Search Documents

By W. H. Blackburn

This paper describing the milling practice at the Tybo concentrator is one of a series of similar papers being prepared by the United States Bureau of Mines on milling methods and costs at the various mills in the United States. ACKNOWLEDGMENT A large part of this paper way prepared by H. M. Lewers, mill superintendent of the Tybo plant of the Treadwell Yukon Co., Ltd.

Jan 1, 1931

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By F. B. Petermann

Two-stage electric smelting tests, using small submerged arc furnaces, were made on high-iron manganiferous materials from the Pioche District, Nev., and the Cuyuna Range, Minn. The object was to reduce sufficient iron in the first stage to give a slag with a favorable Mn to Fe ratio for smelting to ferromanganese in the second stage. The nodulized flotation concentrate from the Pioche District contained 29.2 percent Mn and had a Mn to Fe ratio of 2.3:l. When smelted with coke and silica or alumina as flux, more than 90 percent of the manganese was recovered in slags with Mn to Fe ratios of 10: :24:1. The Pioche slag was smelted to ferromanganese using coke and lime- stone or dolomite as flux. The ferromanganese was high in silicon but other- wise met specifications. Recovery of manganese to ferromanganese in this step was 73 to 78 percent. Overall recovery of manganese was about 70 percent. The sintered flotation concentrate from the Cuyuna Range material contained 12.9 percent Mn and had a Mn to Fe ratio of 0.3:1. When smelted with limestone as flux, about 83 percent of the manganese was recovered in a slag with a Mn to Fe ratio of about 6:1. The Cuyuna slag was smelted to ferromanganese with coke and limestone for flux. Recovery in this step was 61 percent of the manganese in a high silicon ferromanganese. Overall recovery of manganese was about 50 percent.

Jan 1, 1963

By Lawrence G. Houk

In modern warfare mica is truly indispensable. The coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives such as splittings and films are also excluded from discussion. The paper therefore relates solely to block mica of strategic quality.

Jan 1, 1942

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The Objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By H. E. Harris

An extensive experimental program was carried out to determine the variability of respirable dust samplers and to determine whether area dust sampling is feasible in coal mines. For sampler variability, it was found under laboratory conditions, that a single dust measurement could be as much as 0.30 mg/M3 from the true value at the 95% confidence level. Under actual underground mining operations, this difference could be as much as 0.52 mg/M3 in the 0 -5.0 mg/M3 range. The results from dust sampling on 175 production shifts involving over 2,500 on-man and area dust samples showed that area sampling is viable, but the field investigation did not establish necessarily where the best area locations were.

Jan 1, 1976

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By J. Fletcher Smoak

Consumption of abrasive materials in the United States in 1981 was approximately $340 million, of which 37 % was industrial diamond (natural and synthetic), 39% manufactured abrasives, and 24% natural abrasives. Production and shipments of natural abrasives, excluding emery and industrial diamond, decreased in quantity 9% and 7%, respectively, when compared with that of 1980. Emery showed the largest change in output, decreasing 30% in quantity and 20% in value. Production of nonmetallic .manufactured abrasives material plus shipments of metallic abrasives material decreased 5% in quantity but increased 4% in value. Nonmetallic manufactured abrasives consisted of aluminum oxide (fused) and crude silicon carbide produced in the United States and Canada and accounted for 63% of the value of all manufactured abrasives. Metallic abrasives shipments included chilled and annealed iron shot and grit, steel shot and grit, plus cut wire, aluminum, and stainless steel shot and equaled 37 % of the value of all manufactured abrasives.

Jan 1, 1982

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By W. M. Merritts

The control of coal dust created and released during the operation of continuous mining machines in bituminous-coal mines of the United States is a problem. The interest manifested in this problem indicates the seriousness of the hazards involved, particularly when the dust has not been abated at its source and has become air-borne. Officials of the Sunnyside No. 1 mine, Kaiser Steel Corp., were confronted with the problem of abating the coal dust created by operation of a recently installed continuous-mining machine, and they requested the aid of representatives of the Coal-Mine Inspection Branch, Bureau of Mines, United States Department of the Interior, in developing an effective method of allaying the coal dust at its source.

Jan 1, 1951

By R. Hogg, S. Chander

"The distribution of the wettability of coals of different rank was determined by measurements of contact angles for individual particles. The contact angle was estimated from the equilibrium partitioning of a particle at the water/air interface. Using this technique contact angles were determined for a larger number of particles from a given sample and a frequency distribution of contact angle was obtained. The contact angle distribution was broad for all the coals tested with included an anthracite, a hvA bituminous and a sub-bituminous coal. In comparison, spherical particles of polymethylmethacrylaie gave a much narrower distribution. The distribution for irregular polyethylene particles was somewhat broader than that for the polymethylmethacrylate spheres but broader than that for the polymethylmethacrylate spheres but considerably narrower than that for coal. The broader wetting distribution for coal was attributed to differences in surface chemical properties.INTRODUCTIONA knowledge of the wetting properties of coals is very useful in coal cleaning by flotation and other processes in which separations are based on differential surface properties. The various methods available for measuring wetting characteristics include: contact angle, 1-2 time, time, 3-5 bubble attachment, 6 film flotation,7 displacement pressure, 8-9 penetration rate, 10-11 bubble pick-up, 12 induction time, 13 imbibition time, 14 and calorimetry. 15-16 Of all these methods, however, the measure¬ment of contact angle by the sessile drop and captive bubble techniques have been most widely used. Brady and Gauger"" demonstrated through the use of the contact angle method that the natural hydrophobicity of coal varied greatly from sample to sample. Subsequent experiments showed that this difference correlated well with rank, the larger contact angles generally being associated with the higher rank coals. 18-19 More recent studies by Aplan and co-workers' show that the wettability of various ranks of coals as determined by sessile drop and captive bubble methods is a more complex function of rank. The hydrophobicity of coal usually increases with rank up to about 80% fixed carbon (dmmf) and then decreases."

Mar 1, 1992

By Joseph P. DuCarme

The U.S. Bureau of Mines explored new methods and technology for extracting coal from the Appalachian Mountain region of the Eastern United States. These methods were aimed at extracting coal from thin seams and focused on the use of "roof-fall-tolerant" (RFT) mining concepts. These methods could be used on existing, abandoned highwalls or in conjunction with new highwall mining. The research was conducted using small-scale and quasi-full-scale physical models to obtain experimental results. Details are provided on (1) the quasi-full-scale model for cross-ridge mining, (2) the quasi-full-scale model for down-ridge mining, (3) the test results of these models, and (4) recommendations for future research. Significant results include demonstration of the RFT concept, a discussion of expected coal produced from these methods, and recommendations for future research.

Jan 1, 2010

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By J. William Ganser

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically palled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Fred Burkett, civil engineer, and F. O. Londrey, chief clerk, of the Trinity Portland Cement Co., for assistance in preparation of this paper, "The Geology of Dallas County. 1918," Bulletin 1818, Texas Geological Survey, Austin, Tex., by E. W. Shuler, was also freely consulted.

Jan 1, 1931

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

In 2007, a total of 14,871 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.4%) were sand and gravel mines, followed by stone mines (31.2%), coal mines (13.7%), nonmetal mines (4.9%), and metal mines (1.9%).

Aug 1, 2009

In 2004, a total of 4,401 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.4% of all mining operations.

Sep 1, 2007