionally, South Africa has enjoyed the use of shaft systems, largely due to the large knowledge base of mining the Witwatersrand Basin, where vertical and inclined shafts were the norm. South Africa has also had the advantage of cheap electricity, giving shafts a definite economic advantage. However, in recent years the national power utility ESKOM has undergone an expansion programme that has led to tariff increases of nearly 100% over a three-year period. Based on the changes in electricity tariffs and technological improvements to underground haulage trucks, the economic inputs to access development have changed. This paper reviews mine access for shallow deposits as currently applied in South Africa. Based on current economic inputs, the paper investigates at what point a vertical shaft would be more economical than a decline system utilizing typical South African mining equipment.

Jan 1, 2012

By A. P. I. Popoola, D. O. Okanigbe

Copper smelter dust (CSD) is a byproduct of copper smelting and is composed of considerable amounts of copper values and also contaminants (like silica and mullite). Silica in CSD forms Siloxane, a low density material, which is difficult to separate from the aqueous phase during solvent extraction. The need therefore arises to reduce/remove the aluminosilicates for better grade and recovery of copper in subsequent processes. This paper reports the use of two types of centrifugal gravity concentrators, namely Knelson (KGC) and Falcon (FGC), for upgrade of copper in CSD. The aim was achieved by an initial characterisation (Particle Size Distribution (PSD) and mineralogical analysis), together with Density Separation (DS) experimentation, premised on a hypothetical density difference between copper oxide and silicon/aluminum oxide. Wet screening results showed that 88.52 % of CSD particles were in -53 μm fraction. Further PSD study using laser diffraction showed the -53 μm fraction to be composed mainly of 26 μm, 22 μm and 18.5 μm fractions. Mineralogical analysis showed copper to occur mainly as oxides (24.34 wt%), but also as sulphides (7.95 wt%), and a substantial amount of aluminosilicates (42.97 wt%) were identified. Density of CSD was determined as 2.83 g/cm3. Copper content (18.02 wt%) in CSD was upgraded to 35.94 wt% in concentrate using KGC. In conclusion, the results showed good convergence between hypothesis and experiment. Additionally, it was also concluded that KGC performed better than FGC for copper upgrade in CSD. However, roasting CSD prior density separation was recommended for enhanced copper upgrade. Keywords: Copper smelter dust, density separation, solvent extraction, mineralogy

Jan 1, 2020

By J. H. Viljoen, C. H. Graan, N. B. Strydom, J. S. Greyson

M J Martinson (Fellow) There is everywhere a lamentable dearth of quantitative information on occupational factors affecting the health and safety of mineworkers, and as the authors point out in their introduction underground lighting is one of the factors which has received little attention in South Africa prior to this welcome paper. Since the authors are to some extent pioneering, it is perhaps inevitable that the paper should raise more questions than it answers, but nevertheless it provides a provisional yardstick against which the need for, and success of, remedial action may be judged. Before commenting in detail on a few aspects of the paper it may be worthwhile to summarize the statutory provisions relating to underground lighting, contained in Chapter 15 of the Regulations promulgated in terms of the Mines and Works Act 27 of 1956. Chapter 15 is entitled `Lighting, Safety Lamps and Contraband&apos;, but in the context of the present paper only four simple regulations need be noted: firstly, no person shall work or travel in an unilluminated part of a mine unless he carries a light ; secondly, adequate stationary lights shall be provided at stations and certain other localities in shafts, winzes and places used for winding; thirdly, mechanically propelled conveyances shall be provided with an effective bright light shining in the direction of travel; and fourthly, moving machinery to which personnel have access shall be illuminated so as to be clearly visible. In all four regulations the standard of lighting to be provided is wholly subjective, and under these circumstances the wide inter- and intra-mine variations in light intensity disclosed by the study are hardly unexpected. Nevertheless the data presented in the authors&apos; Table I raise three points (1) Is there any evidence that the 19 mines visited during the survey are representative of the 45-50 large gold mines in South Africa, or that the shafts selected are representative of the respective mines? Mine managers would scarcely be human were they not to offer better lit working places for the survey; perhaps the use of a scaling factor (e.g. tonnes or transit mineworkers per shift, kilowatts, etc.) for each working place might have helped to put the figures in perspective. (2) Looking at two of the more numerous - and probably important - of the ten working places included in the survey, i.e. stations and tips, one is struck by the marked. skewness of both intensity distributions (with higher frequencies at the lower intensities) and the abrupt cut-off in both cases just short of pitch darkness. Thus, of the 45 meaned readings recorded at 26 tips no less than 19 fall in the lowest range of 0,1-0,9 1m/ft2, with but one tip in total darkness; of 46 readings on 26 stations, 7 fall in the lowest range and none is in total dark-&apos;1 ness. Although a light with an intensity in the range 0,1-0,9 1m/ft2 may satisfy the regulations, it is certainly arguable that in some situations it may be safer to have no light at all. (3) In view of the skewness referred to above, one wonders how meaningful are the `total average light intensities for (the gold mining) industry&apos; quoted in Table I, which the authors compare with illumina¬tion levels found in other countries. Looking at tips again, one notes that 34 out of 45 meaned intensity readings fall below the `total average&apos; for tips, and only 10 exceed it. From this it may be concluded that a few well-lit working places included in a `total average&apos; may conceal a plethora in Stygian gloom. In their discussion the authors make fleeting reference to the effect of underground lighting on productivity and accident rates, without however quoting any South African experience in this regard. Intuitively it seems highly likely that better lighting (in the widest sense) would improve productivity and reduce accidents, and of course it is in these areas that the mining industry might seek economic justification for providing better lighting. It is all the more regrettable therefore that these factors were not studied simultaneously with the present investigation, especially at the Psychological Division of the Human Sciences Laboratory has recently published a study on underground accidents in the gold mining industry without making any reference whatsoever to lighting as a causal factor. In the event neither of the two studies enables us to make an economic appreciation of the situation, and this seems to be a classic example of a situation where some dovetailing of research effort would have greatly increased the useful return. On the effect of lighting on accidents, it may be noted that in 1939 Mickel presented some very interesting statistics to the Mine Managers Association of the Transvaal2, on the improvement in accident rates which followed the random issue of electric cap lamps to native mineworkers in the Hercules Section of E.R.P.M. the previous year. Based on a 12 month trial period in which 250 000 shifts were worked with carbide lamps and (contemporaneously) 307 000 shifts with cap lamps, the incidence of major accidents (at least one day in hospital among men using carbide lamps was 1,15 accidents per 1000 shifts, while the incidence of minor accidents (requiring dressing only) was 11,52 per 1 000 shifts. The corresponding figures for men using cap lamps were 0,79 and 7,31 accidents per 1 000 shifts respectively, representing a reduction of over 30 per cent in both major and minor accidents. While these figures are obviously dated - only men using cap lamps were issued with hard hats, for instance - they do indicate a need for similar research today.

Jan 1, 1971

By P. van der Steen

This paper examines the historical developments in diamond beneficiation technology and the impacts on the industry. The art of diamond beneficiation has given way to the application of scientific process, but at considerable capital expenditure. The shift in beneficiation methodologies has been disruptive to the traditional skills set of the industry, but evolutionary change continues and has been beneficial to the quality of the final product.

Jan 1, 2010

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

The Skorpion Zinc Project demonstrated the viability of the production of zinc from non-sulphide (commonly called ?zinc-oxide?) ores, using the leach/solvent extraction/electrowinning process route. The success of Skorpion raised the profile of a number of other zinc oxide deposits, considered to be similar. However, a study of three such deposits demonstrates that the application of whole-ore-leaching may be limited and that the concentration of zinc, or at least the separation from acid-consuming gangue minerals, prior to leaching is essential to the successful recovery of zinc from these deposits. The recovery of zinc is dependent on an understanding of the geology of the deposit, the mineralogical association of zinc minerals with gangue minerals (Boni, 2005) and limitations of mining practice. Flow sheet development and the associated metallurgical test work to derive an economically viable treatment route from two of these deposits are discussed. Key parameters affecting zinc recovery by gravity separation and flotation are presented, demonstrating that even minor differences in mineralogy have a profound impact on zinc recovery and reagent consumption. The study also deals with the determination of appropriate design parameters through metallurgical mapping of the dense media separation process.

Jan 1, 2008

By D. Bessinger

The present paper provides a brief overview of the thermodynamics of titania rich slags, an outline of the Multi-Phase Equilibrium (MPE) package and its application to ilmenite smelting. Through assessment of published experimental data on various systems containing TiOx, it was found that despite considerable scatter in measured phase equilibria data for the binary Ti2O3-TiO2system,the behaviour of binary and higher order titania rich slags and oxide solid solutions phases could be represented by solution models in the MPE package. Results from the applications of the MPE model on the stability of solid phases and slag-refractory interactions will be presented and discussed. Parallels will be drawn between the predictions by the model and observations made during pilot plant tests. Key words: Thermodynamics, titania slags, ilmenite smelting, phase equilibria, refractory.

Jan 1, 2003