Search Documents

By Charles Prasky

The objective of this investigation by the Bureau of Mines was to determine the response to sulfatization of diverse low-grade manganiferous materials in the iron formation of the Cuyuna district. In line with this objective a bench-scale sulfatizing procedure was developed that was less expensive and more rapid than pilot-plant methods. Samples from the central and south- western parts of the North range were tested. Results of evaluating a total of 46 pelletized samples, originating in areas with an estimated potential resource of 94 million long tons with a manganese content of 7 percent, indicates that approximately 87 percent of the manganese may be recovered as a synthetic manganese ore. This is equivalent to more than 12 million long tons of a metallurgical-grade ore, containing 46 percent manganese. It is anticipated that a premium product, containing over 50 percent manganese, may be obtained by sulfatizing procedures. This report is part of a continuing investigation5 6 of Cuyuna iron range manganese deposits in Crow Wing County, Minn. Lewis and coworkers describe the manganiferous iron formation in the bedrock of the Cuyuna district and include a description of a high-temperature differential sulfatizing process for recovering a ferrograde manganese product. The low-grade manganiferous

Jan 1, 1961

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

By Steven A. Fechner

The U.S, Bureau of Mines is conducting a four-year (1987-1990) study to assess the mineral resources and mineral development potential of the Valdez Creek Mining District in southcentral Alaska. This study is part of the Bureau's ongoing statewide mining district evaluation program. This report summarizes the Bureau's site specific evaluations of two areas (Tyone and Peters Creek) of the district that were investigated to determine the bedrock sources of gold and PCM in the alluvial gravel of both areas. In the Tyone Creek area, grains of gold (up to 0.0212 oz/yd3) and platinum group minerals (PCM) were recovered from alluvium and weathered conglomerate of the Jurassic Naknek Formation and Tertiary age using placer sampling techniques, Platinum and palladium were detected in the heavy mineral concentrates recovered from placer sampling the alluvium, and Naknek Formation and Tertiary conglomerates. In the Peters Creek area, grains of gold (up to 0.014 oz/yd3) were recovered from the alluvium and Tertiary Sterling Formation conglomerate. The Bureau's evaluations indicated that drainage basins containing conglomerate are the most favorable targets for placer gold and PGM exploration; and Tertiary conglomerate represents a high volume, low grade gold resource.

Jan 1, 2011

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By G. T. Fisher

The U.S. Bureau of Mines conducted research on calcium ferrite slags to determine the distribution of Pb and minor elements (Ag, Cd, Zn, and Co) between Pb bullion and slag. These fundamental data are required to evaluate nonferrous smelting with calcium ferrite slags as a substitute for conventional iron silicate slags. Determinations were made in 25-cm3-capacity MgO crucibles at 1,250° C for 2 h in a CO-CO2 atmosphere with an O2 potential that would retard the formation of magnetite. Calcium ferrite slag composition variables studied were from 16 to 32 wt pct CaO in 2-pct increments and Si02 ranging from 1 to 5 wt pct in 1-pct increments with equal additions of MgO. For all compositions studied, the retention of Pb in the calcium ferrite slag was less than 1 wt pct, which compares favorably to about 6 wt pct Pb in conventional iron silicate slags used in smelting of Pb concentrates. Minor element distribution was insensitive to changes in slag composition in the range studied. However, slag composition had significant impact on the melting and fluidity of the slag.

Jan 1, 2010

By James C. Barker

Alluvial cassiterite concentrations are widespread in river gravel and high level terraces within the Ray River watershed. The area lies in unglaciated terrain of Alaska's northern interior. Cassiterite originates from several calc-alkaline plutons of the Ruby batholith. Extensional stresses resulted in graben-like Tertiary basins that were flooded by a 200 ft thick section of mid-to late- Tertiary basalt flows. Basalt blocked local drainages, and 50- to 100-ft of terrace gravel was eventually deposited on top of the flows. Further downwarping and eventual fluvial downcutting of the flows resulted in cycles of accelerated sediment transport, deposition, and reconcentration. Repeated erosional cycles concentrated heavy minerals and resulted in development of tin placers. Preliminary resource estimates of contained tin in Recent alluvium range from 62 to as much as 172 million lbs-Sn in 300 million yd3. Grade of about 90% of the gravels is estimated to range between 0.2- to 0.5- lbs-Sn/yd3. Associated gold and rare earth elements (REE) in monazite and xenotime may be recoverable. Most of the tin is considered a subeconomic inferred resource, though, at least some of the gravels contain 2-to 6-lbs-sn/yd3. Estimates are projected on the basis of surface sampling and several auger drill holes and are provided for the purpose of land-use management planning.

Jan 1, 2011

By J. D. Kalasky, Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out- side headings of a set of five being developed in virgin area, and (2) conducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

By G. Schuman

Variations in pyrite reactivity are known to exist within samples collected from different areas. Using samples collected from acid and non-acid sites, the relationship between the factors affecting pyrite oxidation and observed variations in pyrite reactivity was studied. Heavy liquid separations were used to extract the pyrite from nine pulverized rock, coal, and coal refuse samples. Simulated weathering tests were used to determine the degree of reactivity of the extracted pyritic material. Representative portions of each pyritic sample were analyzed for whole rock composition (including pyritic sulfur and neutralization potential), for elemental composition, and by x-ray diffractometry. The samples were also examined with reflected light microscopy to ascertain pyrite morphology distributions. Tests for the presence of iron-oxidizing bacteria were all negative indicating the leaching tests were conducted under abiotic conditions. The results of the simulated weathering tests permitted the partitioning of the samples into two groups based on positive or negative neutralization potential (NP) values. Determinations were then made to evaluate the degree to which a variety of factors, including temperature, partial pressure of oxygen and water, and crystallography affected pyrite reactivity. Multiple regression analyses showed no statistically significant relationship between degree of reactivity and elemental composition. However, for samples with negative NPs, a simple regression analysis showed a strong linear relationship to exist between the reactivity of the pyrite and the proportion of "unstable" pyrite (framboidal + mossy pitted) found in each extracted pyrite sample. Samples of pyrite with positive NPs, although producing acidity, did so in at least one order of magnitude less than the NP deficient samples, indicating the important role that NP plays in controlling pyrite reactivity. A simple linear regression between cumulative sulfate production and NP for the three samples with positive NPs had a correlation coefficient of 0.99. For the nine samples grouped together, a linear regression model between cumulative sulfate production and NP (both negative and positive) was established between log of sulfate and NP.

Jan 1, 1991

By J. E. Wilson

The Pittsburgh carbonization laboratory of the Bureau of Mines has determined the expansion or contraction of more than 300 coking coals in a modified Bethlehem-type sole-heated expansion tester. Information on the actions of coals or blends of coals when coked is extremely valuable to operators of commercial-scale coke ovens. Coals that expand abnormally or beyond expectations can cause extensive damage to coke ovens and result in costly shutdowns and repairs. Although test results for many of the coals have been given in various Bureau of Mines publications, considerable information was not published. Thus, it is the purpose of this report to furnish coal operators and the coking industry with a current appraisal of the expanding properties of all coals tested by the Bureau before September 1, 1958. These data should be useful in the normal long range planning of coal and coke production and will be essential if the demand for coking coals increases abnormally or when reserves of higher grade coals are depleted.

Jan 1, 1959

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By Ervin P. Fuchs

Volume II of this report presents the vibration data, octave band data, one-third octave band data and narrow band (amplitude versus frequency) data for ten mining machines. These ten mining machines include a Goodman 968-2 Loading Machine, a Lee Norse 245 Continuous Miner, a Jeffrey 120L Continuous Miner, a National Mine Service 3080 Continuous Miner, Acme D-1 Roof Bolter, a Lee Norse 265 Continuous Miner, two Jeffrey Locomotives, a Joy CD-71A Coal Drill and a Jeffrey 100L Auger Miner. Volume J of this report presents the effects of underground environment and loading conditions on noise levels of coal mining equipment

Jan 1, 1979

By G. W. Birge, D. E. Wolfson, J. H. Lynch

This report presents all available 900 ° C BM- AGA carbonization and related data for coals from the principal beds of the southwest Virginia field in a form which permits ready comparison of product yields and properties of coals and cokes . Thirty- one channel samples from Buchanan , Dickenson , Russell , Tazewell , and Wise Counties were carbonized at 900 ° C in an 18 - inch - diameter retort . Blending properties of 10 of the coals were studied , and expansion of most of the coals and blends was measured in the Bureau of Mines sole - heated oven . Ash Most of the samples were chemically suitable for metallurgical use in coking blends , and their coking properties generally were satisfactory . content exceeded 10 percent in only three samples , and none of the coals contained more than 1.5 percent sulfur . Dry , mineral - matter - free fixed - carbon content of the coals ranged from 62.1 to 77.5 percent . Expansion behavior varied widely , ranging from 16.8 percent expansion to 27.6 percent contraction .

Jan 1, 1964

By Robert L. Jones

The Boston Consolidated mine is situated in the Bingham mining district, Salt Lake County; Utah (fig. 1). The property has had a noteworthy production of cupriferous, gold-bearing, pyritic ore in addition to lead ore. The Bureau of Mines established a diamond-drilling development project on the property in September 1943 with the primary objective of determining the continuity of a mineralized zone in the Commercial limestone below and to the northeast of the 800-foot level (fig.2). Examination of the geologic feature at the property previous to drilling indicated that the mineralized limestone horizon would continue belay the 800-foot level, but with a flatter dip than disclosed above this level. During the project period, 36 holes totaling 4,001 feet were drilled from underground stations outlining the zone below the 800-foot level (figs. 2 and 3).

Jan 1, 1949

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 per-cent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Delta summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1956 was made under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 120 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1956 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 17 producers of aviation jet fuels are represented.

Jan 1, 1957

By D. A. Reynolds, J. D. Davis

During early development of the blast furnace, Connellsville coke made entirely from Pittsburgh-bed coal proved to be an excellent fuel. The need for blending coking coals arose as the industry grew and it became necessary to carbonize coals having voking properties inferior to those of Pittsburgh coal Most coals carbonized today in continental Europe and this country are blonded: This practise has improved the quality of coke and permitted the utilization of coals that would yield inferior coke, if carbonized sepa- rately, The depletion of the world's better coking coals, which has been noted by leading coal technologists,2/4/wes accelerated during the recent war and. It is important, therefore, that reserves be evaluated and conserved. In the principal, steel-producing sections of this country, Pocahontas coals have been blended so extensively that the terms "low-volatile coking coal": and. "Pocahontas" have become virtually synonymous. Other low-volatile coals. have been used to manufacture metallurgical coke and will be used more extensively as, the supply of the better known and more accessible Pocahontas coals decreases. Recognizing the need for augmenting the supply of high-rank coking coals, the Bureau of Mines has included both low- and medium-volatile coals in its Survey of the Carbonizing Properties of American Coals, which was started with the cooperation of the American Gas Association in 1929. Twenty coals, 12 of low-volatile and 8 of medium-volatile rank, have been blended with high-volatile A Pittsburgh-bed coal, and five standard low- volatile coals have been blended with various high-volatile coals. Most of the results of carbonization tests of these coals and their blends have been

May 1, 1946

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007