Search Documents

By Manuel Gomez

Areal distributions for ash, total sulfur, and sulfur forms were developed for the top 12 inches, the middle section, the bottom 8 inches, and the total seam of Pittsburgh coal in southwestern Pennsylvania. The sulfur and ash exhibit an apparent high local variability. As a general rule, both the sulfur and ash show high concentrations in the top 12 inches and in the bottom 8 inches of the seam relative to the concentrations observed in the middle section of the seam. The high-low sulfur and ash concentrations in the top 12 inches of the seam are not coincident with the high-low sulfur and ash concentrations in either the middle section or the bottom 8 inches of the seam. With respect to sulfur and ash, it is suggested that the top and bottom sections of the Pittsburgh coal may reflect both a syngenetic and epigenetic origin. Present data support the belief that paleotopography controlled Pittsburgh seam deposition. Evidence is presented to show that channels were cut at various times into the semilithified sediments that buried the Pittsburgh seam. In this channeling process, portions of the Pittsburgh coal may have been eroded away. Following channel development, the lower part of the Pittsburgh sandstone filled the complex system of braided channels to produce the "want areas" encountered in present mining operations. In localized areas of the Pittsburgh seam, impingement of Pittsburgh sandstone may be responsible for the lateral displacement of the coal. Information of this type becomes important in the assessment of exploration data, in the development of a quality control system for mine output, and in mine life planning.

Jan 1, 1974

By Berenice B. Mitchell

THE STATISTICAL tables in this chapter present, country by country, the mineral production of the world in 1949-50. The figures are on a mine basis, unless otherwise indicated, except for cement, coke, and steel, which are measured at the processing plant. The tables are essentially a retabulation, by countries, of the 53 commodity world tables appearing in the various chapters of this volume. For lack of comprehensive information, data for the following minerals are excluded: Andalusite, aplite, asphalt, boron, bromine, calcite (optical), calcium chloride (natural), carbon dioxide, clay, columbium (niobium), diatomite (kieselguhr), dumortierite, emery, garnet (abrasive), gem stones (other than diamonds), germanium, greensand, grindstones, helium, indium, iodine, kyanite, lithium, magnesium compounds (other than magnesite), meerschaum, mineral pigments, monazite, natural gas, natural gasoline, oil shale, olivine, perlite, pumice, quartz crystal, radium, sand and gravel, selenium, sillimanite, sodium salts (other than common salt), stone, strontium, sulfur (byproduct), tantalum, tellurium, thallium, topaz (industrial), tripoli) uranium, vermiculite, wollastonite, and zirconium. In addition, a few minor geographic areas for which no statistics are available, are also omitted from the tabulation; it is believed that no significant quantities of minerals are mined in any of these areas. The statistics in these tables were derived principally from questionnaires sent, in cooperation with the United States Department of State, to the governments of each country. Supplementary sources were United States consular reports, the Imperial Institute's Statistical Summary of the Mineral Industry of the British Commonwealth and Foreign Countries, other official publications of various countries, the United Nations Statistical Yearbook, the Year Book of the American Bureau of Metal Statistics, Minerais et Metaux, business magazines, and company reports. Where official data were not available, esti-

Jan 1, 1953

By A. L. Murray

"Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years, and in most mining towns of the state, both the operators and their employees deserve much credit for the efforts put forth to better the living, working, educational and recreational conditions. Progress has been and is being made, but there are still a few important towns where purer water and better sewage disposal are pressing needs.In the older metal-mining towns that are incorporated and are independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking toward improved welfare conditions than in company towns controlled by the mine operators.However, even in such towns the companies can do much to better welfare conditions, as shown by the progress in Bingham Canyon during the past several years. The Utah Copper Company has spent $800,000 since 1920, in the erection of modern brick cottages, apartment houses and the Germnell Memorial Club. The cottages and apartment houses have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club erected and equipped at a cost of $175,000 was provided by the company for the benefit of the Utah Copper employees living in the canyon and has been made the recreational center for the camp. Another improvement is the $100,000 fireproof hotel built by the United States Mine of the United States Mining, Smelting and Refining; Co. in the Copperfield section of Bingham Canyon. This hotel will accommodate 105 men exclusive of hotel help and has all the conveniences of a city hotel."

Sep 1, 1925

By J. J. Bourquin, S. H. Katz

"Three types of respiratory apparatus namely, gas masks, hose masks, and self-contained oxygen-breathing apparatus - are now commonly used for protection from noxious gases, vapors, and smokes or ristes, but no particular type can be selected as best for all conditions. Many factors must be considered in connection with each situation, so that each must be considered as a problem in itself. Following are concise statements for comparing the types:Gas masks are the simplest and easiest to wear, also the least cumber-sore; but they protect only in comparatively low concentrations of noxious gases and should never be used where the air contains less than 16 per cent of oxygen. Special masks give protection from one gas or class of gases, but may give no protection against another gas or class of gases.Hose masks protect in any irrespirable atmosphere, but are somewhat cumbersome, the length of hose limiting the distance a wearer may go from fresh air. They are serviceable also where a supply of pure air moves with the wearer, as where a locomotive engineer in a smoky tunnel is using a hose mask supplied with air from the compressed air line of the locomotive. Hose masks consume no chemicals or materials and so are not limited in the time they may be used.Self-contained oxygen-breathing apparatus protect in any irrespirable atmosphere, but their weight is cumbersome, they can be used only by trained men, and frequent attention must be given them to maintain good working condition. On the other band they are the only safe means for exploring mines and other places filled with irrespirable gases in high concentrations."

Jun 1, 1923

By Uwe Kaulbars

Vibration measurements at the workplace are often complicated and expensive. The assessment of the risk in conformity with EC Directive 2002/44/EC “Vibration” (which lays down the minimum requirements of laws in Europe for occupational safety and health) can therefore be carried out on the basis of an estimate based on information from manufacturers as well as by measurement conforming to ISO 5349. The characteristic values (emission values) determined by manufacturers in laboratory conditions may deviate from the exposure values measured at source at the workplace. Equally, deviations may arise as a result of the delay in the changeover of test methods from the single axis of measurement to the total vibration value for the three axes of measurement conforming to ISO 20643. To prevent faulty estimates, the manufacturer’s information has to be corrected by a tool-related factor in accordance with CEN/TR 15350. By taking the example of masonry and stone working machines, the empirically determined tool-related correction factor is checked and confirmed. Methods Vibration measurements were carried out in accordance with ISO 5349 in practical application conditions on 10 selected typical eccentric and orbital sanders, concrete and disc grinders as well as on wall chasers and stone saws. Results The total vibration value obtained for the investigated tools rangedfrom ahv = 3.6 m/s² to ahv = 11.6 m/s². When the values from the practical measurements are compared with the manufacturer’s vibration values, the underestimation of the risk occurring in some cases can be largely compensated for by the tool-related factors conforming to CEN/TR 15350 (see Figure 1).

Jan 6, 2006

By Donald P. Schlick

This report presents a representative cross section of methods successfully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of ventilation on the water spray patterns of automatic sprinkler heads. Experiments were performed in a rectangular tunnel with pendent, upright, pendent sidewall, and horizontal sidewall sprinkler heads at air velocities of 0, 150, 300, 500, and 800 ft/min. As the air velocities were increased, there were significant shifts in the total coverage areas, density distribution patterns, and the maximum coverage densities for all types of heads. The pendent and upright heads exhibited upstream shifts in total coverage in the direction of the air-flow ranging from 4 to 6 ft, while the downstream coverage distances were extended up to 14 ft at the 800 ft/min airflow. The shift in upstream coverage distance for the sidewall heads ranged from 6 to 12 ft, while the downstream coverage was extended up to 22 ft at 800 ft/min. The results showed that airflow can have a significant effect on the coverage characteristics of automatic sprinkler heads and needs to be considered in the design of effective sprinkler fire suppression systems for ventilated areas.

Jan 1, 2010

By Thomas M. Barczak

he stiffness characteristics of longwall shields were investigated in this Bureau of Mines study. Since longwall strata activity is characterized by roof-to-floor and face-to-waste displacements, a model with two degrees of freedom was used to describe the load-displacement relationship of the shield structure. The model considers the support as an elastic body and relates horizontal and vertical resultant forces acting on the support to associated displacements as a function of the stiffness of the support structure. Stiffness coefficients under full canopy and base contact configurations were determined by controlled displacement loading of longwall shields in the Bureau's Mine Roof Simulator (MRS). Three two-legged longwall shields of different manufacture were investigated. The stiffness characteristics of these shields were evaluated relative to two parameters, namely, shield height and setting pressure. The test results indicate a reduction in shield stiffness for increasing height. Setting pressure was found to have less of an effect on shield stiffness, producing only a slight increase in stiffness as setting pressure increased. Similar trends were observed for all three shields, indicating a similarity in stiffness characteristics for shields of the same basic configuration.

Jan 1, 1988

By Clyde M. Pearce

The Lake Superior iron-mining district includes parts of the States of Michigan, Minnesota, and Wisconsin. The laws of each State provide for an industrial commission and for inspection of mines. The following extract from the General Orders on Mines, effective October 25, 1937, issued by the Industrial Commission of Wisconsin, is the only reference to the use of safety catches on mine cages or skips found in the laws and regulations in the Lake Superior iron-mining district: Order 316 - Cages for Hoisting Men. (c) Sides, Gates, and Safety Catches. ***Every cage shall be provided with safety catches of sufficient strength to hold the cage with its maximum load at any point in the event the hoisting cable should break. (d) Testing Safety Catches. The safety catches of cages and skips used to hoist men shall be kept well oiled and in good working order. They shall be tested at least once each month by tying up the cage or skip with hemp rope, lowering a few feet of hoisting cable on top of cage, then cutting the hemp rope, provided that any other system of testing, which is equally effective, may be used.

Jan 1, 1945

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By V. R. Spironello

Operating variables affecting the efficiency of the basic oxygen furnace (BOF) and the level of contaminating elements in the steel product were investigated by the Bureau of Mines. Steel was made in a 400-lb-capacity BOF designed to rotate on its vertical axis to increase the area of hot metal surface subject to oxygen attack. Hot metal for the BOF was made by melting pig iron and scrap in an 18-inch (ID) cupola. The variables were BOF speed of rotation, rate of oxygen flow, number of jets and angle at which they were machined into the oxygen-lance tip, temperature of hot metal, reactivity of lime, and temperature of scrap for the BOF charge. Experiments were arranged according to a two-level fractional-factorial design. The effects of the seven variables were evaluated for 13 responses. The greatest ingot yield occurred while using the larger angle lance tip and jets. The most carbon burned per unit volume of oxygen resulted from rotating the BOF and using the smaller angle lance tip. The largest sulfur transfer to the slag occurred at the higher hot metal temperature levels and higher rate of oxygen flow.

Jan 1, 1970

By E. J. Gleim

During the past 10 years the Bureau of Mines has had a broad experience in the tasting and inspection of electric motors for gaol-cutting machines, cowl drills, storage-battery locomotives and other equipment Which is used in mines where explosive mixtures of methane and air may be encountered. From this experience the Bureau's engineers have reached the conclusion that the most satisfactory method of protecting a motor so as to prevent any sparks resulting from rough commutator, loose contacts or short-circuits in it, from igniting he surrounding atmosphere, is to totally inclose the motor with a substantial casing; having flanged joints. These joints should be metal-to-metal contact so that the shortest path from the interior to the exterior Of the casing is not less than one inch in length. On account of this experience with mining machinery, the Bureau has been asked whether an equal or loss degree of protection would be sufficient for motors for service in or about places such as refineries, gasoline filling stations, cleaning establishments and pumping stations, or in any place where there is liklihood of explosive mixtures of gasoline or naphtha vapors and air accumulating.

Jan 1, 1922

By C. A. Herbert

"Haulage accidents usually are responsible for about 17 or 18 percent of all coal-mine fatalities and about 21 percent of all non-fatal coal-mine accidents. When the relatively small number of employees continuously exposed to haulage hazards is considered, it would appear that haulage is more hazardous than any other phase of coal-mine operation.Haulage accidents have increased from year to year, doubtless due to the increase in electrical haulage, and particularly to the use of larger cars, heavier locomotives, longer hauls, and greater speed. Unless very definite steps are taken to eliminate the causes of these accidents, they will continue to increase rather than be reduced, as they can and should be.Underground haulage in many of the large modern mines of today is similar in many respects to railroad practice. In recent years the railroads have made wonderful strides in reducing accidents, and instead. of being one of the most hazardous occupations, as it once was, railroading is now one of the safest. Doubtless, if thought and action, similar to that given to reducing accidents among railroad passengers and employees, were given to safety in mine haulage, under¬ground haulage accidents could be reduced in about the same ratio.Haulage accidents may be classified, according to responsibility, into two groups - those for which management is largely responsible and those for which the employee is largely to blame; there is, however, an overlapping of responsibility from one group to the other. If, therefore, haulage accidents are to be reduced, it is absolutely essential that both management and employees cooperate to this end.In the first group, for which management is largely responsible, may be included accidents due to faulty equipment, moor track, a poorly arranged system of haulage, lack of clearance or of overhead protection, and dirty roadways; even in these features, however, the employee is not without a measure of responsibility, as failure of haulage equipment possibly may be due to lack of care on his part, failure to report when equipment is out of order, or failure to do a good workmanlike job of installing or repairing or operating.To the second group of accidents for which the employee may be largely responsible, belong those caused by such careless practices as jumping on and off fast-moving trips, coupling on the ""fly"", running at excessive speeds, failure to properly block cars, and similar hazardous and unnecessary acts of omission or commission. If, however, management condones such practices, or, as in some instances, insists upon them, it must accept its share of responsibility for the accidents that inevitably result.Some of the most prolific sources of haulage accidents will be discussed briefly, together with the steps that may be taken to minimize their occurrence."

Oct 1, 1939

By Collin Stewart, Greg Hunt, Christopher Mark

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: • Roof bolt operators log the stratigraphy of test holes in nearly every cut. These “lith-graphs” are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. • Underground core drilling is conducted to obtain data for CMRR and stability maps. • Weekly “Quality” meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

By E. G. Valdez

Iron foundries that melt automobile scrap produce flue dusts averaging about 32 percent zinc and 6 percent lead. Some is sold to smelters, but because of the meager return and difficulty in handling, most of the dust is discarded. As part of the Bureau of Mines program to find uses for mineral wastes, research was initiated to develop an economical process to recover zinc and lead from the flue dust. Research encompassed the extraction of zinc and lead by fuming, leaching, and agglomeration. Controlled vacuum fuming of zinc to produce Prime Western zinc and a lead-rich residue was the most effective method for treating the dust. This process involved two distillations, or fumings, with carbon and methane as reductants, and resulted in recovery of 91.4 percent of the zinc in a Prime Western grade product, and 98 percent of the lead. Hydrometallurgical techniques involved several leaching methods, but the simultaneous extraction of iron, manganese, and copper resulted in contamination of the solution and made the zinc recovery processes too complicated. Agglomeration was done by pelletizing or briquetting the dust for possible use as feed to a zinc smelter.

Jan 1, 1975

By Doris M. Hyde

To a greater or lesser extent, the economies of the smaller Caribbean Island countries continued to have common problems. These included unemployment, inflation, foreign exchange shortages, trade deficits, and unstable world prices for their exports. Declining prices for petroleum provided some relief from scarce foreign exchange. Overall, the mineral sector remained stable. The Amerada Hess Corp. crude oil transshipment terminal on St. Lucia was completed during 1981. However, there were no shipments during the year. No official reason was offered for the delay in opening the terminal, but it may have been related to the world surplus of crude oil that occurred in 1981. There has been no further action on the refinery, which was to complete the island's petroleum complex. During the first half of 1981, an announcement was made that a second oil transshipment terminal would be built on St. Lucia. The report indicated that the terminal was to be financed by Saudi Arabia and include underground storage. After the original announcement, no further information was made available. This terminal, like the Hess petroleum complex, may have been temporarily postponed because of the crude oil surplus.

Jan 1, 1983