Search Documents

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By C. A. Wilson

The Bureau of Mines started a continuing program to investigate and evaluate analytical techniques to assist governmental agencies to select simple, rapid, reliable methods for crude oil spill identification. Six crude oil samples were analyzed to evaluate gas-liquid chromatography, atomic absorption spectrophotometry, infrared spectoscopy, sulfur and nitrogren determinations, mass spectrometry, nuclear magnetic resonance spectroscopy, and ultraviolet spectrophotometry. Samples were studied from the following selected fields: El Morgan, Egypt; Duri, Indonesia; Minagish, Kuwait; Bachaquero, Venezuela; Gach Saran, Iran; and Prudhoe Bay, Alaska. These samples were chosen to represent high-production fields that are likely to be involved in oceanic transport. Over 50 years of Bureau of Mines analytical research on petroleum served as the basis for evaluation of the experimental results to determine which of the methods are effective techniques to identify crude oil spills. Gas-liquid chromatographic analysis, atomic absorption spectrophotometric analysis, and sulfur-nitrogen determinations are recommended as the most useful of the techniques investigated.

Jan 1, 1975

To develop a cost-effective tool for improving the performance of rock drilling systems used in detecting and delineating underground mine voids and for coal exploration. Approach To investigate admixtures of polyethylene oxide (PEO) at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life in rock drilling systems. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the surface of the rock being drilled. Laboratory drilling studies have been performed on rock types such as quart¬zite, granite, taconite, and marble. The lab tests were conducted using 5/8-inch diameter diamond-impregnated coring bits with cationic compounds as the surface charge neutralizing additives. These studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition.

Jan 1, 1991

By R. E. Brown

The objective of this Bureau of Mines study was a laboratory-scale evaluation of the sodium sulfate refining process for removing copper from molten ferrous scrap. Maximum copper removal is achieved in carbon-saturated melts at 1,300° C. Low carbon concentrations and higher temperatures result in a less efficient copper removal and an increased sulfur concentration in the iron. Sodium sulfate refining significantly lowers the concentration of aluminum, manganese, and silicon; however, the copper removal efficiency is adversely affected by the presence of manganese and silicon. Compared with other reagents tested, sodium sulfide-forming slags were found to be the most suitable for both copper removal and sulfur control. The sulfur content of the refined iron was higher in tests conducted in acid-type refractory crucibles. Earlier studies showed that tin, a significant metallurgical impurity, is not removed by the sulfate process. During the present investigation, results showed that chlorination, using organic solid sources of chlorine, reduced the tin concentration to acceptable levels in molten iron.

Jan 1, 1975

By Mark Larson, Steve Iverson, Brian G. White

The authors hypothesize that excavation-induced extension fractures are caused by elastic shearing displacement that in turn causes tension oblique to a propagating shear zone. Such extension is manifested as tension on scales larger than that of microcracks. En echelon fracture patterns are a common result. FLAC modeling confirmed that localized tension is created near the corners of mine openings. In the model, tension was concentrated at the leading edge of a simulated fracture in a pattern that could promote the formation of an en echelon fracture. Particle Flow Code models confirm progressive formation of en echelon tensile failures with distance from an opening. The elastic displacements and the resulting fractures facilitate reduction in applied load at the expense of shear deformation and lateral dilation. Understanding the mechanics of fracture and deformation is vital for designing more effective ground support practices, a major objective of ground control research being conducted at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health.

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By L. C. IlsLey

A preliminary investigation has recently been made by the U. S. Bureau of Mines to determine whether or not the ordinary mine- type telephone is entirely safe in gaseous atmospheres . Two well known makes of mine- type phones were purchased for this investigation . It is not conceivable that the current necessary for talking over telephones could ignite gas . However , such phones are provided with efficient magnetos , and it was believed that danger might result from the ringing of the magneto . Again , while this type of phone has been designed to have a certain measure of dust and moisture tightness , evidently it has not been designed as an explosion- proof device . either with regard to cover joints and fastenings or strength of castings . Therefore , the problem was simplified . First it was assumed that owing to the construction of the telephones the gas would penetrate into their interior , and the question was to ascertain whether or not the gas would be ignited from the operation of the magneto .

Jan 1, 1922

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1965 was improved slightly, as indicated by the reduced injury-frequency and severity rates. The overall operating activity was higher in 1965 as measured by the gains in the number of men working and in the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.65 per million man-hours in 1965. This overall rate comprised frequencies of 0.28 for fatal and 17.37 for nonfatal work injuries, of which both were slightly better than the corresponding rates of 0.29 and 17.53 in 1964. Fatalities totaled 537; 5 less than in 1964. However, the total of 32,982 nonfatal injuries was 575 higher than in 1964. This larger number of nonfatal disabilities was offset by the increased worktime so that the nonfatal frequency rate decreased in 1965.

Jan 1, 1967

By Sean Gallagher, Thomas G. Bobick

The Bureau of Mines performed a pilot study examining the effects of posture on back strength and Maximum Acceptable Weight of Lift (MAWL) on six healthy male subjects (M = 32 years + 4 SD). Six hack strength measurements (3 static and 3 dynamic) were made while the subjects were kneeling and standing. In addition, these subjects (who were unaccustomed to lifting in these postures) volunteered to participate in a study of psychophysically determined NAWL in both postures. Results of the back strength tests showed a significantly lower peak torque per body weight output in kneeling versus standing hack strength measurements for five out of six test comparisons (p < .05). Subjective estimates of lifting capacity in the kneeling posture were significantly lower than those for the stooped posture (p < .05). The results of tests of hack strength and lifting capacity in these two postures provide useful information to consider in determining the physiological and psychophysical stresses imposed by these

Perform laboratory tests to measure the vibration attenuation characteristics of off-road vehicle operator seats for various types of seat suspensions, cushions, and seat adjustment settings. Background A study was conducted by the U.S. Bureau of Mines to determine the probability of whole-body vibration (WBV) exposure for a large class of off-road machinery operating in surface coal mines. The study determined that mere than 40 pct of off-road equipment operators were exposed to WBV exceeding the standard fatigue-decreased-proficiency (FDP) level defined by the International Standards Organization in its guideline ISO standard 2631. The tire-terrain interaction of a moving vehicle generates vibrations that are transmitted through the ve¬hicle suspension, cab mounting, and seat. The final point of transmission of vehicle vibration to the operator is through the scat. A seat that provides good vibration isolation and allows good vehicle control is of prime importance to operator safety and health.

Jan 1, 1993

By C. M. Mason

A method for evaluating the relative incendivity of detonating cord in natural gas-air mixtures was developed. The method consisted of firing short lengths of cord in bundles to determine the number of strands per bundle which would ignite natural gas-air mixtures 50 percent of the time in the 45-cubic-foot gallery of the Bureau of Mines. The relative efficiency of a flame quenching agent, potassium acid tartrate (KHT), when incorporated in both the pentaerythritol tetranitrate (PETN) core and the polyethylene sheath, was explored. The effects of sheath thickness, sheath composition, core weight, and core composition were evaluated. The bundle method established a quantitative scale for evaluating the relative incendivity of cords. The relative incendivity determined by the bundle method was then compared with the incendivity of 100-foot lengths of detonating cord when initiated in 8 percent natural gas in the 640-cubic-foot gallery of the Bureau of Mines.

Jan 1, 1968

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan&apos;s toxicity,

Jan 1, 1982

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

By David K. Ingram

The development of large open surface fractures over mined-out coal longwall panels is the focus of this U.S. Bureau of Mines report. The research concentrates on defining the fractures characteristics and their controlling variables. The investigation was conducted at two mines in south-central West Virginia. All but one of the fractures are subparallel to the trend of the underlying longwall panel. One fracture is perpendicular to the trend of a longwall panel. Overall length of the fractures ranges from 60 to 900 ft. In cross section they are V-shaped, ranging from a couple of inches to 25 ft in width at the surface, but narrowing as they increase in depth. Fracture depth varies from a few inches to over 50 ft into bedrock. A vertical fracture or joint plane was observed in the bedrock at several open zones along the fractures. All of the fractures vary in elevation and do not parallel surface contours. The fractures are aligned with local joint trends, they correlate with longwall development, and they are situated in an increased tensional area over the mined out longwall panels. These observations indicate that the fractures are tensional openings along preexisting joint planes possibly triggered by longwall mining.

Jan 1, 1989

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

1. Introduction This document represents Part II of our final report on the development of a "Remote Sealing System for Extinguishing Coal Mine Fires. " It is a technical report which summarizes the results of system development and field demonstration. Part I of this two - part final report is an Operator&apos;s Manual for the application of the Remote Sealing System to a coal mine fire. 1.1 Background When coal mine fires go out of control and can no longer be fought directly, the standard fire fighting technique is to construct air-tight seals in the mine passages leading to the fire area so&apos;--,that the oxygen supply to the fire is". cut off. Ultimately, it is desirable to isolate the fire zone in such a way that normal operations can resume in the remainder of the mine. The construction of seals in the- mine causes the atmosphere to pass through a toxic and explosive phase. Explosions, if they occur, are not only hazardous to the men working at the sealing operation, but can also undo much of the sealing work which has already been accomplished. Sealing of passageways surrounding the fire zone from within the mine is extremely difficult and dangerous. Methods for direct sealing are detailed in "Control of Mine Fires&apos;. 1 An alternative to this approach is the technique of remote sealing. This involves drilling boreholes which intersect the mine passages at the locations where the desired seals are to be constructed. The seals are then constructed by pouring material down the borehole and filling a segment of the passage from bottom to top. During this operation, there are no personnel in the mine, all operations taking place on the ground surface.

Jan 1, 1973