Search Documents

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By Ernest Ph. Hérivel

The mine and treatment plant of the Teziutlan, unit of the Mexican Corporation, S. A., are located at Aire Libre, in the District of Teziutlan, near the northwest edge of the State of Pueblo, Republic of Mexico. The property is leased from the Teziutlan Copper Co. The town of Teziutlan is the terminus of a branch railroad starting from Oriental Junction or the Mexico-Jalapa-Veracruz narrow-gage system of the National Railways of Mexico. A branch line 18 km in length from Teziutlan to Aire Libre belongs to the Teziutlan Copper Co. and is leased and operated in conjunction with the mine.

Jan 1, 1933

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By J. J. Hoeppner

Accurate determination of moisture in coals of various ranks has long been a subject of intensive investigation. Excellent reviews of methods developed over many years are given by Brown (9)4/ and, with experimental comparisons, by Goodman, Gomez, and Parry (11). As pointed out in these and other writings, one of the principal difficulties in assigning absolute merit to one or another procedure is the multiplicity of conditions under which water may exist in coal and the difficulties involved in obtaining sharp separation and distinction between these classes. Gauger (10) states: Water recoverable from coal is obtained from the following sources: (1) Decomposition of organic molecules (sometimes called combined water), (2) surface adsorbed water, (3) capillary condensed water, (4) dissolved water, and (5) water of hydration of inorganic constituents of the coal.

Jan 1, 1956

By Edward L. Burwell

The Bureau of Mines conducted laboratory experiments to determine the change during retorting in the apparent permeability and the degree of compaction of beds of broken oil shale. Grades of oil shale studied ranged from 20.6 to 46.7 gallons of oil per ton (gpt), and the simulated overburden pressures applied to the shale were from 300 to 900 psi. Linear regression analysis of the data produced equations describing the response of the oil shale. Oil shales of approximately 20 gpt experience only minor apparent permeability reductions under test conditions, but richer shales (30 to 50 gpt) lose essentially all permeability. The permeability reductions were accompanied by corresponding decreases in bed height that ranged up to 37 percent of the original bed height.

Jan 1, 1974

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By H. Netuka, J. V. Horak, A. W. Khair

"A general review of major problems concerning mathematical modelling of roof bolting problem is given. A mathematical model (MM) of interactive set Bolt - Resin - Rock and its discretization based on the Finite Element Method (FEM) is developed to calculate numerically course of displacement, stress and strain fields in this set. This new MM enables to get also course of the normal and tangential components of contact stress vector, normal displacement and then mutual tangential slip at the bolt - resin and resin - rock interfaces, respectively.Behavior of system on all interfaces is modelled in the MM as a ""unilateral contact"" governed by so called non-classical boundary condition of Signorini's type including Coulomb's law of friction between resin and rock, and ""a given friction"" law between bolt and resin (see Duvaut, Lions (1972) for mathematical formulation).Numerical example and some values of resulting stresses are shown and remarks on necessary and sufficient conditions for solvability of the problem are also given.IntroductionAs is well known roof bolting has become the primary support system in almost all underground coal mines. But the ""theoretical"" design criteria for roof bolt patterns are rather problematic because: "" ... real mechanisms by which the roof bolts reinforce the immediate roof of underground coal mine entry are still relatively unknown"", see Peng (1986).The aim of this contribution is to present brief description of fundamentals of mathematical theory (see Hlavacek et al., 1988) which could be, according to our opinion and knowledge, very helpful for numerical modelling of a such type of problems. For the sake of brevity we restrict ourselves here to just one of the simplest possible problem: analysis of the behavior of interactive set composed by only single full - length - grouted bolt, resin (or cement) and suitable part of domain of a ""immediate"" neighborhood of bolt which should represent physical action of real rock material."

Dec 1, 1995

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant, presently producing coalbeds in Mercer County, W. Va. Approximately 650,000 tons of coal was produced in Mercer County, W. Va., in 1960, of which over 630,000 tons was cleaned in four preparation plants. In 1960 the Pocahontas Nos. 3, 6, and 11 coalbeds supplied 99.5 percent of the total coal mined in the county. Because the number of working mines In this county was small, only six samples were collected; four of which were of metallurgical quality as mined. The remaining two samples could be upgraded by washing at suitable specific gravities. Many of the samples taken were of metallurgical quality as mined; however, the float-and-sink analysis on these coals has been included to point out their amenability to the production of premium quality, special purpose coals. In general the coals were low-volatile bituminous in rank with low ash and sulfur contents.

Jan 1, 1963

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By K. O. Bennington

The thermodynamic properties of hedenbergite, of composition [(Ca0,9516) (Mg0,0583Fe2+0.7134 Fe3+0.0934 Mn0,1366) (Si206)], were experimentally determined at the Bureau of Mines. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -680.96±0.855 kcal/mol. The standard enthalpy of formation from the oxides is AR-96 = -24.55±0.485 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 12.3 to 300.1 K. The derived standard entropy is S-98 - 41.218±0.148 cal/mol-K. High-temperature heat capacities were measured with a differential scanning calorim¬eter from 397 to 1,147 K. These experimentally determined data were combined with data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation are given as a function of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -641.90±0.86 kcal/mol.

Jan 1, 1984

By Charles B. Kenahan

The chemical and galvanic corrosion properties of commercially pure titanium, a titanium-manganese alloy, a titanium-aluminum-tin alloy, 2 titanium-copper alloys, and 2 titanium-aluminum alloys were studied. Tests were conducted in synthetic ocean water, tapwater, 1-percent sodium hydroxide, 5-percent ferric chloride, and 5-percent ammonium sulfate solutions, various concentrations of sulfuric and hydro-chloric acids, and 1-percent oxalic acid. All tests were carried out at 35° or 60° C., with a flow of air or helium. Dissimilar metals involved in galvanic-couples experiments were aluminum, magnesium, and stainless steel. Electrode-potential measurements on single (uncoupled) specimens were also measured. Commercially pure titanium and the titanium-base alloys were generally quite similar in their resistance to corrosion, whether alone or in. contact with a dissimilar metal. Contact with the titanium metals caused aluminum and magnesium to corrode by galvanic action. Coupling with stainless steel in sulfuric acid solutions decreased the normal corrosion rate of the titanium metals. Contact with aluminum in air-aerated oxalic acid and 0.1N sulfuric acid solutions resulted in cathodic corrosion of titanium and the titanium-base alloys; however, there were a few exceptions. The copper alloys showed better corrosion characteristics than titanium in certain sulfuric acid solutions but were more susceptible to chemical attack in some hydrochloric acid solutions.

Jan 1, 1958

By Frank J. Wiebelt

As a result of the examination of many copper-zinc properties in the West Belt area of California, nine were chosen for exploration projects by the Bureau of Mines. This was part of the Bureau's wartime mineral-development program aimed at maintaining production of essential metals and increasing ore reserves. The properties explored were the El Dorado, El Dorado County; Copper Hill, Newton, and Gray House, Amador County; Constellation, North Keystone, and Collier, Calaveras County; and American Eagle and Akoz, Mariposa County. In addition to surface sampling and mapping, 41 holes, aggregating 18,134 linear feet, were diamond-drilled. Detailed results of the work done on all properties except the El Dorado and Akoz are given in this report. The El Dorado and Akoz were discussed in Reports of Investigations 3896 and 4144, respectively. Figure 1 is an index map showing the location of the mines covered in this publication.

Jan 1, 1951

By L. B. Pankratz, R. Barany, W. W. Weller

Experimental determinations were made of the heats of formation at 298.15 ° K of cuprous ferrite and cupric ferrite ; the heat capacity of cuprous ferrite was measured over the temperature range from 50 ° to 298 ° K and the entropy at 298.15 ° K was evaluated ; the heat contents of cuprous ferrite and cupric ferrite above 298.15 ° K were measured to 1,500 ° K and 1,100 ° K , respectively . These thermodynamic values were combined with other pertinent data to obtain heat and free energy of formation values at high temperatures . The stability of the two ferrites with respect to their constituent oxides is discussed . Thermodynamic values are included for the decomposition of cupric ferrite to form cuprous ferrite , magnetite , and oxygen .

Jan 1, 1964

By M. B. Bransford

A calculation procedure was evolved by the Bureau of Mines for determining the heat-transfer characteristics of dilute gas-solid mixtures in an externally heated tube. The procedure accounts for differences in gas and particle velocities and covers a range of particle sizes. Heat transfer coefficients obtained by the calculation procedure are compared with values reported in the literature.

Jan 1, 1970

By Clarence Hall, S. P. Howell, W. O. SNELLING

The explosives used in coal mines not only occasion accidents such as occur in the use of explosives elsewhere, but they frequently cause widespread disasters by igniting explosive mixtures of mine gas and air and of coal dust and air, or both. In addition, the firing of ex- plosives so shakes the walls and roofs of the mines as to cause falls, with their attendant casualities. Considering the large number of explosives and their wide range in composition and properties, it is obvious that certain of them should prove more suitable for use in coal mines than others. The problem is to determine which explosives are the most suitable for this purpose and the precise conditions under which they may be used with the greatest safety. Of course this problem could be worked out in actual mining, but experimental investigations when accompanying commercial opera- tions are hazardous and slow. To obtain the information sought, in the speediest and most economical manner, laboratory methods must be resorted to. The adoption of such methods began about 30 years ago with experiments in an iron gallery mounted on wheels, at Zwickau, Germany. This laboratory method of attacking the prob- lem has so commended itself that it has not only been repeated else- where in Germany but has at intervals been officially adopted, with many modifications and additions, by the Governments of Belgium, Austria, France, and Great Britain. Such was the status of coal-mine investigations in Europe when in 1904, an organization in the Geological Survey, which in 1907 be- came the technologic branch, was created to investigate the mineral- fuel resources of this country. At that time no division of the Na- tional Government had official cognizance of conditions existing in our mines, but through its system of collecting fuels for tests the technologic branch was forced to recognize that coal-mine accidents are a factor that must be reckoned with in determining the extent and availability of our mineral-fuel resources. This became so apparent, and it was so obviously a function of this branch to make a systematic research as to the cause and prevention of such acci- dents, that in July, 1907, experts were appointed especially to deal with this problem. As a result, not only was Bulletin 333, on Coal- Mine Accidents: Their Causes and Prevention, prepared and pub- lished, but through personal inspection of foreign testing stations, and a study of their reports and the critiques of their methods and operations, definite plans for the establishment of such a testing station in this country were formulated. In the latter part of 1907, four grave disasters occurred in close succession consequent on explosions in the Monongah mines in West Virginia, where 368 men were killed, the Darr mine in Pennsyl- vania, where 160 were killed, the Naomi mine in Pennsylvania, where 34 were killed, and the Yolande mine in Alabama, where 61 were killed. These frightful disasters so quickened the public con- science, and so plainly demonstrated that both humanitarian and economic needs demanded that steps be taken to prevent the re- currence of such accidents, that in 1908 Congress made a special appropriation for an investigation as to the "causes of mine ex- plosions." A similar appropriation was made in the following year. By act of May 16, 1910, the Bureau of Mines was created "to make diligent investigation of the methods of mining, especially in relation to the safety of miners, the use of explosives, the prevention of accidents," and other matters relating to mining. Therefore, these investigations are at present conducted in obedience to an organic act instead of being dependent solely upon special appropriations. The first appropriation became available July 1, 1908. Through the courtesy of the War Department a portion of the grounds and buildings of the arsenal at Pittsburgh was granted for the use of the technologic branch of the United States Geological Survey. Work was immediately begun in procuring and erecting the necessary instru- ments and appliances for carrying out the desired tests and inves- tigations and in adapting the existing buildings or in erecting new structures to contain the apparatus. The Pittsburgh testing station was officially opened and regular work was commenced on December 3, 1908, the apparatus and appliances having been tested, the force drilled in their use, and the equipment and methods inspected and passed upon by foreign experts.

Jan 1, 1912

By W. M. Deaton

The Keyes Helium Plant of the Federal Bureau of Mines was constructed under an expedited schedule, to supply the urgent and growing demand for helium in atomic energy, missiles, aerology, space exploration, shielded-arc welding, and low-temperature research. Construction began in December 1958 and ended in August 1959. The plant, near Keyes, Okla., processes 2 percent helium-bearing natural gas from the Keyes gasfield. In 1960 the plant produced and shipped 263 million cubic feet of helium (equivalent to an annual rate of 290 million cubic feet). Production cost was $9.11 a thousand cubic feet of helium. A low-temperature process involving two steps is used; the first separates a crude-helium product from the natural gas at about -250° F. and 225 pounds per square inch gage (p.s.i.g.); and the second purifies the crude helium to a high-purity product (Grade-A helium, 99.995 percent helium) at about -320° F. and 2,750 p.s.i.g.

Jan 1, 1961