Search Documents

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By D. C. Dahlin

The Bureau of Mines has investigated podiform chromite deposits in three ultramafic bodies in the Caribou Mountain and lower Kanuti River areas of central Alaska. The investigation, reported in two parts, was done as part of the Bureau's mission to help insure an adequate supply of minerals to meet the Nation's needs. Part I describes an extensive field investigation and mineralogical studies by personnel from the Bureau's Alaska Field Operations Center. This report, part II, describes the mineralogy of 11 samples that were high-graded from surface exposures at 10 sites and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The 11 samples, peridotites and chromitites that consisted of variable amounts of chromite or chromium-bearing spinets, olivine, and serpentine, were beneficiated by grinding and sizing, gravity concentration, and electrodynamic separation. Three high-chromium chromite concentrates, two high-iron chromite concentrates, and one high-aluminum chromite concentrate were produced. Three other concentrates were marginal, and two were submarginal. Chromium recoveries ranged from 54 to 92 pct. These results indicate that the areas may be significant chromium resources. Potential platinum association with the chromite was also investigated. Analysis of these 11 samples indicates that the areas are not good platinum resources.

Jan 1, 1983

By James P. McGee

Use of nuclear reactors to furnish high-temperature heat is a field that has not received as much attention as propulsion and electric power production. Investigations are being conducted under a joint Atomic Energy Commission (AEC)--Bureau of Mines research program to determine the feasibility of using nuclear heat for chemical processing. A part of this process-heat-reactor program is the study of a system in [hich] helium transfers heat from 8 nuclear reactor to a chemical processing [essel]. This requires construction of (1) a nuclear reactor to operate with helium exit temperature of 2,500° F. and with pressures in the range of 250 to 500 p.s.i.g. and (2) a processing vessel (heat exchanger) to convert the enthalpy of the helium into chemical process reaction heat. Neither component exists at present, and development of each promises to be a formidable task. To aid in the study of such a system, the Bureau of Mines has designed and constructed a vessel heated by electrical induction to simulate a source of nuclear fission heat. This vessel is undergoing preliminary testing. Gasification of coal and reforming of hydrocarbons are promising uses for nuclear heat. It appears that a higher price per unit of nuclear heat can be tolerated for chemical processing than that allowable for power generation.

Jan 1, 1960

By Leland E. Paulson

This investigation examined the feasibility of altering the inorganic component of North Dakota lignite by ion exchange. Lignite of specific size consist was washed with various ionic solutions and examined for evidence of exchange. Ions of higher valance substituted preferentially at equivalent concentrations. Results indicate that a major portion of the inorganic material associated with lignite is combined in exchangeable form with the organic component. Particle size of the treated coal is a critical factor in determining the rate of exchange. The data indicate that monovalent ions are easily replaced by divalent and trivalent ions, and the presence of ionic material in slurries containing finely divided lignite significantly increases filtration rates.

Jan 1, 1968

By J. G. Donaldson

A bench-scale method for recovering lead and zinc from slimes and mill tailings from the Tri-State District of Missouri, Oklahoma, and Kansas was developed by the Bureau of Mines. Dilute hydrochloric acid, containing sodium chloride, and chlorine gas were used to decompose the mineral constituents. Lead was electrolyzed from the pregnant acid solution, and zinc was precipitated from the depleted electrolyte by neutralization with lime. Up to 98 percent of the lead was recovered in an impure lead electro- deposit assaying approximately 85 percent lead. Zinc recoveries up to 90 percent of the total were attained in a precipitate assaying approximately 40 percent zinc.

Jan 1, 1963

By F. S. Crawford

A large number of operators of various industries in the United States do not appear to realize the great returns in dollars and cents which result from intelligently directed safety work . Managers of co 1 mines , metal mines , open-pit mines , quarries , steel mills , cement mills , oil rei meries , iron works , or other industrial operations , should by all means realize the great waste resulting from accidents , in order to appreciate the necessity for a continuous accident -prevention policy . While the prevention of accidents is worth while from the humanitarian standpoint alone , it has an equally important economic side , and before our mining industrial operations will be made as safe as they should be , it is apparent that this dollars and cents viewpoint must be given full recognition in order to bring before many of the men who run the industries the great importance of this phase of industrial management . : There is a tendency upon the part of the opera or who has not given thought to the cost of accidents ( and there are many mining operators of this type) to insure his company against compensation losses and against catastrophes for which he can secure insurance , and think he has done his duty ar an executive . Even though industrial operations were not compelled to pay compensation , and even if the management were not moved by humanitarian motives to try to stop accidents , it would pay many times over to carry on accident prevention work vigorously and continuously. : In some parts of the United States , the state compensation and insurance requirements are such that the operator does not receive a reduction in his insurance rate per men employed upon having made safety installations or upon having achieved a reduction of accidents in his plant . Under such conditions the management frequently does not feel encouraged to emert much effort in bettering the accident rate . However , when the responsible officials of a company realize the much greater harm to an operation which results from doing no accident - prevention work , and the great benefit in reduced costs which usually follows effective safety work , they should be inclined to do almost everything possible to reduce accidents , regardless of considerations as to accident compensations . There are enough indirect costs resulting from accidents to wreck many types of business ; excessive accidents result in disorganization and failure , while immunity from accidents usually means a smoothly running efficient organization .

Sep 1, 1930

By Kevin Malone

Chrysotile asbestos occurs in many counties in California, and a small production had been reported at times, but development of deposits had been disappointing. A reconnaissance survey by the Bureau of Mines indicated that several deposits in the serpentine belt in Shasta, Trinity, and Siskiyou Counties might contain enough asbestos of filler grade to supply the growing demand on the west coast. Accordingly from 1956 to 1958 parts of the Mount Eddy and Shasta View deposits were investigated by trenching and diamond drilling to determine their potential. The work comprised construction of roads, bulldozer trenching, excavation of areas for diamond drilling, sampling, and upping. The trenches were excavated to expose the surface extent of some of the asbestos-bearing areas, To determine the downward continuation of asbestos-bearing sections and to secure samples for test purposes, six diamond drill holes, totaling 1,738 linear feet, were drilled in two selected areas. The trenching and core-drilling indicated that the asbestos-bearing material occurs as ribs and lenses of varying thicknesses in a broad belt of serpentine, about 600 feet wide and several miles long,

Jan 1, 1962

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By M. M. Kirk

Forced-air cooling of cold-mold arc furnaces for melting zirconium and similar metals has been investigated and found to be practical from the stand-point of heat transfer. It is believed that this technique offers a significant reduction in explosion hazard from that inherent in water cooling, the current industrial practice. A copper crucible, with longitudinal, integral-type fins and with an outer jacket to confine the airstream, appears to be the best general design for air-cooled operation. Cutting the fins into short segments and bending the segments to produce a herringbone effect increased the airstream's turbulence and was found, on test, to increase the heat transfer up to 35 percent.

Jan 1, 1959

By Curtis D. Edgerton

Miami Oölite limestone is the only significant construction mineral in southeastern Florida. Its source area coincides with that of rapid urban expansion. Two-thirds of the existing resource is already unavailable because of development. Land-use conflicts place future availability of limestone in jeopardy. However, a sufficient limestone resource to meet demand for many years is present if its extraction is not restricted. Adverse environmental effects of quarrying Miami Oölite are not severe; land values often increase following quarrying. Future availability depends upon--(l) achieving uniformity of Federal, State, county, and municipality statutory requirements governing quarry operations; (2) setting aside specific land areas for future quarrying; and (3) cooperative planning to provide for land utilization upon completion of quarrying.

Jan 1, 1974

By V. F. Parry

[Approximatel~r 7-1/2 illion tOlls of subb1tnminous coals are mined an-nuall in Colorado, Wyo~ing, and Montana, of which 50 percent probably reaches dome ,-tic conswno:os. r:L'he moi s t'_re of the se subbi t1.Uninous coal sis high, averae;:t.:ug about 25 :!,)ercent \-Then they are :nined. T'ne coals are non-caking d ~~ack to a vari ble degree when exposed to nornal atmospheric conditions. ~hey a~e gpod domestic fuels, are considered to be smokeless in most furn~ces, and have been used. f, r f!1an: y ars in hand-fired domestic furnaces in hich tnc practice i~ to e~ploy large lureps for efficient com-]

Jan 1, 1941

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado's coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen's compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By Robert W. Metcalf

Since the spread of the European war virtually cut off imports from Denmark, Belgium, and France, the Bureau of Mines has had numerous inquiries as to domestic sources of grinding pebbles and silex or other types of ball mill liners. USES Flint pebbles and tube-rill liners are used by grinders of certain ceramic materials to prevent contamination of the finished product by iron abraded from steal baler and liners. The feldspar industry is one of the largest users of flint grinding mediums; they are employed also by curtain grinders of talc and soapstone, ground sand and sandstone, quartz, and chalk. Some paint materials, such as lithopone, have been ground in pebble Flint pebbles have been used more or less in the past, especially by cement manufacturers, and, for fine grinding of gold, copper, or other ores in which iron contamination is not especially deleterious.

Jan 1, 1940

By T. H. Jeffers

To help maintain an adequate supply of minerals to meet national, economic, and strategic needs, the Bureau of Mines investigated the feasibility of extracting copper from coarse native copper ore with ammoniacal ammonium carbonate solution by a simulated in situ leaching procedure. A 5.9-metric-ton (6.5-ton) sample of minus 30.5-centimeter (12-inch) conglomerate-type ore analyzing 1.96 percent copper was leached in a column for 556 days with a solu-tion that contained, in grams per liter, 2.2 NBs and 1.9 CO[3=]. The copper extraction was 71.4 percent, and reagent consumptions were, in kilograms per metric ton of ore, 1.1 NBs and 0.85 CO[3=] (in pounds per ton of ore, 2.2 NH3 and 1.7 CO[3=]). The pregnant leach solutions contained about 1.4 grams per liter copper, which was readily extracted from these low-tenor liquors with a 1:19 mixture of an organic extractant and kerosine. Copper was stripped from the loaded organic with depleted electrolyte containing 150 grams per liter H2S04, and the copper was recovered by electrowinning with antimonial lead anodes. Conditions also were established for minimal lead transfer to the cathode copper.

Jan 1, 1979

By W. L. Crentz

Before Korea was partitioned along the 38th parallel following World War II, the coal fields of South Korea, with the possible exception of the Samchok area, were not considered important to the industrial needs or Japan or Korea. Much of the demand for electric power in South Korea was met by hydroelectric installations north of the 38th parallel. Following cessation of hostilities between Japan and the' Allied nations in 1945, hydroelectric power continued to flow into South Korea from the north until 1949, when the North Koreans severed the power lines into South Korea, thereby forcing that section of the country to depend almost entirely upon coal to generate electric power.

Jan 1, 1953

By R. L. Marek

[An important problem in the efficient conduct of industry is that of helping the individual employee to formulate in attitude toward his work which will result in the reduction of accidents and the promotion of safety. Perhaps nowhere is the need greater for this type of psychological training of carefully selected men than at oil refineries whore both the raw materials and the finished products are highly inflammable and explosive in nature. However, the refinery organization usually is well adapted to educational safety activities -- much more so than in the producing, pipe line, and marketing departments where the personnel are more or less scattered; but the sore general principles of conduct hold true in any industrial organization. This problem of directing the attention of tie employees to their specific tasks or helping them to control and frequently eliminate hazards engendered by adverse mental attitude or emotion is met most satisfactorily by carefully selecting applicants and placing theta at jobs for which their ability best fits them. The subsequent training of these carefully selected employees to assure their Most effective work in accident prevention may be accomplished in a variety of gays, ouch as by personal supervision and instruction, inspections, drills, and by the studied use of well thought out safety pamphlets and posters.]

Jan 1, 1932

By R. L. Marek

An important problem in the efficient conduct of industry is that of helping the individual employee to formulate an attitude toward his work which will result in the reduction of accidents and the promotion of safety. Perhaps nowhere is the need greater for this type of Psychological training of carefully selected men than at oil refineries whore both the raw materials and the finished products are highly inflammable and explosive in nature. However, the refinery organization usually is well adapted to educational safety activities - much more so than in the producing, pipe line, and marketing departments where the personnel are more or less scattered; but the same general principles of conduct hold true in any industrial organization. This problem of directing the attention of the employees to their specific tasks or helping them to control and frequently eliminate hazards engendered by adverse mental attitude or emotion is met most satisfactorily by carefully selecting applicants and placing them at jobs for which their ability, best fits them. The subsequent training of these carefully selected employees to assure their most effective work in accident prevention mu be accomplished in a variety of ways, such as by personal supervision and instruction, inspections, drills, and by the studied use of well thought out safety pamphlets and posters. This procedure is simple in outline and not original in scope, yet the importance of selecting and training the personnel has, not been generally accepted by the petroleum industry until recent years. In 1926, the Bureau of Mines, while making a study of accidents in the petroleum industry, found that medical examinations of prospective employees were not receiving unanimous endorsement by all companies, and the point was stressed that the selection and allocation of employees was a problem requiring serious consideration in the petroleum industry.

Jan 1, 1932