Search Documents

By R. E. Head

[This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors5 dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperateive microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau u of Mines, the Utah Copper Co. and the University of Utah.]

Jan 1, 1935

By R. E. Head

This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing, from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperative microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau of Mines, the Utah Copper Co., and the University of Utah.

Jan 1, 1935

By Ren G. Dong, Thomas W. McDowell, John Z. Wu, Chris Warren, Dan E. Welcome, Chun L. Dong

Hand forces are important factors for risk assessment of hand-arm vibration syndrome (HAVS).1 Grip force is one of the most important force components in the operation of powered hand tools. A considerable number of studies on grip force have been reported. It is well known that the grip force applied on a cylindrical handle is not uniformly distributed on each axis across the center of the handle cross-section.2 Therefore, maximum and minimum orientations of grip force exist around the handle. Such orientations have not been clearly identified. In a recently proposed international standard (ISO/CD 15230, 2005),3 it is stated that “the direction of the main gripping force is generally parallel to the z-axis defined in ISO 8727.” 4 This assertion is questionable, and further examinations are required. The objective of this study was to establish a fundamental theory on the distribution of the grip force around cylindrical handles. Methods As shown in Fig. 1, the grip force is defined as a vector composed of normal and shear components (FN & FT) in this study. Fig. 2 shows the hand coordinate system defined in this study, together with the ISO systems.1,4 Based on this novel grip force definition, we derived four fundamental properties and a theorem. More significantly, we formulated a novel hypothesis: similar to Mohr’s circle of stress, the normal and shear components can be represented approximately using an ellipse on the plane of the two force coordinates, as shown in Fig. 3. The maximum and minimum grip normal forces are termed as the first principal grip force (F1) and the second principal grip normal force (F2), respectively. Their corresponding orientations are termed as the first principal grip angle (a1) and the second principal grip angle (a2). A series of experiments were conducted to test this hypothesis. Twelve

Jan 6, 2006

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By Arno C. Fieldner, Howard I. Smith, J. W. Paul, SAMUEL SANFORD.

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1,1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.a Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.b The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1913 to 1916. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22 and 85, the same plan of geographical classification has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1918

By J. R. Thoenen

During the past 6 years the Mining Division of the U.S. Bureau of Mines has prepared many information circulars containing valuable technical data covering the operating details of mining and ore-dressing plants throughout the United States, Canada, Mexico, and other countries. These papers, written for the most part by operating officials in the field, have been designed to comprise a reference library for the operating engineer. In order to make the information contained in these publications more readily available to the busy engineer the enclosed series of reference tables has been compiled. The tabular arrangement is by subject rather than alphabetical order, thus avoiding the bulk of an alphabetical index.

Jan 1, 1935

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

By D. A. Buckingham

The Bureau of Mines evaluated potential availability of domestic nickel from 23 deposits, Evaluations included an estimation of in situ and recoverable resources, applicable mining and processing technologies, and capital and operating costs. Discounted cash flow analysis with a 15-pct rate of return was used to determine the average total cost of production of each operation, Identified in situ resources contain 9.0 million metric tons (t) of nickel; 5.5 million t is recoverable as nickel metal or ferronickel. Demonstrated in situ resources contain 8.2 million t of nickel; 4.8 million t is recoverable as nickel metal or ferronickel. No nickel is available at a total cost of production equal to the January 1983 market price of $3.24 per pound. Analyses indicate that potential annual production can only meet current consumption levels at a total cost of production of $7.60 per pound of nickel, Nickel's availability is contingent on (1) successful adaptability of nickel processing methods to domestic resources, (2) location of a smelting facility, and (3) marketability of byproducts and coproducts. Analyses were performed on the effects of byproduct and coproduct revenues, energy, labor, and transportation costs, and metallurgical recoveries on nickel's availability.

Jan 1, 1984

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but most of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority as collectors in the flotation and agglomerate tabling of micas, feldspars, guartz, clay, and other acidic minerals, but the separation of these minerals from each other necessitated of the study of the flotation of each mineral.]

Jan 1, 1941

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but must of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority- as collectors in the flotation and a. agglomerate tabling of micas, feldspars, quartz, clay, and other acidic mineral, but the separation n of these minerals from each other necessitated study of the flotation of each mineral.]

Jan 1, 1941

By Kenneth L. Cashdollar

The Mine Safety and Health Administration (MSHA) and the West Virginia Office of Miners? Health, Safety, and Training (WVOMHS&T) investigated the explosion at the Sago Mine in West Virginia, which occurred on January 2, 2006, and resulted in 12 fatalities. As part of the investigation, the agencies requested that the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory evaluate the effects of explosions on specific mine ventilation seals and other structures and objects at its Lake Lynn Experimental Mine (LLEM). The results of the LLEM study would assist MSHA and WVOMHS&T in a more thorough understanding of the various questions that arose during their investigations of the explosion. Six large-scale explosion tests were conducted in the LLEM from April to October 2006. The protocols for these tests, and in particular the procedures for constructing various Omega block seals, were developed mainly by MSHA and WVOMHS&T. NIOSH developed the experimental procedures at the LLEM that would provide the required range of explosion pressures against the seals. Three 40-in-thick seal designs using Omega 384 low-density block were constructed in the LLEM and exposed to various explosion pressures. These seal designs are referred to in this report as the ?2001 design,? the ?hybrid design,? and the ?Sago design.? The 2001-design Omega block seal (80 in high) located in crosscut 2 of the LLEM survived all six explosions, with pressure loadings up to 51 psi. The 2001-design Omega block seal (88 in high) in C-drift was destroyed during Test 2, which subjected the seal to a head-on explosion that resulted in a pressure loading of 51 psi. The height difference between the two seals and the orientation of each seal to the explosion were contributing factors. The higher seal would be weaker for the same seal thickness. The hybrid Omega block seal in crosscut 3 survived an explosion at a pressure loading of 25 psi and failed during another explosion at a pressure loading of 39 psi at the seal. Based on these tests, it seems that the hybrid seal design is weaker than the 2001 seal design. The Sago Omega block seals were constructed in crosscut 3 and C-drift before Test 3. The crosscut 3 seal survived a pressure loading of 18 psi and was destroyed during an explosion at a pressure loading of 35 psi at the seal. The C-drift seal survived a head-on explosion that resulted in a pressure loading of 21 psi and was destroyed during an explosion with a pressure loading of 57 psi at the seal. Based on these LLEM tests, it seems that the Sago seal design is weaker than the 2001 seal design, yet it still complied with the requirements of 30 CFR 75.335(a)(2) that were in effect at the time of the mine disaster. During these LLEM explosion tests, the distance of seal debris travel was also measured. In Test 5, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 57 psi, and the seal debris was thrown over 500 ft. In Test 6, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 93 psi, and the Omega block debris was thrown over 900 ft. During these tests, the explosion pressure effects on other structures and objects were also documented. Unless otherwise specified, all of the pressure data listed in this report represent the highest recorded smoothed (averaged over 10 ms) explosion pressure loadings. The information in this report was used by MSHA and WVOMHS&T as supporting data in their analyses and investigative reports of the Sago Mine explosion.

Sep 1, 2009

By R. D. Leitch, J. G. Calverley

"INTRODUCTION Although many investigators have provided information on the strength and other properties of concrete the published literature cites few data on the effect of mixing cement with acid mine waters or on acid resistance of concrete in contact with mine waters. Most of the reported work on the effect of impure waters has dealt with the resistance of cement specimens to ""sulfate waters,"" that is, waters or soils with a relatively high sodium sulfate content. The ""Merriman test"" is used commonly to determine the corrosion resistance of cements for 28 days, but it does not seem certain that a cement having a high sulfate resistance in the Merriman or similar tests necessarily will show correspondingly great resistance to the sulfates of iron and, particularly, to sulfuric acid, which usually are present in acid mine waters. Extensive use of cement mortar for laying up masonry stoppings in coal and other mines and for constructing concrete mine haulageways and shaft linings, coal-storage and other retaining walls, highway bridges, culverts, and many other types of construction where it is difficult to obtain fresh water for mixing or where the structures are later exposed to contact with acid waters makes it important to know the effect of these conditions on cement and whether there is a cement better suited for such work than ordinary portland cement.CONDUCT OF THE INVESTIGATIONFor a short time early in 1935 the opportunity to obtain at least some additional information on the effect of acid mine water on cements was presented by the Relief Works Division, which provided money for irregular and indefinite employment for several months. Purchase of apparatus or material was not permitted under this arrangement, and indefinite duration of the work, intermittent employment, and finally complete cessation of the work prevented planning for extensive investigation of this particular problem."

Jan 1, 1940

Develop a mobile manipulator that one person can use to lift and maneuver 50- to 600-pound loads. It can be used in maintenance shops and mines to reduce lifting accidents (Figure 1 and 2). Background Lifting heavy items is one of the leading causes of injury in the workplace. Mine Safety and Health Administration statistics showed that, in 2004, back injuries accounted for over 20% of all injuries (1,699 cases) and resulted in 110,000 lost days of work. Forty-one percent of those injuries resulted from materials-handling or maintenance activities.1 In addition to back injuries, lifting injuries include hernias, ruptures, sprains, and strains resulting from losing control of the item being lifted. Factors associated with accidents are weight of the item being lifted, awkward postures, inadequate handholds, and the working environment itself. High accident rates were noted when lifting items that ranged from 50 to 600 pounds, particularly in tight working quarters where maneuverability was critical. Research indicated that a mobile lifting arm would eliminate many lifting accidents in environments where other lifting devices (fork lifts, overhead cranes, mobile A-frames) would not be practical. NIOSH has built a first-generation mobile manipulator unit designed to be used on hard, level floors such as in a shop. The complexity of motion, number of moving parts, compact design, and design constraints of the manipulator required advanced computer-aided design work (Figure 3). As a result of the design work, thirty-eight claims are included in the patent applications. NIOSH will be conducting field trails and working with manufacturers to put the manipulator into industrial use.

Dec 1, 2006

By E. C. Lane

"In a previous paper the Bureau of Mines. 3/ presented in condensed tabular form all analyses of Texas crude oils made by the Bureau up to March 193K. This previous report states;The first Al well in Texas was drilled near Oil Springs, Nacogdoches County, in 1863-67. However, the first oil field of major importance in the State was discovered at Corsicana,Navarro County, in 1895. Since that time the petroleum industry try in the State has spread and grown until today petroleum from Texas is an important commodity in world petroleum markets.Since March 1939 samples of Texas crude oils from many new fields, and some older fields not covered in the previous report, nave been analyzed. Those analyses arc reported in the present paper. The annual production by years from 1896 to 1940, inclusive, taken from the figures in the Bureau of Mines Minerals Yearbook, are given in table 1. Production for 1896-1940, inclusive, totals 6,579,715,000 barrels.Various authors reported upon developments and production in the Texas fields in the Transactions of the American Institute of Mining and Metallurgical Engineers, Petroleum Division, for 1941. 4/"

Apr 1, 1943

By Edwin S. Secor

The Federal Bureau of Mines conducted a field survey of 153 bituminous coal strip and auger mines to estimate coal recovery from surface mines in the Eastern United States. Recovery was calculated from field data by measuring coal losses resulting from mining coal and leaving barriers. Mean total recovery for strip mining in States east of the Mississippi River was 83.0 percent and ranged from 72.3 percent for Tennessee to 91.3 percent for Maryland. Mining losses and barrier losses were 10.1 and 7.7 percent, with standard deviations of 4.8 and 10.4 percent, respectively, indicating that barrier losses, although less than mining losses, were more variable. Mean total coal recovery varied only slightly for the two regions studied; 82.7 percent for Appalachia and 84.3 for the Midwest. Total recovery grouped by mining method--contour, area, and mountaintop removal--was 79.8,84.7, and 85.3 percent, respectively. Mean auger recovery was 35.9 percent; of the total average loss of 64.1 percent, over one-half resulted from design limitations while the remainder was attributed to operating losses. The wide recovery range at individual mines indicates the variability of the eastern surface coal mining industry. Because of this, care should be exercised in applying the results of this report to reserve estimates other than those of a general nature.

Jan 1, 1977

By Robert Stefanko

This report abstracts project work performed for the USBM Grant No. GO-133077 during the period 19 June 1973 to 15 October 1974. Five reports have been separately produced and are as follows: 1. Mine Electrical Systems Evaluation - Cable Splicing, 2. Mine Electrical Systems Evaluation - Explosion-Proofing of Mine Containers, 3. Mine Electrical Systems Evaluation - Transient Analysis, 4. Mine Electrical Systems Evaluation - Mine Power System Performance, and 5. Mine Electrical Systems Evaluation - Model Coal Mine Electrical System Specifications. Abstracts of each comprise the balance of this executive summary, and 50 copies of each volume have been forwarded to the USBM under the terms of the grant agreement.

Jan 1, 1974

By Fredrick L. Johnson

No mineral resources were identified during the investigation of the White Cloud-Boulder RARE II area. Only a few claims have been located in the area and only two workings were found. However, there has been considerable exploration and mining activity near the RARE II area. Sand and gravel resources are abundant but similar deposits occur closer to market areas. There are no known coal, oil, or gas deposits. Most of the RARE II area is underlain by volcanic rocks. The likeliest host rocks for metallic minerals are the metasedimentary rocks exposed in the south part of the area; there is potential for zinc and silver resources at a prospect in that part. Traces of scheelite and powellite were observed in the Kent Peak-Ryan Peak area along hair-line fractures in calcareous country rock. While no significant concentrations of the minerals were found, their presence, a northwest alignment of prospects with similar deposits, and an abundance of dikes near the deposits, suggest that the intrusive system (Summit Creek stock) exposed near the head of Little Fall Creek may extend to the northwest under the RARE II area.

Jan 1, 1983

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947