Search Documents

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By Robert H. Schutz

This publication lists and describes devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, under the provisions of [§]70.300-1, Part 70, Subchapter 0 of Chapter I, Title 30, Code of Federal Regulations (35 F.R. 5548, April 3, 1970), for use as respiratory protection against respirable pneumoconiosis-producing dusts. Included are type C supplied-air respirators approved under Bureau of Mines Schedule 19R and dust, fume, and mist respirators approved under Bureau of Mines Schedule 21B.

Jan 1, 1971

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By G. E. McElroy

[During the period July, 1923, to April, 1924, we made a large number of careful determinations of the resistance to the passage of air in selected sections of airways in the metal mines of Butte, Mont. The experiments were conducted with the cooperation of the Anaconda Copper Mining Co., Frank D. Cannon, mining engineer of that company, and Fred P. Gaethke, mining engineer of the bureau, assisted in carrying out this work. This paper summarizes the, main group of data obtained in the form of a table, of friction factors, or coefficients of friction that is, values of K in the generally accented formula or air flow of [P = KSV or H = KSV2 ] where, in units customary to mining practice;]

Jan 1, 1925

Improve the dust control effectiveness of dry collection systems on surface coal mine drills. Approach Use a dust pelletizer to convert the respirable dust particles discharged by the dry collector into dust pellets that present no health hazard. Background Blasthole drills are well-known sources of respirable dust that can contain significant amounts of quartz. The drills frequently use a dry cyclone-filter type collector that can obtain dust reductions theoretically greater than 95 pct. However, surface mine drills using dry collectors typically have three major dust sources that significantly reduce the overall effectiveness of the collection system: (1) the dust collector dump cycle, (2) drill shroud leakage, and (3) leakage around the drill stem seal in the drill table.

Jan 1, 1989

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By Susan B. Bealko

Mining provides a large part of the energy and raw materials that feed this Nation&apos;s economy. Copper pipe, concrete, and window glass serve as well known examples of the reliance on minerals in modern society. Less appreciated, but as important, are the hundreds of mined commodities that are an integral and necessary part of everyday products, ranging from medicines and computers to carpet and paper. Coal is a major portion of the country&apos;s energy mix today, as it will likely continue to be in a future hydrogen-based economy. The domestic mining industry also provides strategic minerals that are important for the Nation&apos;s security. The processes to recover these mineral commodities are among the most demanding and complex in an industrial society, and this inherently dangerous industry has historically had the highest risks of fatality and injury. The mining industry has been undergoing some trying and challenging times because of the recent mine disasters in the coal fields. These events have been alarming in light of the strong and encouraging safety record that has characterized mining in the United States for most of the past decade. While mining communities deal with their grief, mine operators, government regulators, and other safety personnel, set about trying to determine why these fatalities occurred. Subsequently, the mining industry is currently experiencing changes in legislation at an unusually rapid pace. The most recent regulatory changes are the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) and the temporary emergency standard for mine seals. The new mine safety laws call on the nation&apos;s mines to adopt certain procedures and safety technologies immediately, or as soon as they become commercially available. Putting all the provisions in place from these new laws is a major undertaking, and will necessitate strong collaborations and partnerships among mine operators, manufacturers, regulatory and research agencies, labor unions, and community groups. It is against this background that Prevention through Design (PtD) components for the Mining Sector are recommended.

Jan 1, 2008

By Loyal Clarke, H. H. Storch

"The discovery of large deposits of polyhalite (K2S04.MgS04.2CaSO4.2H2O) in Texas has led to an investigation of possible industrial proecsses for the extraction of potash from this material. This mineral was first discovored in small quantities in the European potash deposits in or about the year 1800. Chemists fire thought it to be a form of calcium sulphate, but a more accurate analysis by Strohmiyer indicated the composition as given by the above formula.The decomposition of polytalite by aster is very slow and results in the formation of a layer of gypsum at the surface of the polyhalite which retarts the solution of the potaseium and magnesium sulphates. To obtain a substantial yield of K2S04 in solution it is necessary to use large amounts of water at room temperature, for he concentration of K2S04 is limited by the low solubility of syngonite (K2S04.CaS04.H2O) whereas at 100º C. several days boiling are necessary to obtain more than a 6 per cent K2S04 solution even when finely powdered polyhalite is employed.In 1854 H. Rose discovered that calcination, followed by leaching with water, resulted in a larger extraction of the potassium and magnesium sulphates, as compared with leaching without precalcination. During the course of a series of investigations concerning formation of oceanic salt deposits, Van't Hoff and his pupils obtained sufficient data to construct the equilibrium diagram for the system K+Mg+SO4--Ca++.H2O for 25° C. and for 83° C. These data are very well summarized. in the International Critical Tables' and by Boeke and Eitel. From a consideration of the diagrams for 83º C. one would conclude that an extraction of polyhalite with moderate amounts of water at 33º C. would result in a solution whose maximum concentration of K2So4 would be about 3.6 grams per 100 grams of water and of M2SO; about 4.0 grams per 100 grams of water, corresponding to equilibriumwith the solid phases: Polyhalite potassiam-calcium pentasulphate and anhydrite.The fact that it has been found possible to obtain as high as 11.4 grams of K2S04 per 100 grams of water (see table 6) and an equivalent amount of MgSo4 (8.1 grams per 100 grams of water was obtained corresponding to a ratio K2/Mg of 0.98; indicates that the formation of these complex salts is very slow. To be sure, this results was obtained at 100° C. instead of 83º C. However, the work of Anderson and Nestall 9 on the double salts of calcium and potassium sulphates at 100º C. indicates that the diagram at 100º C. C. would not be greatly different from that at 83º C. This slow rate of approach to equilibrium when combined with precalcination of,of polyhzli-,a is the 17,asis of some of the more p:olisinE methods of extracting potash from polyhalite."

Jun 1, 1930

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

By Kihong Park

A hygroscopicity tandem differential mobility analyzer (HTDMA) technique is used to determine size-effect of nanoparticles (NaCl, (NH4)2 SO4, KCl, NH4NO3, MgCl2,CaCl2) on their hygro­scopic properties (deliquescence relative humidity (DRH) and hygroscopic growth factor (GF)). The HTDMA system uses a combination of two nano DMAs and two regular DMAs to measure particle size change in a wide dynamic particle size range. Particles are subsequently analyzed with a transmission electron microscopy to investigate the potential effect of particle structure or morphology on the hygroscopic properties. We found that structural properties of NaCl and (NH4)2SO4 particles also play an important role in determination of the DRH and GF and are more pronounced at smaller diameters. Data show that the DRH of NaCl nanoparticles increased from *75% up to *83% RH at 8 nm and that their GF decreased with decreasing size. The extent to which the GF of NaCl nanoparticles decreased with decreasing size was greater than theoretically predicted with the Kelvin correction. The GF of furnace-generated NaCl nano­particles that have pores and aggregate shape was found to be smaller than that of atomizer-generated particles that are close to perfectly cubic. For the case of atomizer-generated (NH4)2SO4 nanoparticles, we observed no signi?cant size-effect on their DRH, and the measured GF agreed well with predicted values using the Kelvin correction. For furnace-generated (NH4)2SO4 nanoparticles, a gradual growth at moder­ate RH without noticeable deliquescence behavior occurred. Their TEM images showed that contrary to atomizer-generated (NH4)2SO4 nanoparticles the fur­nace-generated (NH4)2SO4 nanoparticles are not perfectly spherical and are often aggregates having pores and holes, which may favor holding residual water even in the dried condition. For atomizer-generated KCl, MgCl2, and CaCl2 nanoparticles, we observed no signi?cant size-effects on their DRH and GF for the mobility size as small as 20 nm.

Jan 1, 2008

By A. W. Maynard

Simple chemical spot tests for the identification of major alloying elements in aluminum-base alloys are described. The tests are suitable for use by nontechnical personnel working outside a laboratory. Tests for zinc, copper, manganese, and magnesium employ electrographic sampling methods and sample papers. Use of electrographic sampling in a test for magnesium in aluminum is made possible by using glass fiber filter paper. Differentiations between magnesium and magnesium-silicon alloys of aluminum and between aluminum-base and magnesium-base alloys are made by direct chemical solution tests. Description of a device for obtaining reliable electrographic samples is included. A sequence of testing for identification by alloy groups is given.

Jan 1, 1971

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector&apos;s response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the&apos; applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

Although haulage truck collisions account for only a small percentage of haulage accidents, the likelihood of severe injury, or even death is very high when such a collision does occur. Most rear-end collisions also result in considerable equipment damage, creating a need for expensive repairs. To improve collision protection, some southwestern surface mines have, for several years, been fabricating and using extended bumpers. In cooperation with these mines, the Bureau of Mines has worked to improve this technology by evaluating the structural requiremnts of extended bumpers. How Extended Bumpers Help The Bureau found that when one large rear-dump haulage truck collides with the rear of another an extended bumper protects the driver of the vehicle that is struck by dissipating the impact energy into the rear tires and pushing the whole vehicle forward. An extended bumper also prevents the box on the truck that is hit from penetrating the cab of the other truck-a typical and serious collision hazard. A further advantage derives from the wide design of the extended bumper which helps prevent damage to truck ladders, thereby minimizing any entry or exit problems. Extended bumpers also provide safe work platforms at the front of large haulage vehicles.

Jan 1, 1984

By M. K. Larson, J. P. Dunford, E. G. Zahl, T. M. Brady

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an on going effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for implementing a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. However, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

THIS PROGRAM TRANSFORMS FREE FORHATED BRANCH DATA INTO A FORMAT SUITABLE FOR INPUT TO THE PENNSYLVANIA STATE UNIVERSITY MINE VENTILATION SIMULATOR (PSU/HVS 1. BRANCH RESISTANCES ARE ASSUMED TO HAVE BEEN ALREADY CALCULATED, IIOWEVER THIS PROGRAM CAN BE EASILY MODIFIED TO HANDLE THE ADDITIONAL INPUT DATA REQUIRED FOR RESISTANCE CALCULATIONS IN THE PSU/MVSO THE PROGRAM IS WRITTEN IN FORTRAN IV WITH WATFIV.

Jan 1, 1977