Search Documents

By L. V. Clark, Arthur La Motte

"INTRODUCTION The U. S. Bureau of Mines in 1930 and 1931 made a study of the properties and characteristics of liquid-oxygen explosives (L.O.X.) at the request of one of the largest users, in order to determine and eliminate the hazards attending its use.This report deals with the examination of absorbents for L.O.X. to (1) determine their most desirable and most undesirable characteristics, (2) to find ways and means of desensitizing absorbents to mechanical shock, and (3) to determine the effect that such desensitization of absorbents has on the explosive Characteristics of L.O.X.ABSORBENT MATERIALS The absorbent used in driving the Simplon Tunnel, the earliest project in which L.O.X. was used, was composed of crude petroleum, soot, and kieselguhr. During the World War, powdered cork, soot, sawdust, powdered straw, or other similar powdered materials were mentioned in the German military instructions for use of ""liquid air"" explosives. At that time the common types of absorbent, materials were compounded ones containing the above ingredients as well as kieselguhr, paraffin, gas oils, charcoal, bituminous coal, etc.Kuryla and Clevenger4 investigated absorbents of the above type and made the following statement concerning them:"

Apr 1, 1932

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

Mineral production was of little significance in the country's economy, and Bangladesh was not a world-ranked producer of any mineral commodity during 1977. Natural gas was the most important mineral exploited; however, reserves were sufficient to allow for much greater production, Economically, Bangladesh made some progress in 1977-782 in its struggle against poverty, underdevelopment, and rapidly increasing population. The gross domestic product (GDP) grew 8%, mainly owing to a 13% increase in food grain production, the key economic indicator in this highly agricultural nation. GDP at current prices dropped slightly in Fiscal Year (FY) 1976.77 to $6.6 billion3 and rose to $7.2 billion in FY 1977.78. The population rose from 81 million in FY 1975-76 to about 85 million in FY 1977-78, resulting in an increase of per capita GDP from $83 to $85 during the same period. The high annual population growth rate, over 3% in 1976 and about 2.8% in 1977, was recognized by the Government as the main problem facing the country. Average density was 525 people per square kilometer. A similar density would have the entire world population living within the continental United States.

Jan 1, 1981

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By C. B. DUTTON, W. F. RITTMAN, E. W. Dean, M. S. HOWARD

NOMENCLATURE USED IN THIS REPORT. In this report the ending ene has been used throughout, except in the bibliography and in quotations from the writings of previous investigators, for all aromatic hydrocarbons, as, for instance, benzene, toluene, xylene. The ending ol, though largely used in technical description, is not correctly applicable to these hydrocarbons, and should be used to designate the impure mixtures of commerce, as distinguished from pure chemical compounds. PRESENT STATUS OF PETROLEUM-REFINING INDUSTRY. Although petroleum is widely distributed, being found in many parts of the world, and although information as to its occurrence and general characteristics seems to have existed from vcry early times, our knowledge of the chemical nature of this substance has been acquired largely within the past 40 years. Within this period a voluminous literature has accumulated, which records work as painstaking as has ever been undertaken in the whole field of chemistry, such as that of C. M. Warren, F. H. Storer, S. P. Sadtler, S. F. Peckham, and C. F. Mabery. Despite this fact, the commercial method of treating crude petroleum for the purpose of procuring marketable products is, in the main, essentially empirical. Much knowledge has been acquired as to methods of separating from crude petroleum such products as are desirable commercially, but little has been done to attain the maximum recovery of such products.

Jan 1, 1916

By D. Harrington

This circular presents part I of a series of papers of a review of the literature on air conditioning in mines, with particular reference to the health, safety, and efficiency of miners. It deals with the physiological aspects of exposure to air contaminated by organic matter, noxious and toxic gases, and dusts that emanate from various sources in underground workings; part II will discuss the relation of abnormal mine temperatures and humidities to the health and efficiency of minors; and part III will describe theoretical and practical methods of air conditioning mines to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts or the world.

Jan 1, 1938

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

By Frank L. Wideman

THE TREND towards larger quantities of waste in materials handled at metal and nonmetal mines (excluding fuels) continued. A gain of 10 percent from 1962 in the tonnage of waste removed in mineral operations reflects the kind of technological problems being encountered. Technology has a major role in the mineral industry in the task of supplying raw materials obtained from resources occurring beneath the surface of the earth and used in manufacturing commodities essential to modern living. Changes in technology are often brought about by such factors as variations in economic conditions, differences in physical properties of raw material and changes in mineralogical compositions of ore. Mining is usually begun on the richest and most accessible of known deposits, and when these are exhausted, is continued with leaner ores or with less accessible deposits that are either lying at greater depths or are more remote from markets. The increasing difficulties of extraction and depletion of reserves are offset by improvements in extraction technology, improved transportation, and exploration for new deposits. Although depletion has prevailed at many individual mines and in many districts, technology has been the means of providing for increasing demands of an expanding economy with adequate supplies of minerals despite either the changing character or decreasing grade of certain ores. This has been accomplished by various methods applicable to minerals. Among the implements of technology are utilization of lower grade or more complex refractory ores by mass mining, concentration, processing, recovery of byproducts, and mechanization. Better methods to find concealed deposits or to penetrate to greater depths also have been helpful in maintaining a supply of particular minerals.

Jan 1, 1964

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation's defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By A. C. Fieldner

"Gas hazards may be divided into two principal classes- namely (1) inflammation and explosions; (2) asphyxiation and poisoning. Inflammation and explosion are prevented first by adequate ventilation so that gas sufficient to propagate flame or explosion can not accumulate, and second, by avoiding sources of ignition such as open lights, flames, sparks, electrical arcs, short circuits, or sparks. Ventilation is also the best preventive measure against asphyxiation and poisoning from toxic gases. When men must enter unventilated or poorly ventilated places containing poisonous or asphyxiating gases, suitable gas masks, hose masks, or oxygen breathing apparatus should be worn. As a rule, loss of life and property from gas hazards is due to ignorance of the properties and hazards of various gases commonly used, and consequently a failure to use proper measures for eliminating and meeting these dangers. It is the purpose of this paper to describe briefly the common gases and vapors with respect to the hazards involved in their use and to discuss the necessary precautions and methods for avoiding these dangersLight, heat, and power are prime essentials of our modern industrial civilization. The combustible gases and vapors used for the production of these necessary elements of our existence comprise the largest and most common group of domestic and industrial gas hazards. Almost every individual in his daily life subject to possible danger from asphyxiation, fire, or explosion due to one or more of these gases. For evidence one need only refer to the daily newspaper where headlines such as the following are frequently seen; ""Family asphyxiated by carbon monoxide from gas heater;"" ""Schoolhouse wrecked by gas explosion in basement;"" ""Man killed by automobile exhaust fumes in his garage;"" ""Fireman overcome by smoke fumes in basement ""Woman"".""Boman severely burned by accidental ignition of gasoline used in cleaning gloves;"" and 'in recent Years we often see ""Building wrecked by explosion of still in residential district.""It will be noted that these accidents are due to inflammation, explosion, or asphyxiation. Any combustible gas or vapor, when mixed, with air or oxygen within certain limiting proportions, will explode on ignition. The violence of the explosion varies with respective proportions of air and gas, and with the degree of confinement of the mixture. For example: Mixtures of natural gas and air containing between 4.5 and 12 per cent natural gas will explode, or propagate flame throughout the mixture without the continual presence of the source of ignition that started the inflammation. The table following gives the explosive limits of the common combustible gases and air:"

Jun 1, 1926

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation&apos;s petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By V. Vern Hutchison

This selected list contains 829 entries with citations to Bureau of Mines publications related to petroleum and natural gas, which were released during the 1961-1970 period. Some entries are multiple in nature, resulting in a total of 881 citations.

Jan 1, 1972

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977