Search Documents

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By Travis Q. Lyday

During 1981, Ecuador's gross domestic product (GDP) increased by a reported 4.8% in real terms, a slight improvement over that of 1980. In current prices, the CDP in 1981 was estimated at $13.7 billion.2 The inflation rate increased to 15.6% according to official figures, above that of 1980. Ecuador's production of petroleum increased 3% in 1981 compared with that of 1980. The consortium of Corporación Estat al Petrolera Ecuatoriana (CEPE), the state oil company, and Texaco, Inc., produced almost 98% of the total from their Putumayo Basin operations in Oriente, the eastern jungle region. In sharp contrast, output from the Santa Elena Peninsula Fields, where oil was first produced commercially in 1921, continued to decline, producing only 510,000 barrels, a decrease of almost 8% compared with that of 1980.

Jan 1, 1983

By Selim E. Woodworth

This paper, describing the milling practice on the Mother Lode as typified in the mill of the Argonaut Mining Co. at Jackson, Amador County, Calif., is one of a series prepared by the United States Bureau of Mines. The data herein presented and furnished through the courtesy of E. A. Stent, managing director and vice president of the Argonaut Co., covers operations from 1914 through the year 1929.

Jan 1, 1931

By Wiliam L. Crentz

The importance of Somerset County, Pa., as a coal producer is due in large measure to the presence reserves of low-volatile bituminous coals. Although many coal beds of minable thickness are present, the important reserves are to be found in those beds underlying the Pittsburgh bed. The Kittenning beds and Freeport beds, which are responsible for the bulk of the present coal production in Somerset County and contain the largest reserves to meet future coal requirements, are usually thin and entirely free from impurities. The Pittsburgh bed, which has been such an important coal deposit in the coal areas immediately west and south of Somerset County, is of secondary importance in this county. Although generally rather friable, Somerset County coals have enjoyed wide receptability as excellent coals and to some extent have been utilized in the metallurgical market.

Jan 1, 1951

Protect mine rescuers from heat-induced stress that drastically cuts their endurance and saps their strength. Approach To prevent exhaustion caused by thermal stress, a rescuer can wear a liquid-cooled hood and vest which absorbs heat, thereby reducing the heat-induced strain on the rescuer's heart and circulatory system. How It Works Liquid coolant is continuously circulated through a self-contained system in which the coolant is chilled by a heat sink on the wearer's belt. The coolant, which is a mixture of alcohol and water, is pumped from the heat sink to bladders inside the hood and vest where it absorbs body heat. After absorbing heat In the hood and vest areas, the coolant returns to the heat sink where it is rechilled by passing through a tube coiled around a steel can containing a block of ice. To adjust the temperature of coolant leaving the heat sink unit, a valve can be operated by the wearer, causing part of the flow to bypass the coil. A small pump and a rechargeable battery are also part of the assembly.

Jan 1, 1979

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By Charles H. Fulton

One of the first matters to receive attention from the Bureau of Mines when it was authorized to undertake investigations relating to wastes in the mineral industries was the smoke problem at smelting and ore-roasting plants. This bulletin is published by the bureau primarily for persons who seek information on the subject of metallurgical smoke but are unacqllainted with the technical language of metallurgy. It is, of course, not possible to free a techniCal subject entirely from teclmicalities, but, 80 far as possible, statements are made in plain and simple English. Metallurgical smoke causes considerable friction between the metallurgical industry and agriculture in certain parts of the country. Owners of smelting plants are making every effort to devise ways and means to do away with possible damage and annoyance from smoke and are meeting with success. The problem is peculiarly difficult in this country because of the large tonnages of material that must be handled. The solution of the problem is not yet at hand and much work still remains to be done. As the mineral industry is one of the great basic industries of the country and of necessity is entitled to full consideration, it should be accorded freedom to work out the smoke problem to the benefit of all concerned. The effort is made in this paper to present the problem of metallurgical smoke as it actually exists, without bias of any kind. The writer takes this opportunity to express his indebtedness to the sources of information on which he drew, many of which are enumerated in the selected bibliography at the end of this paper. In connection with the author's use of the present tense in describing plants and methods, the reader should note that none of the references in that bibliography is of later date than 1913. Much information was obtained by personal visits and by correspondence, and thanks are hereby tendered to all persons who kindly furnished data. The writer desires to thank particularly F. G. Cottrell, chief chemist of the Bureau of Mines, for criticism and comment.

Jan 1, 1915

By D. Harrington

During the 5-year period 1906-10 inclusive, 84 major disasters (a major disaster being one in which 5 or more lives are lost) occurred in the coal mines of the United States, or an average of 17 per year, and the total number of fatalities from coal-mine gas and dust explosions (major plus minor) for the 5 years aggregated 2,338 or 477.6 per year. The monotonous continuance of coal-mine disasters month by month aroused the people of the United States to such an extent that it was felt necessary for the Federal Government to try to do something looking to the avoidance of the admittedly excessive loss of life in our coal mines, and this was one of the deciding factors in the establishment of the United States Bureau of Mires in 1910. That results have been obtained in this particular cause of coal-mine accidents may be seen from the fact that for the year 1933 but one major explosion disaster occurred in the coal mines of then united States and the total number killed in that disaster was 7. Unquestionably the coal-mining industry through use of oaf or mining practices and aided by the various kinds of work of the Bureau of Mines looking to the prevention of mine fires and explosions is in large part responsible for this very creditable change. If the gas and dust explosion fatality rate of 1.059 per million tons of coal produced during the period 1906-10 inclusive had continued to the first of January 1934, instead of the 6,373 deaths which actually occurred due to gas and dust explosions, there would have been 13,480. Hence, during the 23 years existence of the Bureau of Mines there has apparently been a saving of about 7,102 probable deaths, or an average of more than 300 per year, from gas and dust explosions as against the number which would have occurred had the 1.059 gas and dust explosion fatality rate for the period 1906-10 continued. Thirty-nine persons were killed in all kinds of explosions (both major and minor) in the coal mines of the United States in 1933; if the 1.059 gas and dust fatality rate of the 1900-10 period had been in effect in 1933, about 400 persons world have been killed. Unquestionably, the various teachings of the U.S. Bureau of Mines looking to the avoidance of explosions and fires in mines have had a vital influence in reducing the number of explosions and fires and also in decreasing their destruction in case they occur.

Jan 1, 1934

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Boltsfork 7 1/2-minute quadrangle in eastern Kentucky was selected as the study area. Results indicate that of the original 280.2 M tons of resource in the quadrangle, only 99.8 M tons (35.6%) is recoverable at a mining cost of $25 per ton or less.

Jan 1, 1994

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

By Jeffrey S. Newman

This report establishes a methodology for the evaluation of gas detection devices and is the result of a critical investigation into the basic principles defining gas detector performance. A scheme is presented to evaluate the performance of a test sample of gas detectors based on the detector type and intended application. Test procedures, worksheets, test apparatus, glossary and statistical methods for handling test data arc given. In addition, evaluation standards and test parameters are identified. It is intended that this report serve as a comprehensive framework for the eventual certification of all gas detectors for mine applications. A plan is proposed and recommended for the quantification and implementation of evaluation standards for gas detection device certification.

Jan 1, 1980

In 2007, a total of 725 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Nonmetal mines com-prised 4.9% of all m ining operations. ? Mines producing common clay comprised 25.4% (n=184) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the U.S. Virgin Islands.

Aug 1, 2009

By K. M. Connor, O&apos

Variations in overburden geology must be considered in applying subsidence prediction methodologies developed by the U.S. Bureau of Mines (USBM). To characterize rock mass overlying high-extraction coal mines, the USBM utilizes a computer spreadsheet program and modified Rock Mass Rating (RMR) system. The spreadsheet calculates an RMR based on a bed's engineering properties determined from core logs and laboratory tests. An in situ deformation modulus and a bending stiffness are computed for each bed. Stiffness-versus-depth plots identify groups of beds with similar stiffness. Large variations in stiffness between adjacent beds are considered significant horizontal discontinuities where slip is likely. Time domain reflectometry (TDR) is used to verify this hypothesis by measuring shear displacement along such discontinuities. A model of the overburden is built by assuming that a near-surface laminated beam exists above a transition zone in which large plastic slip occurs along horizontal discontinuities. Increasingly thicker groups of beds are modeled to determine the most probable beam thickness based on a comparison with measured deflection profiles. The inverse of maximum beam deflection is an index parameter known as "bridging potential," a single value that incorporates both overburden geology and mine geometry.

Jan 1, 2010

By William R. Barton

Anthracite has been mined from the Narragansett Basin of Rode Island and Massachusetts sporadically, and with limited success, for more than 170 years. Beginning in 1974, interest in the coal of the Basin was renewed because of increasing prices and supply uncertainties involving petroleum products. During 1974-77 the Bureau of Mines analyzed 28 samples of Basin coals and conducted washing tests on 20 of them. Results, reported herein, indicate that the coals are low-sulfur, moderate- to high-ash anthracites and semianthracites, suitable for physical preparation to a product generally containing less than 10 percent ash. Additional exploration, sampling and testing will be required to permit appraisal of the potential value of the Narragansett Basin coal resources.

Jan 1, 1977

By John D. Warne

"INTRODUCTION Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, Investigation of the fluorspar deposits of the Northgate area was begun in June 1944 and completed in March l946. Mining Operations were active in the district during most of the period of investigation.The Fluorspar, Fluorine, and Camp Creek mines develop the two more promising vein systems known in the area, the Fluorspar group of claims covering one vein system and the Fluorine and Camp Creek groups the other. Figure 1 shows the location of the properties. The Fluorspar and Fluorine properties were operated (except during the winter months) by the Western Fluorspar Corp. The Camp Creek mine was operated during 1943 and 1944 by Kramer Mines, Inc.The properties were examined April 20 and again November 4 to 12, 1943, by C. R. Wilfley, a Bureau of Mines engineer, who recommended work to determine ore reserves and to serve as a guide for development. Investigations by the Bureau of Mines covered all three properties."

Aug 1, 1947

By E. P. Youngman

The rapidly growing demand for titanium pigments has aroused new interest in actual and potential sources of supply of titanium- bearing ores , which only a comparatively few years ago were almost unmarketable . This paper , which supplements a general circular entitled " Titanium" ( Information Circular 6365 ) , represents a summary of current trade literature and Government reports , together with some hitherto unpublished material that has accumulated in the files of the Bureau of Mines . The purpose of this pamphlet is simply to indicate the commercial possibilities of the deposits , and the discussion is confined almost entirely to the three commercial ores , ilmenite , rutile , and magnetite ( titaniferous iron ore ) .

Oct 1, 1930

By G. P. Houston

This is the final, report submitted for the Contract No. H0220002 with the U. S. Bureau of Mines for the design and development of a Permissible Automatic Data Acquisition System (PADAS) to measure and record roof stresses in underground mines Basically the PADAS is a portable, battery powered, 24-channel data acquisition system designed for safe unattended operation of up to 30 days duration in explosive environments. The unit will accommodate twenty-four pressure transducers or eight borehole deformation gages (or any combination) at distances up to 300 feet from the PADAS to measure pressures up to 10, 000 psig. All 24 channels as a selected group are scanned sequentially at one of several selectable rates.

Jan 1, 1973

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No. H0155113, "Noise Abatement of Continuous Mining Machines." It reviews, briefly, the aboveground tests performed on a Jeffrey 120M conveyor that were documented in Vol. I of the subject contract; and describes the performance of treatments implemented on underground equipment. The noise level at the operator's position in the aboveground-test facility was reduced from 101.5 to 91 dBA using treatments with satisfactory - aboveground - durability. Extensive underground evaluation has been performed only on the constrained layer damping, which has reduced the conveyor noise by 2 to 6 dBA depending on the operating conditions, and has been shown to be sufficiently durable. Other promising candidates for exploratory evaluation include resilient layers for the top/bottom decks, and smoother discontinuities between adjacent conveyor sections.

Jan 1, 1983

By Thys B. Johnson

The mine system analysis and evaluation study presented in this report was part of the U. S. Bureau of Nines' Tertiary channel project conducted under the Heavy Metals program. The Badger Hill pit, located on the west end of the San Juan Ridge area, near Nevada City, California, was the site of the Bureau's field work. The objectives of this study were: (1) Determine potential alternative mining systems for some of the large tertiary channel gold-bearing gravel deposits, and (2) Identify areas of technology where further investigation would be merited because of their potential inclusion in a mining system for such deposits, The study involved the development of a mineralized block inventory, an economic block inventory, determination of optimum ultimate mining limits and a preliminary economic mining system evaluation. Computer programs were developed and utilized for each of the study phases stated above. The sampling program conducted at Badger Hill by the Bureau Delineation Group together with confidential drill hole data provided by the San Juan Gold Co. formed the basic gold values and distribution information from which a deposit model was developed. The deposit was divided into minable block units and net economic values were assigned to each block for various configurations of both open-pit and underground mining methods based on cost and performance data provided by the various Bureau of Mines Research Centers. A number of controllable variables such as: (1) Mining method (open-pit and underground), (2) depth of mining cut, (3) production rate and (4) equipment type and capacity were evaluated. The prime measures of effectiveness on which the mining systems where judged were discounted cash flow rate of return and maximum utilization of natural resources. The analysis showed that underground mining of the Six-Mile Tertiary channel gold-bearing gravel deposit under consideration was uneconomical and did not permit maximum recovery of the resources within the channel. It was also apparent that mining the Six-Mile Deposit for gold alone is uneconomical or at best marginal at a gold price less than $80 per ounce. The analysis showed that the potential for an economic mining operation within the Six-Mile Deposit exists when the gravel resources of the channel are considered together with the gold. It was determined that the highest rate of return would be realized with a 20-year open-pit mining operation yielding 745,000 ounces of -gold and 55 million cubic yards of usable gravel.

Jan 1, 2012

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983