Search Documents

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

By W. B. Berwald

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gras association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating; this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying; results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made.

Jan 1, 1931

By W. B. Berwald

The United States Bureau of lanes, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed Carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made. The problem, as originally planned, included flow tests on pipe lines in operation, and in each test the measured delivery vas to be compared with the delivery calculated from several common pipe line flow formulas.

Jan 1, 1931

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles &apos;wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

This manual provides instructions for installling, operating, and maintaining protective canopies on the Joy Mfg. Co. cutter. These instructions are based upon two actual installations: one made in a mine and one in the factory. The parts list and engineering drawings for the protective canopies are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other cutters with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other cutters and can determine any necessary modifications if they are not.

Jan 1, 1973

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900&apos;s, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

By S. P. Kinney

The Department of the Interior has recently investigated the atmospheric conditions in tunnels of the Union Pacific Railroad in Utah and Wyoming , by observations made from the cabs of freight locomotives . This work was conducted by the Bureau of Mines at the request of , and in cooperation with , the Union Pacific Railroad Co .. and was brought about by several accidents to members of engine crews while passing through tunnels , from pollution of the tunnel air by exhaust gases from freight locomotives . The object was to determine the cause of gassing accidents , by examining into composition of the air in locomotive cabs while passing through railroad turmels ; to learn the effect of these conditions on the engine crew; and to provide a means of protection for the men so exposed . Gas samples and temperature readings taken in the cabs of locomotives were used in studying the atmospheric conditions to which the locomotive crews were exposed . The symptoms and the physiologica effects produced in men exposed to the atmospheres encountered were studied . The pulse rates and body temperatures were taken , and the determinations of the carbon monoxide content of the blood were made . Various methods for the prevention of gassing and for the protection of men therefrom were considered and tested , among which were the use of mechanical devices for deflecting the smoke away from the engine cab, and the use of various types of gas masks and breathing apparatus . While this investigation is a part of the safety work of the Bureau of Mines in connection with hazards from atmospheres containing carbon monoxide ( CO ) , the results are of particular value to railroads operating steam locomotives through tunnels , and are also valuable to other industries where atmospheres having poisonous gases or of a high temperature and humidity may be present . The results may be summarized as follows :

Jun 1, 1923

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By G. W. Elger

The Bureau of Mines investigated the conversion, at both laboratory and pilot plant scale, of a low-grade ilmenite to chlorination-grade feedstock that could substitute for imported rutile used to produce titanium tetrachloride. The concentrate was derived from the Tahawus, NY, lode deposit of ilmenite-magnetite in rock that contains anorthosite and gabbro. Charges of the ilmenite concentrate, containing 46.6 wt pct Ti02 blended with soda ash, were carbothermically reduced in an electric arc furnace, which separated most of the iron and left a high-titanium slag. However, the slag contained Ca, Mg, and Mn constituents that rendered the material unsuitable for continuous chlorination by causing plugging problems. After being ground and pelletized, the slag was reacted with S02 and air at 7000 to 9000 C, which selectively converted the harmful impurities to soluble compounds that were removed in a subsequent water or dilute HCI leach. In laboratory tests, the combined levels of harmful impurities were decreased from 5 to as low as 0.5 wt pct in leached slags. In pilot plant tests, leached slags sulfated at a rate of 10 lb/h averaged 85.5 wt pct Ti02 with pertinent impurity levels averaging 1.86 wt pct. The leached slag was successfully chlorinated in a laboratory fluidized-bed reactor at 9500 C to extract titanium as TiCI4.

Jan 1, 1986

By Sally A. Shoop

Thirty-seven blasts have been monitored using either three or four seismographs, at four coal strip mines and at a limestone quarry. Statistical analysis of the data shows that square-root, cube-root, and site-specific scaling methods predict peak particle velocities with about the same (low) degree of reliability. Some mines have peak particle velocities that are significantly lower or higher than the U.S. Bureau of Mines averages (Siskind et al., 1980). This suggests that the option provided by the proposed regulations (Office of Surface Mining, 1983), to adjust blast designs based on site-specific measurements could be highly beneficial both to operators and to the public. The frequency spectra reveal that the predominant frequencies were generally less than 50 Hz but several blasts had a significant amount of energy up to 125 Hz. In some cases the vibration energy was concentrated at frequencies corresponding to the delay intervals.

Jan 1, 1983

To alleviate the hazard to personnel and danger to equipment caused by fires on large, mobile vehicles. The Approach: A system which automatically senses a fire at its early stage of development, warns the driver of the danger, and activates fire extinguishers in the zone of combustion, How It Works: The automatic fire protection system utilizes both thermal and optical sensors to detect the heat or light given off by a fire in the area of concern (Fig. 1). The system warns the driver of the hazard and then automatically extinguishes the fire with pressurized S-C class powder. The system can also be activated manually from the operator&apos;s cab or from ground level. Further, the automatic sequencing of the system can be manually overridden by the driver if he determines that the fire sensors have malfunctioned to cause a false alarm.

Jan 1, 1974

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine&apos;s telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By R. S. Dean

Boron compounds have been considered for many years as possible additions to iron and steel. A very recent use of boron-steel rods was for the control of neutron intensity in the graphite-uranium pile at the Clinton plutonium plant(130).4/ Norris(129) reports that slags containing boric oxide reduce the ferrous oxide content of steels and thereby the aluminum required for deoxidation. Boron is not considered an alloying element, but minute amounts produce what is often called a "needled" steel. The study of a series of iron-boron alloys by convenient steps, starting with iron containing no boron, indicated that boron was a hardening agent and made the iron very difficult if not impossible to forge. Then came the discovery that very minute traces of boron are quite different from the smallest amount previously thought worthy of study.

Jan 1, 1946

In 2006, a total of 2,113 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 14.2% of all mining operations. ? Bituminous mines comprised 92.5% (n=1,955) and anthracite mines 7.5% (n=158) of coal mining operations. ? Approximately 71.0% of all coal mines were located in three states: Kentucky (29.2%), West Virginia (21.8%), and Pennsylvania (20.3%).

Jan 1, 2008

By Hal D. Peterson

In research sponsored by the Bureau of Mines, a technique was developed for simulation of heap leaching on uranium ores. The equipment used for this simulation consisted of 2-ft-diam columns, constructed in sections, such that ores as coarse as minus 4-in could be treated in bed depths ranging from 8 to 18 ft with test condition variations. The technique consisted of the separate steps of ore preparation, column loading, charge wetting, leaching, washing, and residue recovery. For the ores studied, sulfuric acid was found to be generally superior to alkaline lixiviants. The rate of uranium extraction by acid leaching proved" to be primarily a function of percolation rate, alkalinity of the ores and oxidant requirements of the ores. Column leaching was closely comparable to field-scale heap leaching in terms of uranium extraction rate and recovery results. Acid and oxidant requirements were lower for the field-scale operation. All column tests, as well as the field-scaly heap, achieved in excess of 96-pct uranium extraction on a Bear Creek, Wyoming ore.

Jan 1, 1985

By (NIOSH) Publication

In 2004, a total of 2,011 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.9% of all mining operations.

Sep 1, 2007

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

By F. S. Crawford

During the course of a study of the safety organizations of the various iron mining companies in the Lake Superior district considerable in¬ formation regarding the methods of safety inspection in use was obtained which may be of value to other companies beginning safety work or contemplat¬ ing changes in their methods. A short description of the safety-inspection methods of eleven of these companies is given in this paper, and in the appendix are illustrated a number of forms used for safety inspections by several of the companies. Most of the companies whose methods are described use few forms for formal inspection. The one long form (10) attached which is used for a general in¬ spection by the safety inspector appears to present a good method for enabling the inspector to check all branches of his inspection and to assure himself that everything has been covered. All names of companies have been deleted from this paper and from the forms because the object is to disseminate information of constructive value rather than to point out the methods of particular companies by name.

Aug 1, 1931

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other&apos;s oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945