Search Documents

By Stephen P. Case, Stephen Castellucci, William Parsons

In this paper, the authors present a step-by-step discussion of dimension stone production at a New England granite quarry. The quarry mines a rare pink granite which is used for facings and panels in the construction of high rise buildings around the world. The discussion includes geological considerations, block layout, drilling, explosives loading, block handling, and mobile equipment utilization.

Jan 1, 1990

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By William C. Lane

The Pacific Northwest has an abundance of seamy, coarse granite and basalt rock. It is used primarily for road construction. Small quarries are opened nearest the road work to cut the cost of hauling. The crushers are portable. Small diameter holes 2 1/2" to 3 1/2" are placed close together to insure proper fragmentation. It is not unusual to load and shoot 100 to 700 holes 40' deep.

Jan 1, 1986

By Fred C. Drury

The introduction and growth of modern chemical explosives based upon prilled ammonium nitrate has been the most significant development in the explosives industry during the 20th century. These modern chemical explosives have been of incalculable value to our society. Their use has permitted a reduction of blasting costs, improved safety, and the development of new resource sources which would not have been accessible without this new technology.

Jan 1, 1980

By Jesus A. Pascual de Blas

After 30 years of development and introduction, electronic initiation systems are now well established in blasting applications, both mining, quarrying and civil works. In terms of blast technology, it could be considered that timing is the new challenge: how to define the most appropriate sequence to improve fragmentation, reduce vibrations, avoid dilution, eliminate damage… Some classic tools have been updated and adapted to the new scenario, and are giving us good performance; on the other hand, others should be considered obsolete, given the accuracy of electronic initiation systems has exposed these tools to incoherent conclusions. Besides, other tools have appeared and are in use, providing new approaches to old issues. Additionally, not only the technical side has to be considered: safety, security, economics are well present in daily blasting activity and affect to the final decision: are electronic initiation systems the right answer to my blast?

Jan 1, 2019

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Richard Turnbull

Maules Creek mine is an open cut coal near Boggabri in the Gunnedah Basin of New South Wales, Australia. The mine is currently operating at an annualised run rate of 9.5Mt of saleable coal. The plan is to ramp up production to 13Mtpa. Maules Creek has multiple seams each with varying depths; the inter-burden ranges from a few metres thick to greater than 30m (98ft). Due to this, Maules Creek mine is utilising truck shovel operations rather than a cast/dozer push operation.

Jan 1, 2018

When CIL presented their new theory of the Breakage Process and Delay Blasting at the 74th Annual Meeting of the CIM in 1972(1), there was hardly any open pit operation in Canada that was using longer than 25 msec. delays. To the contrary, 10 and 15 msec. surface relays were common, which in our opinion were no delays at all for open pit blasting.

Jan 1, 1979

By Abraham Lindo

Panama’s current economical growth demands an increase in electric power supply; projected energy supply for 2012 exceeds the demand by as little as 2%. In an effort to comply with the demand, several different hydroelectric projects, promoted by the government, are currently under construction and each of them vary in generating capacity, construction design and complexity.

Jan 1, 2013

By James R. Kennedy

The recent drop in world gold prices is driving many northern Nevada underground gold mines to look for new ways to improve and enhance current mining operations. Continuous improvement programs at these mines are finding the means to increase mine productivity while reducing total production cost. This paper looks at developments in the drill and blast program at Independence Mining Company’s Murray mine.

Jan 1, 1999

By Dale Ramsey

Located in the Chestnut Ridge Mountains of Southwestern Pennsylvania, the Casparis mine named for the founder Kenneth Casparis operated from 1916 until the early 1950. producing crushed stone for construction and railroad ballast. The rock was transported by aerial buckets to a railroad tipple nearly 1000’ (304.80 meters) below the mine. The mine property is now owned by the Pennsylvania Game Commission and is located in the Loyalhanna limestone seam with 4 primary entries that are approximately 40’ (12.19 meters) high by 30’ (9.14 meters) wide and extend over 2 miles (3.22 kilometers) into the mountain.

Jan 1, 2006

By R Holmberg, P A. Persson

Recent developments in the methods of measuring rock motion close to the contour at the moment of blasting have given an improved understanding of the extent of rock damage caused by different charge systems. The paper presents the new results and the methods of prediction of damage zones which are used in Sweden for the design of contour blasting rounds. A survey is given of the tools and the techniques for smooth blasting that are now used on a routine basis in Sweden.

Jan 1, 1978

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

By Julia Creasey, Natalie Hodgson, Claire Ward, Craig Davies, Helen Sarginson

"Emulsion explosive producers are attempting to lower the cost of emulsion production by using lowquality ammonium nitrate in emulsion formulations. Low quality ammonium nitrate contains additivessuch as anti-caking agents and crystal modifiers which contaminate the emulsions causing instability. This presents a need for an effective emulsifier that will maintain emulsion stability under thesechallenging conditions."

Jan 1, 2017

By J. Silva, T. Worsey

The Worsey-Silva equation determines the optimal row timing for the smallest fragmentation and allows fragmentation models to be adjusted due to row timing. The equation utilizes the concept of dynamic confinement to determine when the best time to fire the next row or sequence series would be if the smallest fragmentation is desired. Full-scale testing was conducted at an aggregate quarry in Ontario to support the theory and equation. The full-scale testing comprised six (6) blasts, two (2) different contractors, and three (3) different sequences. The test parameters were kept consistent, besides changing the timing between sequential charges to explore the timing sequence’s influences on fragmentation. From this research, the theory of dynamic confinement relating to row timing was discovered, and the equation to determine the optimal timing for the smallest fragmentation was derived. An equation to adjust fragmentation based on row timing was derived from the full-scale testing and literature review. The Worsey-Silva equation can be used with other fragmentation models as it takes the fragmentation results from the other models and adjusts them based on the row timing used. The paper explains the theory behind the equation, the research supporting the findings, and the developed Worsey-Silva equation for row timing

Jan 1, 2024

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By S. Green, R. Yang

Blasting is a commonly used method for rock fragmentation in mining operations for mineral extraction. It involves breaking the rock mass into small pieces, and ideally creating micro fractures within the small pieces. Such micro fractures could significantly reduce the energy required for subsequent processes like crushing and comminution. Additionally, micro fractures would enhance the rock-fragraments fluid permeability thereby enhancing desired chemical reactions during certain processing operations. This paper presents recent developments of the Multiple Blasthole Fragmentation (MBF) model, which simulates blasting rockmass fragmentation. The MBF model allows estimating rock strains experienced during the blast, for various blast design parameters and geometries. The intent is to correlate these strains with created micro fractures in the blast rock fragments. Adjusting blast design parameters in the MBF model of explosive loading and delay timing allows blast optimization. Such optimizing would create desirable strains to enhance micro fractures within the rock fragments. This would improve mining operations by enhancing downstream operation efficiency, thus reducing costs.

Jan 1, 2024

By Lifeng Li, Jhon Silva-Castro

"Signature Hole Technique is one method to assess the vibration waveform of a production blast.Methematically, it is the convolution between a prior measured waveform of a single blast hole (signature) and a given time delay sequence (comb function). Being an advantage, the inverse operation of convolution, known as deconvolution, can be used to estimate the signature."

Jan 1, 2017

By Eduardo Lozano, Vilem Petr

The use of explosives brings countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition, and avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation.

Jan 1, 2017

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018