Search Documents

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By Office of Public Information

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable.·This issue of the Bureau of Mines. List of Publications and Articles describes reports and articles published during the period January 1, 1985, to December 31, 1989. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;2 the 5-year lists of publications and articles from January 1, 1960, to December 31, 1964,3 from January 1, 1965, to December 31, 1969,4 from January 1, 1970, to December 31, 1974,5 from January 1, 1975, to December 31, 1979;6 and from January 1, 1980, to December 31, 1984.7"

Jan 1, 1990

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking focused the attention of the Bureau of Mines on the need for safety standards For such operations. Information Circular 7810 was published to meet that need. The current revision updates and replaces IC 7810. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1968

Tennessee is the largest federal program state in the nation, with 62 active surface and underground coal mines. Tennessee's coal resources lie in 22 coal seams in 22 counties. Twelve seams are being mined at this time. Mining in the northern counties is primarily in steep slope areas in the Cumberland Mountains. The relatively flat terrain associated with the Cumberland Plateau makes area-rnining the most common production method in Tennessee's southern counties. The State of Tennessee gained primacy August 10,1982, when its regulatory program was conditionally approved, subject to the correction of certain deficiencies. On May 16,1984, the Tennessee General Assembly repealed most of the Tennessee Coal Surface Mining Law of 1980, effective October 1, 1984. With this action, withdrawal of the state regulatory program was formalized, and on October 1,1984, the Office of Surface Mining's Knoxville Field Office became the regulatory authority. Tennessee is not eligible to receive funds for an abandoned mine reclamation program because it does not have an approved regulatory program. Accordingly, the Tennessee Abandoned Mine Lands Program does not receive federal AML grants. Since 1984, AML projects have been completed under cooperative agreements between OSM and the state; emergency projects are completed by the Office of Surface Mining.

Jan 1, 1992

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow, S. T. Bagley

"Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol.The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment.The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location.In three of the mines filter samples were collected for DEA-associated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, CO2. NO, NO2, and SO2, were well below regulated levels.INTRODUCTIONDiesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992)."

Nov 1, 1995

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By Allen D. Look, Alan A. Sharp

"INTRODUCTION The bottoming of the United Verde sulfide pipe has shortened the expected life of the United Verde mine to a matter of a few years. First located in 1876, this Arizona mine has had a long period of activity, having reached a peak production in 1929 of over 71,000 trans of copper. Through these many years of successful operation, a safety program has evolved in keeping with the proficiency developed in mining the ore body. It is the purpose of this paper to record the safety practices in effect at this mine so that others may have the benefit of lessons ,learned through experience 'and years of work toward an improved accident record.ACKNOWLEDGEMENTSAcknowledgment 'is 'made to ,the Phelps Dodge Corp. for its cooperation in making available data contained in this paper, and to C. E. Mills, general superintendent; W. W. Little, mine superintendent; John Riordan, employment agent; and G. S. Leisk, safety engineer, for their helpful suggestions and information furnished.GENERAL INFORMATIONThe United Verde copper mine is situated just west of Jerome, Ariz., at an altitude of approximately 5,500 feet. Purchased by the Phelps Dodge Corp. in 1935, the mine employs approximately 500 men - 385 underground and 115 on the surface."

May 1, 1949

By O. M. Bishop

"SUMMARYAs a result of the increased demand for fluorspar during the war, the Bureau of Mines investigated numerous fluorspar properties in the southern Illinois field, which is centered in Rosiclare. Among these the J. J. Shelby 40-acre tract on the western edge of the district presented favorable factors that caused it to be chosen /or exploration.H. G. Spiller, formen lessee of the property, had explored the Shelby vein by means of an adit level and winze, and showed it to contain goad values in zinc and fluorspar at the depth explored. A diamond-drill hole with which Spiller explored the vein 78 feet southwest of the winze, however, failed to cut ore. After studying the field evidence, the Bureau concluded that the vein merited further exploration, particularly at a depth of about 440 feet, where the Fredonia limestone would form the foot-wall of the vein and the hanging wall would be the competent Cypress sandstone.Between October 17, 1944, and March 26, 1945, three diamond-drill holes were bored for a total inclined depth of 1,592 feet. Holes 1 and spaced approximately 500 feet apart, explored the vein at 440 feet 4 below the surface. The economic mineralization existed in the vein where cut. Hole 3 cut the fault at approximately 300 feet below the outcrop but failed to find any vein matter except stringers of calcite with small amounts of pyrite."

Apr 1, 1947

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned & name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By Corale L. Brierley

Accumulations of microorganisms in the in-situ leaching environment are believed responsible for plugging of the orebody and thus decreasing uranium extraction. To assess the contribution of microbial growth to this problem, packed columns of ore and core specimens were leached in the laboratory. Samples collected at four in-situ uranium mining operations revealed pseudomonads, xanthomonads, Bacillus sp. and Micrococcus sp. in numbers of 105 cfu/ml. These microorganisms, inoculated into simulated leaching conditions, decreased permeability in two uranium ores by one order of magnitude in 20 days. Hydrogen peroxide (0.2 g/l) alleviated microbial plugging in the laboratory. Periodic injection of hydrogen peroxide through the production well into the orebody may reduce microbial plugging problems in the field.

Jan 1, 1982

By J. H. East

Potash is one of the essential chemicals used in fertilizing soil deficient in natural minerals . Europe uses a large tonnage of potash in the form of easily soluble salts , and this is particularly true of those countries where the natural minerals in the soil have been exhausted owing to intensive cropping of the land . The application of potash to the soil in these countries is essential if normal crops are to be obtained ; during the war , some European countries were unable to obtain sufficient potash , and productivity of the farming areas declined seriously . • The largest -known deposits of potash in the world ; with the possible. exception of Russia , occur in Germany , and the German output of processed salts constituted about 65 percent of world production prior to the war . The German potash-plant installations are large , modern , brick and steel construction and apparently built for a planned operation of many years . Two districts produced approximately 80 percent of the German potash; the Werra -Fulda district , near Vacha , had the largest production , and the Sudharz district , near Nordhausen and Sonderhausen , was second . (Fig . 1. ) Hannover and Stassfurt were two smaller producers . Potash fertilizers are rated in terms of potassium oxide (K20 ) . The usual basis for calculation of production or application of the salt is to reduce the potash content to 40 percent K₂0 .

May 1, 1947

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By Edmund S. Leaver

[In previous reports5/ of ore-testing studies standard methods of conducting; test with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail. In addition to standard tent procedures such as direct cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, it is sometimes necessary to apply other methods, such as preliminary roasting and washing of the calcine with plain or acidulated water before cyanidation. In all of this work standard tenting procedure has been supplements by he necessary assaying and analyses of original ore and test products.]

Jan 1, 1941

By Edmund S. Leaver

[In previous reports 5/ of ore-testing studies standard methods of conduction tests with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail.]

Jan 1, 1941

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974