Search Documents

By D. Harrington

An explosive may be defined as a substance (usually a mixture) that has the property of yielding, readily to combustion or oxidation upon application of flame or shock, the combustion or oxidation process being rapid and accompanied by formation of such relatively large quantities of gases that much violence and pressure are produced; these, in turn, react against their surroundings and cause what is termed an explosion. By their very nature their action is destructive and disruptive of adjunct materials; hence, all explosives axe potentially hazardous and every type of explosive, irrespective of its relative safety, should be handled, .stored, and used with utmost care at all times and under all conditions. It should always be remembered that any explosive can be rude safe only in certain of its features and under certain conditions and circumstance. If these facts (and they certainly are facts) are always kept in mind, most of the modern types of explosives can be utilized advantageously in our industrial life and with a considerable degree of safety. That commercial explosives can be handled. safely is borne out in part by the fact that in the past 15 years at least 3,000,000,000 pounds of the commercial explosive dynamite have been transported by railroads in the United State, without injury to any person, insofar as available records indicate.

Jan 1, 1939

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

By C. B. Manula, R. L. Sanford, R. A. Rivell

A generalized flow diagram is presented in Figure 1, which shows the relationship of major model functions. This chart does not necessarily represent the anatomy of the computer program, but is designed to illustrate the informational interchange between major model functions. The related flow-charts-and computer program are listed in Parts I and II, Appendix A, respectively. Mine Car Stations The mine car stations are the activity centers for the model. The locomotive logic structure is designed to provide these stations with adequate cars and to clear them of car buildup. The model is designed to simulate a three stage haulage situation which suggests the need to differentiate station levels by type numbers. These are: a) TYPE 1 stations - mine cars are loaded here; b) TYPE 2 stations - intermediate stop and storage for mine cars; c) TYPE 3 stations - all mine cars that are stored here leave mine; and d) TYPE 4 stations - mine portal. TYPES 1, 2, and 3 have all loaded cars assigned to an ascending TYPE as their next destination. In input, if single stage haulage is designated, TYPES 1 and 3 do not exist, and if two stage haulage is called for, TYPES 2 and 3 are absent. A motor is not permitted to exchange cars between stations of the same type. Station Status Update. One major model function is to continuously evaluate the status of each mine car station. The major evaluations

Jan 1, 1974

By Paul E. Loustaunau, Devah Galloway, Catherine Wetherby

This report describes a project in which Development of a Supervisory and Management Training Program for the Underground Coal Mining Industry was developed and evaluated. The project was carried out in two phases. The first phase was a research effort to develop specifications for the program. The second phase was a development and evaluation effort. In the second phase, training programs for first-line supervisors (section foremen) and for middle managers (mine/shift foremen and mine superintendents) were prepared in accordance with the specifications and evaluated by members of the industry. This report describes the project and presents the conclusions drawn there from.

Jan 5, 1983

By J. S. Browning

The physical properties and specific gravity ranges of various liquids and salt solutions used for laboratory sink-float separations of rocks or minerals are presented. The test equipment and techniques employed by the Bureau of Mines in making sink-and-float separations of particles as coarse as 3 inches to as fine as 400 mesh are described. Also discussed are methods of recovering and reclaiming the liquids or salts from the minerals and wash solutions, as well as the hazards encountered and precautions to be followed while working with the materials. The laboratory use of various liquids for separating minerals of different specific gravities has been recognized for many years. During this time, laboratory sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations, such as those producing mica, spodumene, kyanite, and so forth. These procedures also have been used as analytical tools for determining the mineral content and associations of other metallic and nonmetallic ores.

Jan 1, 1961

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

The computer program has been developed in conjunction with the rest of the project to evaluate evacuation capabilities of the mines and develop guidelines for the escape systems. There are several problems associated with predicting evacuation performance of a mine. First, the mine has many interconnected passages, shafts, hoists and a number of miners in varying positions. To be able to predict evacuation time requires processing a hugh amount of data. A simplistic approach of determining the miner farthest from the exit and calculating evacuation time for him knowing his walking speeds and hoisting times is not realistic, since the waiting time for the hoist is neglected. The second problem is being able to repeat the calculations for a number of configurations. It may be possible to spend enough time to hand calculate the evacuation parameters for a single mine for a single configuration, but to evaluate capabilities of the evacuation

Jan 1, 1976

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By David E. Emerson

The Bureau of Mines has developed a mass spectrometer method for deter-mining the helium-3 content of high-purity helium. The work was performed to evaluate experimental methods for removing helium-3 from high-purity helium and to better determine the composition of pure helium used in research. This was accomplished by increasing the inlet sample pressure, ionizing current, and amplification of the current produced by the ions collected on a conventional mass spectrometer that had been modified. With these modifications, the helium-3 content was determined in the parts-per-million and parts-per-billion range in helium-4.

Jan 1, 1976

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

By Thys B. Johnson

A three-dimensional dynamic programing method is presented for determining the optimal ultimate open pit limit. The method given is based on the block concept and is an extention of the two-dimensional Lerchs-Grossmann approach. The three-dimensional technique presented herein is fast and simple and may be used for an initial open pit evaluation when only limited data are available or as a more refined model when the entire deposit is well delineated. The method is illustrated by simple numerical examples and is also presented in algorithmic form. A computer program was written in Fortran IV which implements the three-dimensional algorithm and some computational aspects are discussed.

Jan 1, 1971

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

By R. V. Ramani, B. K. Belle

The increased effectiveness of a two-phase spray system (TPSS) over a single-phase spray system (SPSS) for dust suppression is reported in several laboratory studies. The dust collection efficiencies of SPSS and TPSS were studied in a model experimental longwall gallery facility at Pittsburgh Research Laboratory at NIOSH (USA). The experimental design consisted of two factors: pressure, and airflow. Each factor had three levels. SPSS experiments were conducted at only one pressure (1035 kPa) which is nearly 1.5 times higher than the highest air and water pressure for TPSS experiments. The results of the study are presented in this paper. While it appears that TPSS performed better than SPSS, the data is not sufficiently conclusive on this aspect. The differing spray characteristics of the chosen TPSS and SPSS nozzles did not allow a direct comparison of the two systems. In the TPSS arrangement, considerably greater turbulence in airflow is created around the shearer; it is likely that at least in the immediate vicinity of the tailgate drum, there is a roll back of the dust/mist cloud into the walkway. Therefore, positioning of the personnel upwind of the tailgate drum is necessary to avoid high dust exposures. The rate of decrease in concentration with TPSS is higher than that with SPSS. This may be due to the greater atomization of the water. The test set-up did not allow the study of conditions when coal is cut from tail to head where the potential for personal exposure is high. Changes in the experimental design are necessary to overcome some of the reasons expected for the inconclusive results.

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986