Search Documents

By Richard A. Thomas, Isaac A. Zlochower, Gregory M. Green, Kenneth L. Cashdollar, Martin Hertzberg

This paper reports the results of flammability studies for methane, propane. hydrogen, and deuterium gases in air conducted by the Pittsburgh Research Laboratory. Knowledge of the explosion hazards of these gases is important to the coal mining industry and to other industries that produce or use flammable gases. The experimental research was conducted in 20 L and 120 L closed explosion chambers under both quiescent and turbulent conditions, using both electric spark and pyrotechnic ignition sources. The data reported here generally confirm the data of previous investigators, but they are more comprehensive than those reported previously. The results illustrate the complications associated with buoyancy, turbulence, selective diffusion, and ignitor strength versus chamber size. Although the lower flammable limits (LFLs) are well defined for methane (CH,) and Propane (CA), the LFLs for hydrogen (HZ) and its heavier isotope deuterium (D2) are much more dependent on the limit criterion chosen. A similar behavior is observed for the upper flammable limit of propane. The data presented include lower and upper flammable limits, maximum pressures, and maximum rates of pressure rise. The rates of pressure rise, even when normalized by the cube root of the chamber volume (V 1/3), are shown to be sensitive to chamber size.

By Jr. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Laser-based instruments are used in areas where coal dust ignition presents a safety hazard. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory ~NIOSH, PRL! is conducting a study to help determine when an optical beam may be considered a potential ignition source in underground coal mines or coal storage facilities. Researchers conducted experiments to determine threshold igniting powers for Pittsburgh seam bituminous coal dust clouds using an 803 nm continuous wave laser. For fine sized coal dust dispersed in air, concentrations ranging from 600 to 2000 g/m3 were the most easily ignited. A heated layer of coal dust that deposited on the fiber tip during dispersion ignited the dust clouds. Minimum observed igniting powers for laser beams delivered by 200, 400, and 800 mm core fiber optic cables and directed into coal dust clouds were 2.0, 3.0, and 5.0 W, respectively. Threshold igniting power was proportional to beam diameter, and threshold igniting power density decreased with larger fiber diameters. Ignition delay times averaged 0.6 s and did not vary significantly with laser power under initially turbulent test conditions and with flammable targets. Comparisons are made with the results of other researchers.

By Ray J. Holmquist

"INTRODUCTION The Copper King or Red River copper mine was examined on December 13, 1942, by the Bureau of Mines at the request of Richard Kelly of Santa Fe, N. Mex. The examination was made to determine whether the expenditure of funds for rehabilitation work necessary to make the workings accessible for examination would be warranted.As a favorable report was made, the workings of the Copper King mine were opened and sampled under the direction of the author. The portal of the Copper King adit was opened first. Considerable rehabilitation was necessary in the first 50 feet of the workings, but the remainder of the drifts and crosscuts were sufficiently open to permit surveying and sampling.An attempt was made to open the Waterbury atilt, which was reported to be about 30 feet east of the Copper King portal, and to crosscut the ore body nearly to its southern border. However, slide rock and mine dumps had completely obscured the portal of this adit, and no opening into it could be found or made.Work on the project was started on September 27 and vas completed on November 6, 1943."

Apr 1, 1947

By Robert S. Sanford

This paper deals with truck haulage methods and costs at one of the many open-cut mines that are replacing rail haulage with heavy-duty trucks. At this mine, ore is trucked to a crushing plant, centrally located within one of the open-cuts. The requirements for efficient low-cost truck haulage are: Good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers The weighted average cost of hauling a long ton of ore to the crusher and the waste to the dump was reduced from $0.1993 in 1948 to $0.1114 during the last half of 1949, his corresponds to a cost per ton mile of $0.0864.

Jan 1, 1952

By Raymond B. Ladoo

The Bureau of Mines frequently receives requests for information on the mining , preparation and marketing of epsomite or Epsom salt , and in order to answer such inquiries the following information has been compiled . While it is probable that few people have considered epsonate as a mineral product , it will be noted that it should be so regarded and its production forms an important industry .

Mar 1, 1922

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991

By BUREAU OF MINES

The Bureau of Mines in its investigations of respiratory apparatus for use in mines and allied industries, tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum require- ments for safety in use. Approval certificates are issued for apparatus that meets the bureau's specifications, and the memfacturer is permitted to mark his equipment with a seal showing that it has been approved as "Permissible." A complete list of permissible self-contained oxygen breathing apparatus, gas masks, and hose masks tested before July 1, 1930, was published in Bureau of Mines Information Circular 6362.1 The present list includes all equipment tested and approved up to and including April 1, 1931.

Sep 1, 1931

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrogrephic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

By R. Karl Zipf, Z. T. Bieniawski

"SummaryAs part of an effort.to understand the mechanics of fine fragment formation in coal, which is important in studies of respirable dust due to mining, fracture toughness measurements and the strain energy density (SEO) theory were applied to calculate the crush zone size under a cutting tool in coal. This · zone is the major source of fine fragments in the 1 to 10 µm size range. The model used in these calculations is a boundary element program containing a failure criterion based on the SEO theory. The boundary element program calculates linear elastic stresses at numerous points in the coal material ahead of a cutting bit. These stresses arc then input to a subroutine called critical ftaw length and orientation (CFLO) which uses the SED theory to determine the CFLO for a small crack at the boundary element stress computation point. The extent of crushing is based on earlier postulates about . the role of inherent flaws in a fragmentation process. To form 1 to 10 µm fragments requires firstly a local stress strong enough to activate flaws with a characteristic length less than 1 to 10 µm and secondly, a flaw density sufficient to provide an average spacing between flaws also on the order of 1 to 10 µm. The locus of active lO µm ftaws represents the maximum possible extent of fine fragmentation in the 10 µm or less size range assuming that a sufficient inherent flaw density exists. The approach offers a first order approximation to the extent of crushing under a tool tip. The size and shape of the crush zone volume is affected by the attack angle and geometry of the tool.IntroductionFine fragment generation in the 1 to 10 µm size range under the action of a generic coal cutting tool may be explained on the basis of fracture mechanics which suggests two major sources of fine fragments: first in a crush zone near the tool tip and second by shear fracturing. along major macrocrack surfaces (Zipf and Bieniawski, 1988a). In this paper, fracture toughness measurements and the strain energy density theory are used to calculate the crush zone size. This zone represents the major source of fine fragments in the 1 to 10 µm size range and understanding the mechanical factors controlling its size represents a first step toward using fracture mechanics to characterize the ·tendency of various coals to produce undesirable fine fragments."

Aug 31, 1989

By Richard J. Mainiero

The U.S. Bureau of Mines in cooperation with Jim Walter Resources, Inc. (JWR), Brookwood, AL, evaluated the use of sheathed explosive charges in breaking up large stones that can jam the feeder¬breaker or pan conveyor on longwalls and halt operations. Use of the sheathed charge reduced the downtime of the longwall panel to 15 to 30 min as compared with the 1 to 2 h required to drill and shoot the stone. Firing the sheathed charge at the face caused no significant damage to Iongwall equipment. Use of the sheathed charge also represented an improvement in safety by eliminating the exposure of miners to the inherent hazards of the face for extended periods of time. Another benefit, which is difficult to quantify, is the elimination of the temptation to shoot mudcaps or adobes, which is illegal in U.S. underground coal mines.

Jan 1, 1990

By M. L. Williams

In recent years the use of visual aids has expanded the? field of safety education. This is a modern adaptation of a method employed in ancient times, when simple paintings and drawings were the only means of recording current events. In its present application, visual aid employs sound and silent motion pictures, stripfilms, lantern slides, descriptive posters, and color. According to Roberts,3/ "Visual education is a method of imparting information which is based on the psychological principle that one has a better conception of the thing he sees than of the thing he reads about or hears discussed." Dent4/ further defines visual aid as "all the materials used to facilitate the understanding of' the written or spoken word."

Jan 1, 1951

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are Likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrographic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of: present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic is examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was pub¬lished in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 392, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By G. L. Oldright

This paper is the first of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. ACKNOWLEDGMENTS The writers wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, to Mr. J. O. Elton, the general manager, and to Mr. A. B. Young, his assistant, for their broad-gauge policy that has made possible the securing and publishing of these data. For the staff at Tooele, acknowledgments are made to Messrs. B. L. Sackett, general superintendent, Carlos Bardwell, assistant general superintendent, S. Jacobsen, blast-furnace superintendent, H. M. Rockwell, assistant blast furnace superintendent, and J. O. Welsh, superintendent of the general research, for the spirit of cooperation they manifested in carrying out this work. Mr. C. Reish, a member of the research department, was detailed by, the company to assist in this' work and his whole-hearted assistance has been found invaluable.

Jan 1, 1929

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

By William C. Larson

A study was conducted by the Bureau of Mines to provide quarry operators with information regarding (1) the effects of jointing and bedding on rock fragmentation when bench blasting in two small-scale (2.5-ft) limestone benches, and (2) the successful use of inexpensive equipment and field techniques to determine the orientation and spacing of joints and bedding separations within the quarry. Using inexpensive equipment, such as a pocket transit and steel and paper tapes, joint and bedding separations were mapped and their frequencies measured. Results from two small-scale bench blasts in the Stewartville member of the Galena limestone formation showed that when the row of vertical blast-holes was oblique to the vertical joint orientations, the backface expression was outlined by two relatively large triangular protrusions (joint surfaces). In this blast, part of the rock burden was unbroken. When the line of vertical blastholes paralleled a predominant joint set, all of the rock burden was broken and displaced. The thickness of fragments that had been displaced by a blast correlated with the observed bedding thickness in the bench.

Jan 1, 1974