Search Documents

By Thomas M. Barczak, Dennis R. Dolinar, Gabriel S. Esterhuizen

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this “uncontrollable convergence” be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffness of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

By Steven K. Ruggieri

This report describes the operation and maintenance of the Mobile Inert Gas Generator for use in the Remote Sealing System for fighting underground coal mine fires. Seals are emplaced in mine passageways between the fire zone and the rest of the mine isolating the fire zone from the mine. The seals consist of fly ash that has been pneumatically conveyed via inert gas through a borehole connecting the surface and the passageway, Inert gas is used as the fly ash seal transport medium (instead of fresh air) since the introduction of large volumes of fresh air in the vicinity of the fire zone would be undesirable. The inert gas generation equipment is mounted on two flatbed trailers, the "hot" trailer and the "cold" trailer. The hot trailer contains the combustion and cooling equipment. The cold trailer contains the moisture removal and compression equipment necessary to convey the fly ash. The system is self-sufficient and requires only fuel and fly ash deliveries. The Inert Gas Generator has been thoroughly performance tested and has been operated in the field for approximately 200 hr. The system was employed in the demonstration of the entire Remote Mine Sealing System at the Jenney Mine in the Fall of 1978. The system is currently available for fighting any future underground coal mine fires.

Jan 1, 1980

By Lewis M. McNay

The strength characteristics of hydraulic sandfill modified by varying quantities of type III portland cement and two flocculants were investigated by the Bureau of Mines. Three different sand-cement ratios were examined using different percentages of flocculant. Two other experimental variables were curing time and weight-percent solids for hydraulic mixture. Results of unconfined compression tests with strain are discussed. Maximum strength was achieved with 0.5 weight-percent of ferric sulfate per ton of solids when the slurry mixture was 75 weight-percent solids. The bearing capacity of hydraulic sandfill is reduced by increasing the water content and decreasing the amount of cement mixed with sandfill.

Jan 1, 1976

By David Garry, Michael J. Brnich, Lynn L. Rethi, Henry P. Cole, William J. Wiehagen, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet and the trainee's questionnaire. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.1 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Supervisors, Safety Personnel and Accident Investigators Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Developing a strategy or plan to prevent slips and falls Following correct procedures in conducting an accident investigation Preventing unsafe work practices Recognizing and instituting hazard controls in the section Identifying and implementing safe work procedures Location: Underground coal mine section Problem: You have been the general mine foreman at White Rock Mine for 4 years and have worked at this mine for 12 years. The mine superintendent calls you into his office. He gives you an accident report of an employee in 4-G section who was injured while carrying rock dust bags from the rock dust car to a battery powered scoop. It is several days after the accident and the mine superintendent assigns you and the safety supervisor to thoroughly investigate the accident to determine all the contributing factors. Your job is to make specific recommendations to prevent future slipping/tripping accidents.

Jan 10, 1999

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By William O. Vanderburg

The fluorescence of many minerals, when excited by different wave lengths, of ultraviolet radiation, has long been recognized as a spectacular laboratory phenomenon. Since the original display in the British Museum, the phenomenon has been used frequently for educational purposes and public demonstrations. Its practical application for the rapid detection of certain minerals in ores and mill products at the zinc mine at Franklin, N. J., has been described.3 Due to technical improvements in ultraviolet-radiation apparatus, fluorescence has found a new field of application in the tungsten-minim; industry. Although fluorescence of scheelite (calcium tungstate) has been known for a number of years, the practical application of the phenomenon is the outgrowth of a program of cooperative research conducted by Ott F. Heizer, manager of the Nevada-Massachusetts Co., Inc. , Mill City, Nev., and Dr. Paul F. Kerr of Columbia University. Special portable lights for fluorescing scheelite have been developed and utilized in underground geological work. Thanks are due Ott F. Heizer for permission to publish data included in this paper.

Jan 1, 1935

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

A series of laboratory evaluations examined the impact of water spray pressure, curtain setback distance, and external and underboom spray use for controlling respirable dust levels and sulfur hexafluoride tracer gas concentrations around a continuous mining machine. This mining machine was equipped with a flooded-bed dust scrubber and was positioned in the box or slab cut. Exhaust line brattice was used for all tests. Dust levels were measured in the return airway and at locations representing the operators of the continuous mining machine and the standard and off-standard shuttle cars. Increasing water pressure or using the underboom sprays produced no significant impacts on dust levels, although their interactions did produce some significant impacts. Increasing curtain setback distance often elevated dust levels, likely by reducing the amount of airflow reaching the face. Use of the external sprays created additional airflow around the mining machine that pushed the dust cloud past the scrubber inlets. This significantly increased dust levels at all sampling locations. Tracer gas levels were measured on the off-curtain and curtain sides of the cutter head and in the return airway. Increasing water pressure generally led to significantly increased gas levels on the curtain side, although a slight decrease was observed on the off-curtain side with the machine in the box cut. Increasing setback distance elevated gas levels on both sides of the cutter head and in the return by limiting the quantity of ventilation airflow reaching the face. Use of the external sprays provided additional airflow along the off-curtain side of the machine, significantly reducing gas levels in this region. These sprays adversely impacted the dilution and removal of gas on the curtain side of the cutter head. Use of the underboom sprays adversely impacted gas levels on both sides of the cutter head. Use of the external sprays provided the best control of respirable dust and face gas concentrations. The smaller increases in miner operator dust levels produced by these sprays were offset by larger reductions in face gas levels on the off-curtain side of the cutter head. Although the underboom sprays minimally impacted respirable dust levels, use of these sprays was not recommended because they increased face gas levels.

Jan 1, 2007

By J. M. WADSWORTH

The purpose of this bulletin is to describe the methods of constructing and operating representative types of plants in the United States used for removing the light hydrocarbons from petroleum by continuous distillation, such plants being commonly known in the trade as topping or skimming plants. In the discussion of each plant an endeavor has been made to arrange the text similarly in order to facilitate comparison and to emphasize the important features. The various experimental values for the specific and the latent heats of the oils apply approximately to the oil treated. Careful experiments with each oil and its commercial fractions were not justifiable in view of the purpose of this report. It is regretted that limitations for recording data at the different plants made impossible the determination of a heat balance for each, which would have provided an equitable method of comparing efficiencies. The writer has confined himself to a comparison of the relative efficiencies of the distilling apparatus alone by the following method: Effi . f till d tt" _ Heat theoretically required. ciency 0 SIS an se mgs - Heat content of fuel consumed. The plants described are all in California where the topping industry has had its growth accentuated by the character and the use of the oil handled. The scarcity of suitable coal made the adoption of other fuel necessary, and the heavy oil of California supplied the need. To raise the flash point and to dehydrate this oil, various plants have been developed. However, the topping industry is represented in other fields; the Roxana Petroleum Co. of Cushing, Okla., and the Warner-Quinlan Asphalt Co. of New Jersey, are operating Trumble plants, and Texas and Oklahoma operators have been experimenting with different pipe retorts for continuous running. In addition to the reasons for topping cited above, in California topping has other purposes which give the plants practically a universal field in the oil industry. These additional purposes are (1) to remove the lighter constituents of the oil prior to storage for a long period, thus reducing the losses from evaporation, (2) to dehydrate and clean the oil, and (3) in conjunction with a complete refinery, to remove the lighter fractions cheaply and quickly, leaving a residue to be rerun for lubricants, coke, and other products. The reader in studying a plant for possible adaption to his own use should note that local considerations enter into the design and size of a plant. Several questions present themselves, as follows: 1. What type is suitable for the oil? 2. How much money is available for construction? 3. Will the volume of residuum be large enough for heat exchange with the crude? 4. Can the heat content of the vapors be used to reduce the cooling-water requirements? 5. What method will best recover the heat from stack gases? 6. Are the various pieces of apparatus adequate in size and best adapted to their purpose? 7. Is every possible provision made for the recovery of waste heat? 8. What products will be made, and what volume of each? 9. Is there provision for the recovery of light vapors? 10. Will the saving of fuel justify the capital and maintenance charges on the regenerative apparatus contemplated? It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished. The reader will find fuel economy and heat recovery emphasized throughout the descriptions. The conservation of the available petroleum supply is of the utmost importance, and the Bureau of Mines presents this paper to encourage the hearty cooperation of operators to that end. The Baume gravity scale used throughout the report is that of Tagliabue with a modulus of 141.5 for conversion to specific gravity.

Jan 1, 1919

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By F. X. McCawley

The Bureau of Mines, in pursuing its goal of extending the life span of strategic materials, conducted field corrosion studies at the East Mesa Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to determine the optimum materials of construction for use in geothermal mineral energy resource recovery plants. These studies included characterization of geothermal environments and in situ corrosion testing. The corrosion resistance of 10 alloys exposed to 5 brine and steam process environments was evaluated using the low-salinity, high-temperature brine from geothermal well Mesa 6-1. Of these alloys, Hastelloy C-276, Hastelloy S, Incone1 625, titanium-2nickel, and 316 L stainless steel had excellent resistance to corrosion in all of the process environments; E-Brite 26-1 and 430 stainless steel had fair resistance. Although general corrosion rates for 4130 steel and 1020 carbon steel were substantially higher than those of the other iron-base alloys, these two alloys could prove useful in low-salinity process environments because of their low cost. Aluminum alloy 5005 was the least corrosion resistant alloy and pitted severely. Scales formed on all of the alloys in every process environment. Calcite, aragonite, and an amorphous silicate were the major components of the scales.

Jan 1, 1980

By Shail J. Butani

In 1986, the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 yr; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. coal mining workforce from March through September 1986. A companion report, Information Circular (IC) 9193, "Characterization of the 1935 Metal and Nonmetal Mining Workforce:' provides similar information for the U.S metal and nonmetal mining industry.

Jan 1, 1988

By John R. Troxell

"INTRODUCTION The Ahles iron mine, also known as the Pequest mine, in Warren County, N. J., was operated continuously for 15 years and was still in ore when it closed in 1916.Tie property was examined by an engineer of the Bureau of Mines in March 1943. 3/ This examination led to an investigation of the deposits by the Bureau by diamond drilling two holes under the old workings to determine whether the extends downward.This report describes the work done at the Ahles mine by the Bureau and presents the data obtained.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report.The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation was under the general supervision of J. B. Zadra, acting regional engineer, and under the immediate supervision of G. D. Jermain, district engineer for the States of Pennsylvania, New Jersey, Maryland, and Delaware. The author was in direct charge of the project.The chemical analyses for the project were performed at the College, Park, Md., laboratories of the Bureau of Mines under the direction of M. S. Sheftel. The ore-dressing tests were conducted at College Park under the direction of Frank Lamb. Preston E. Hotz, of the Federal Geological Survey, logged and interpreted the drill cores."

Apr 1, 1948

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By Hewitt Wilson

Until recent years the term "whiting" was applied exclusively to the water-ground chalks of certain north European countries. In many industries these are still considered superior to the whiting made from domestic limestone and marble. However, the latter material has replaced much of the European whiting in the American market, largely due to improvements in grinding and classification by American manufacturers.4 To encourage the domestic industry, the Bureau of Mines in 1931 undertook a study of the preparation of whiting from American raw materials and a comparison of the finished products with European whitings.

Jan 1, 1937